Bond 52157 Manual de usuario
Owner’s Manual
Model# 52157
Stainless Steel Patio Heater
Intertek
5019004
Bond Manufacturing Co., Inc. | Page 2
WARNING
Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so
may result in a re, explosion, injury or death.
SAFETY INFORMATION
•
• THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a
ventilated space and shall not be used in any enclosed area.
• This unit is to be used with propane gas only! (sold separately)
• Do not attach a remote gas supply to this unit.
• Only use propane gas for this unit.
• This unit is not intended for natural gas.
• Converting this unit to natural gas is dangerous and not recommended. The conversion of this unit
will void the manufacturer warranty.
• Do not use any solid fuel or charcoal for this unit.
• If the propane gas tank is leaking gas, you may hear, see, or smell a hiss. Do the following:
1. Disconnect the propane gas tank. 2. Do not attempt to x the problem yourself. 3. Contact your gas
supplier or re department for help.
• Applying too much propane may result in gas pooling and will not burn. Allow fresh air into the unit
so that the remaining gas may escape.
• Do not use a ame to check for gas leaks.
• The max. inlet supply pressure: max. Gas supply 11 in w.c. (2.74kPa).
• Use LP propane tanks with the following dimensions: diameter 12 in, height 18 in. - capacity 20 lbs.
• You must use a propane tank that has a collar to protect the gas valve.
• DO NOT ll tank over 80 percent full.
• The tank system must be set up for vapor withdrawal.
• Discontinue use if any part of the propane tank is damaged. Rust and dents may be hazardous and
should be inspected by a gas supplier.
• Do not burn anything other than the provided materials for this patio heater.
• Do not operate unit until all parts are fully assembled.
• Do not paint or color any part of this heating unit.
• Unit may be hot while in use, do not attempt to move it while in use.
• Never leave this heating unit unattended while in use.
• This unit is not intended for cooking.
• Keep any ammable items away.
• Keep a safe distance to avoid burning skin or clothing.
• Do not sit or rest hands or feet on this heating unit.
• Never place hands or ngers on upper portion of this unit while in use.
• Keep all electrical cords and fuel supply hose away from heated surfaces.
• Combustible material should not be within 48 inches of the top of the unit, or within 48 inches
around the entire unit.
• Keep the appliance area clear and free from combustible material, gasoline and other ammable
vapors and liquids.
• If the ame goes out while burning, turn the gas valve off. Wait 5 minutes before repeating the initial
lighting procedure. Once you have a ame started, hold down the control knob for 1 minute.
• Do not add water into the unit.
• Do not operate unit if any part has been under water. Call a service technician to replace any
The installation of this unit must adhere to local codes or Propane Storage and Handling Code,
CSA B149.2.
1-866-771-2663 | Page 3
damaged parts should this occur.
• Do not disconnect any part while unit is in use.
• Do not store a spare propane tank on or near this unit.
• If the heating unit is indoors, detach the propane tank and leave outdoors.
• Do not operate on a boat or vehicle. This unit must be used on a at surface and outdoors ONLY.
• Always remove protective cover before operating (if applicable).
• Check for leaks after not using the unit for long periods of time.
• Children should never operate this unit. Children must be supervised while near this unit.
• Keep gas tank at least 5 feet away from unit when lit. (if external tank)
• The maximum gas supply pressure is 250psi.
• All installation and repair should be done by a qualied professional. This unit should be
inspected annually and cleaned regularly.
• Inspect all elements of this heating unit before each use. If there is damage, the burner must be
replaced.
• Be aware of the hazards of high temperatures and stay away from the unit to avoid any burns or
injury.
• The gas supply tank should be constructed and marked with the specications for the LP gas tanks
of the U.S. Department of Transportation or the National Standard of Canada CAN/CSA-B339, LP gas
tanks, spheres and tubes for Transportation of Dangerous Goods; and Commission.
• The LP gas tank must have a listed overflling prevention device and a QCCI or Type I, (CGA791) LP
gas tank connection.
• This heating appliance should not be used on plastic or articial wood decks.
• Children and adults should be alerted to the hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the area of the appliance.
• Clothing or other ammable materials should not be hung from the appliance or placed on or
near the appliance.
• Any guard or other protective device removed for servicing the appliance shall be replaced
prior to operating the appliance.
• Installation and repair should be done by a qualied service person. The appliance should be
inspected before use and at least annually by a qualied service person. More frequent cleaning
may be required as necessary. It is imperative that the control compartment, burners and
circulating airways of the appliance are kept clean.
Only use the regulator and hose assembly provided with this unit. Replacement parts must be supplied
directly by Bond Manufacturing Co., Inc.
Inspect the burner before use of this unit. If the burner shows any kind of damage, do not operate
the appliance. For assistance with repair or replacement of the burner or any other parts, calls Bond
Manufacturing Co., Inc. at 1.866.771.2663.
NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas
valve is turned “OFF” before assembling. Do NOT attempt to assemble without proper tools.
Storage of an appliance indoors is permissible only if the cylinder is disconnected and removed from
the appliance. A cylinder must be stored outdoors in a well-ventilated area out of the reach of children.
A disconnected cylinder must have dust caps tightly installed and must not be stored in a building,
garage or any other enclosed area.
•
SAFETY INFORMATION
BE CAREFUL: WHEN CERTAIN MATERIALS OR
ITEMS ARE STORED ABOVE, BESIDE OR UNDER
THIS HEATER WHILE IN USE, THEY WILL BE
SUBJECT TO RADIANT HEAT AND COULD BE
SERIOUSLY DAMAGED.
Combustible materials should not be within
inches of the top of the unit, or within inches
around the entire unit.
48"
48" 48"
Bond Manufacturing Co., Inc. | Page 4
48
48
1-866-771-2663 | Page 5
HARDWARE
Anchoring Arm
Bolt M6x10
M6 Nut
Anchor
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any parts are missing or damaged, do not
attempt to assemble the product.
Estimated Assembly Time: 30 minutes
Item Description Qty
2
6
6
3
9
2
9
9
3
1
M8 Flange Nut
Bolt M8x16
M6 Flange Nut
Bolt M6x30
Reflector Spacer
Washer
Screw M6x10
Cap Nut
Wing Nut
Wrench
5
4
(pre-assembled on part C)
AA
BB
CC
DD
EE
FF
GG
HH
I I
JJ
KK
LL
3
MM
6
NN
6
OO
3
PP
Post Bolt (pre-assembled on part F)
MM NN OO PP
(packed with part I)
(2 pcs packed with part I)
Bolt M6x10
Tools required for assembly (not included): Phillips Screwdriver
CONTENTS
Item Description Qty
A 3
B 1
C 1
D 1
E
Burner Assembly
1
F
Upper Post
1
G
Regulator
3
HBase 1
I 1
Tank Housing
Wheel Assembly
Support Bracket
Reflector Panel
Center Reflector
J
Lower Post
1
Bond Manufacturing Co., Inc. | Page 6
1-866-771-2663 | Page 7
ASSEMBLY INSTRUCTIONS
AA
BB
x 2
M8 Flange nut
x 2
BB x 3
Bolt M8x16
Bolt M8x16
Step 1
Hardware Used
MM x 3
Anchoring Arm
NN x 6
Bolt M6x10
OO x 6
M6 Nut
Step 2
Attach 3 pcs support brackets (G) to base (H) using
3 pcs bolts M8x16 (BB).
Note: Keep the support bracket with belt in the middle.
Hardware Used
Be sure that the wheel assembly is parallel to the base.
Tighten bolts securely. AA
OO
NN
MM
BB
I
H
Turn the base upside down, then attach wheel assembly (I)
to base (H) using 2pcs M8 flange nuts (AA) and 2pcs bolts
M8x16 (BB). Attach 3pcs anchoring arm (MM) to base (H)
using 6pcs M6 nuts (OO) and 6pcs bolt M6x10 (NN).
CC x 6
Hardware Used
EE x 6
Attach lower post (F) to support brackets (G) using 6pcs bolts
M6x30 (EE) and 6pcs M6 flange nuts (CC).
Tighten bolts securely.
Bolt M6x30
M6 Flange nut
Step 3
F
ASSEMBLY INSTRUCTIONS
Load tank housing onto post, slide tank housing down.
Remove the 4 pcs preassembled bolts M6x10 (DD)
from the burner assembly (C).
Insert the regulator (J) from the top end of the upper post (E),
then attach the burner assembly (C) to upper post (E) using
the four bolts removed at the beginning of this step.
Tighten bolts securely.
Step 4
Step 5
Hardware Used
x 4
J
Bond Manufacturing Co., Inc. | Page 8
HH
F
E
HH x 2
Post bolt
Step 6
Remove the 2 preassembled bolts (HH) from the lower post (F).
Insert the regulator (J) from the top end of the lower post (F).
Insert upper post (E) to lower post (F), then tighten two posts
using the 2 bolts (HH) removed at the beginning of this step.
Hardware Used
J
Bolt M6x10
1-866-771-2663 | Page 9
B
A
7-1
II
JJ
II
WARNING: Remove protective cover before assembling.
Note: If necessary for proper alignment of reflector
sections.
Fully tighten all of the screws.
Step 7
Attach 3 pcs reflector panels (A) to center reflector (B) using
9 pcs Screws M6x10 (II) and 9 pcs cap nuts (JJ).
x 9
x 9
Hardware Used
Slide 3pcs washers (GG) over threaded end of spacer.
Step 8
to burner assembly (C) firstly.
Attach 3 pcs reflector spacers (FF) and 3 pcs washers (GG)
Tighten the reflector spacers.
Attach the reflector assembly to the top of reflector spacer
(FF) using 3 pcs washers (GG) and 3 pcs wing nuts (KK).
GG
KK
x 9
Washer
FF x 3
Reflector
spacer
x 3
Wing nut
Hardware Used
ASSEMBLY INSTRUCTIONS
PP
PP
ASSEMBLY INSTRUCTIONS
Place the propane gas tank (not included) on the base.
Tighten the belt to ensure the propane gas tank is fully
secure.
Turn the cylinder valve on the tank clockwise
to close the propane tank. Attach the regulator
(J) to the cylinder valve by turning the
regulator coupling nut clockwise. Make
sure it is fastened securely and tighten
connections by hand only.
Step 10
Optional: Use the anchor (PP) to fasten the product into
the ground.
Step 9
Step 11
Anchor x 3
J
Hardware Used
Bond Manufacturing Co., Inc. | Page 10
Tabla de contenidos
Idiomas:
Manuales populares de Calentador de otras marcas
Empire Heating Systems
Empire Heating Systems WCC65 Manual de usuario
Wetekom
Wetekom 92 86 43 Manual de usuario
Desa
Desa SPC170-F Manual de usuario
Watlow
Watlow Watrod Electric Tubular Heaters Manual de usuario
Haverland
Haverland ECO-DRY GPS Series Manual de lista de piezas
Stelpro
Stelpro ASILVC2060 Series Manual de usuario