Bodet Style 12 Manual de usuario

Style 12

INDEP. QUARTZ

MIN. - 1/2 MIN.

AFNOR / IRIG B

DHF / RADIO

INSTALLATION AND OPERATING INSTRUCTIONS

When receiving goods please chek nothing is broken otherwise make a claim near shipping compagny.

B.P. 1

49340 TRÉMENTINES

FRANCE

Tél. : 02 41 71 72 00

Fax : 02 41 71 72 01

www.bodet.com

Réf. : 605863 F

CAUTION :

Only skilled person is authorised for the maintenance service of this clock.Any modification

on this product renders the warranty invalid.

Table of contents

1) INSTALLATION ...........................3

2) ELECTRICAL POWER SUPPLY ..................3

3) CONNECTION TO A TIMING NETWORK .............4

3.1. INVERTED POLARITY PARALLEL DISTRIBUTION or AFNOR / IRIG B 4

3.2. INVERTED POLARITY SERIES DISTRIBUTION (1/2 minute series)4

4) RADIO SYNCHRONIZED CLOCK : STARTING UP. ........5

4.1 France Inter or DCF radio synchronised clock 5

4.2 DHF clock 5

4.3 AFNOR / IRIG-B clock 5

5) CONNECTING A TEMPERATURE PROBE TO A STYLE 12 CLOCK 6

6) CONNECTING A TIMER CONTROL UNIT TO A STYLE 12 S CLOCK 6

7) CONNECTING A DOUBLE FACE CLOCK .............7

8) CONFIGURATION AND SETTING THE TIME ...........8

8.1. Configuration menu 8

8.2. Time setting 8

8.3. Reset DHF clock to “Initialisation” mode 9

9) TEST .................................10

10) DISPLAY BRIGHTNESS ADJUSTMENT .............11

11) DATA BACK UP ..........................11

12) CLEANING .............................11

APPENDIX : TECHNICAL CHARACTERISTICS............12

1) INSTALLATION

Unhook the wall support (A) from the clock using the

key (B), then remove the plug-in connectors.

Fix the support (A) to the desired spot using the 4 wall

plugs and the 4 screws provided.

- Hooking onto a vertical bracket or side bracket :

support (A) fits onto bracket reference no. 935001, and

also to the chain suspension reference no. 935002.

- A table support is also available, reference no. 935003.

2) ELECTRICAL POWER SUPPLY

- Remove the black protective cover on the terminal block (C). Connect the mains power

supply - 115 or 230 Volts 50/60 Hz depending on the model - to the terminal block

(maximum wire cross section 1.5 mm2with 5 mm bare).

Replace the protective cover. Block the wires with cable clamps (S).

N.B.: The Style clocks have been designed for a mains power supply of 115 or 230 Volts

+/- 10 % (depending on the model). This clock is protected by a 1,25 A - 250 V fuse (F1).

The mains supply unit for this clock must include a 10 A interlocked circuit breaker.

This circuit breaker has to be switched off in case of maintenance operation.

E.g. 230 V clocks will work equally well in countries where the nominal mains voltage is 220

or 240 Volts.

- If the clock is a part of a time distribution network, or if it has a built in radio antenna (Radio

FI or DCF) or to a timer control unit, please follow the instructions in Chapters 3 to 7.

- Carry out configuration, set the time and adjust the clock’s light intensity as indicated in

Chapters 8 to 10.

- If the display “sticks” at a particular time, check that the operating mode that you have

selected is “Ind” (cf. Chapter 8).

EDC

3) CONNECTION TO A TIMING NETWORK

Connect dual voltage 115 or 230 V 50/60 Hz (depending on models ) (cf. chapter 2)

3.1. INVERTED POLARITY PARALLEL DISTRIBUTION or AFNOR / IRIG B

(minute //12-24-28 volts, 1/2 minute// 12-24-48 volt)

- Connect the impulse line to the “//” and “COM” terminals on the terminal block (D).

- Select the impulse type (minute, 1/2 minute or AFNOR depending on the model) and set

the clock time (Chapter 8).

3.2. INVERTED POLARITY SERIES DISTRIBUTION (1/2 minute series)

- Connect the impulse line to the “COM” and “series” terminals on the terminal block (D).

- So as to avoid cutting out the network when disconnecting one slave clock, also connect

the 33 Ohm 1/2 Watt resistance (supplied) between the “COM” and “series” terminals on the

terminal block (D).

- select the impulse type (1/2 minute) and set the clock time (Chapter 8).

Master clock

Details of series distribu-

tion connection // or

AFNOR

Master clock

Details of series distribu-

tion connection

Resistance (supplied)

of 33 ohms 1/2 Watt

4) RADIO SYNCHRONIZED CLOCK : STARTING UP.

4.1 France Inter or DCF radio synchronised clock

After connection of the clock on its support, orientate the antenna ( F ) until the LED (1) is

blinking regularly.

- If reception is good, the clock will automatically set the time after a few minutes. In areas

where radio signal reception is difficult manually set the clock time (chapter 8) whilst

awaiting radio synchronization (reception at night is in general better).

4.2 DHF clock

-After connection of the clock on its support, orientate the antenna ( F ) in line with the clock.

On leaving the factory, the DHF clock is set in “Initialisation” mode. On the initial powering

up, the time is initialised at 0h00, 1 jan. 2000.

The clock memorises the address of the transmitter and switches to normal mode

automatically when time is received.

4.3 AFNOR / IRIG-B clock

-On the initial powering up, the time is initialised at 0h00, 1 jan. 2000.

The clock automatically set up its time base to the correct time when receiving the time

message.

Caution : if the AFNOR signal is lost, the clock continues to operate for 1 hour in

independent mode and then the display goes off. Only the separating colon “:”, which stops

blinking after 1 minute without signal, remains on, indicating that power continues to be

supplied to the clock.

5) CONNECTING A TEMPERATURE PROBE TO A STYLE 12 CLOCK

Caution : Style 12S cannot display temperature.

Set up the temperature probe in a well ventilated spot out of

the sun and the rain and at a maximum distance of 50m.

Care should be taken in choosing where to position the

probe in order to ensure that the temperature readings are

correct. Avoid south-facing frontages, metal parts and

draughts.

- Connect the temperature probe to the “TEMP-” and

“TEMP+” terminals on the terminal block (E).

- If the probe is connected the wrong way round, the clock

will display 0°C.

- The probe cannot be submerged.

6) CONNECTING A TIMER CONTROL UNIT TO A STYLE 12 S CLOCK

The timer control unit reference no. 936400 operates both ways, to count up and to count

down. It has the following different functions : Start, stop, intermediate time, closing of a

contact sharp at the end of count up or countdown (to stop on a pre-set time). The timer

control unit can drive up to ten Style 12 S clocks.

- Connect the timer control unit to the terminal block (E) with

a 4 wire cable (T-, T+ and 2 wires for 12 V power supply).

- To chain several Style 12 S clocks to the same timer

control unit, connect the terminals T- and T+ to their

respective terminal blocks (E) with a 2 wire cable (telephone

pair).The first clock is still connected to the timer control unit

with a 4 wire cable.

- For further details, please consult the timer control unit instruction manual ref.: 604821.

Brown

White

Max. 500 m and 10 Style 12S

Maxi 20m

7) CONNECTING A DOUBLE FACE CLOCK

- Open up the 2 clocks by unscrewing the 9 screws (R).

- Pass the connector (HE14) through the grommet (S) on each clock, and connect it to the

male connector (T).

Caution :

1 - Cables for respectively the master clock and the slave clock are not the same : there is a

specific mark for each of these.

2 - The cables for the master is one meter long. This cable can not be extended as it may

cause a problem with the clock operation mode.

- Close up the clock again.

- Connect the 115 or 230 V 50/60 Hz mains supply (depending on the model) (cf. Chapter 2)

and whatever the type of master clock, the slave clock wire to the master clock.

R S

Slave clock

Female DIN

connector

Male DIN

connector

Master clock

8) CONFIGURATION AND SETTING THE TIME

- Note : Position of the “Select” and “+” keys

- These two keys are located on the lefthand side of the clock.

- The “Select” key is above the “+” key.

In all the menus, you use the “+” key to choose your settings and the “Select” key to confirm

them.

8.1. Configuration menu

To access this menu, press the “Select” key for 3 seconds.

- The clock displays the previously selected operating mode :

Operating Mode Display

Independent or integrated radio synchronization

Slave Minute

(on INDEP. QUARTZ/MIN. - 1/2 MIN. Model)

Slave 1/2 Minute

(on INDEP. QUARTZ/MIN. - 1/2 MIN. Model)

Slave Afnor / Irig B

(on INDEP. QUARTZ/MIN. AFNOR-IRIG B model)

Note : If an antenna has been connected, the “Ind” mode is selected automatically. Pressing

“+” will have no effect and it is not possible to select “Min”, “1/2 M” or “Afn”.

8.2. Time setting

In the configuration menu, when the selected mode, e.g. “Ind” is displayed, press the

“Select” key to confirm.

The clock then moves on to the set time mode.

The hours flash

Set the hours and confirm.

The minutes flash

Set the minutes and confirm.

NB. the seconds are reset to zero each time the minutes are reset.

Then, if a temperature probe is connected, the clock is switching to the option for selecting

the alternative display of time and temperature, otherwise this last press enables to escape

from “Setting the time” menu after running the self test :

-Switching on all the Leds for 2 seconds,

-Switching off all the Leds for 1 second,

-Return to normal display.

Alternative display menu for time and temperature :

Alternate display time/temperature :

Press “+” key

Display of temperature only

After selecting the option, press “Select” key to confirm, the temperature adjusting menu

displays :

Press “+” key to adjust the displayed temperature by adding up to +9°C or decreasing up

to -9°C.

This adjustment enables to calibrate the displayed temperature according to the official

temperature.

Once the adjustment is over, press “Select” key to confirm.

This last press enables to escape from “Setting the time” menu after running the self-test :

-Switching on all the Leds for 2 seconds,

-Switching off all the Leds for 1 second,

-Return to normal display.

8.3. Reset DHF clock to “Initialisation” mode

On leaving the factory, the DHF clock is set in “Initialisation” mode.

However, it can be necessary to set it again in this mode.

Press the “+” key for 3 seconds to enter in the TEST menu.

The TEST menu displays :

- the construction of the time message as and when the data arrive,

- only the separating colon when the data do not arrive.

From this TEST menu, press the “Select” key for 6 seconds.

- The clock displays 0:00 for 5 seconds then display disappears. The clock is now reset to

“Initialisation” mode. Press “+” key to exit this menu.

9) TEST

A brief self-test (on and off) is carried out automatically on exiting the configuration menu.

A more complete test can be carried out on request.

To start this test, press the “+” for 3 seconds

This test displays :

- The software version number,

- Total light-up for 3 seconds,

- Total switch-off for 3 seconds,

- The current operating mode (“Ind”, “Min”,"1/2 M" or “Afn” depending on the model)

for 2 seconds.

If the mode is “Ind” :

Case 1 :

No antenna detected : end of the test, return to normal display.

Case 2 :

Antenna detected, not recognized :

- “Ant” displayed for 2 seconds,

- dynamic reception : “0:00" displayed, the ”:" flash as the bits are

decoded and then the digits are displayed as they are received.

After 10 minutes : end of the test, return to normal display.

You can exit this test mode by pressing the “+” key.

Case 3 :

Antenna recognized :

- recognized antenna type (“FldC” or “MSF”) displayed for 2 seconds,

- dynamic reception : “0:00" displayed, the ”:" flash as the bits are

decoded (idem LED of the antenna) and then the digits are displayed as

they are received.

After 10 minutes : end of the test, return to normal display.

You can exit this test mode by pressing the “+” key.

If the mode is “Min” or “1/2M” :

End of the test, return to normal display with the “:” that remains constant until the

reception of the following pulse.

If the mode is “AFn” :

Otros manuales para Style 12

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Reloj de Bodet

Bodet

Bodet Opalys 14 Manual de usuario

Bodet

Bodet Profil 930 Manual de usuario

Bodet

Bodet 10 Manual de usuario

Bodet

Bodet Profil 930 Manual de usuario

Bodet

Bodet Profil 750 Manual de usuario

Bodet

Bodet NTP 947 17x W6 Manual de usuario

Bodet

Bodet Style 12 Manual de usuario

Bodet

Bodet STYLE II 7 Manual de usuario

Bodet

Bodet Cristalys Manual de usuario

Bodet

Bodet Profil TGV 950 Manual de usuario

Bodet

Bodet Style 5 Seconde Manual de usuario

Bodet

Bodet Cristalys 14 Manual de usuario

Bodet

Bodet Style Mondiale Manual de usuario

Bodet

Bodet Profil 750 Manual de usuario

Bodet

Bodet BTX6015 Manual de usuario

Bodet

Bodet 5 Seconde Manual de usuario

Bodet

Bodet Opalys 7 Manual de usuario

Bodet

Bodet Opalys Date Manual de usuario

Bodet

Bodet Profil 930 L Manual de usuario

Bodet

Bodet Sigma Mod Instrucciones y recetas

Bodet

Bodet 5 Seconde Manual de usuario

Bodet

Bodet DHF/DCF Interface Manual de usuario

Bodet

Bodet Style 5S Manual de usuario

Bodet

Bodet Profil 960 Series Manual de usuario

Manuales populares de Reloj de otras marcas

Silicon Laboratories

Silicon Laboratories SI5324 Manual de usuario

Heathkit

Heathkit GC-1005 Manual de usuario

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manual de usuario

Andrew O'Malley

Andrew O'Malley DOTKLOK Manual de usuario

ALGE-Timing

ALGE-Timing ASC3 Manual de usuario

Nixie Clock

Nixie Clock Divergence Meter Manual de usuario

La Crosse Technology

La Crosse Technology WS-8256-AL Manual de usuario

Mini Gadgets

Mini Gadgets MCPro Manual de usuario

Casio

Casio TMR-200 Manual de usuario

Progetti

Progetti ILTEMPOSTRINGE Manual

BVItech

BVItech BV-101 Manual de usuario

Progetti

Progetti KALIMERO Manual

La Crosse Technology

La Crosse Technology WT-3141b Manual

La Crosse Technology

La Crosse Technology W86531 Manual de usuario

Sharp

Sharp SPC900 Manual de usuario

La Crosse Technology

La Crosse Technology 404-50447 Manual de usuario

Datexx

Datexx DF0063 Manual de usuario

LG LEC-005 Manual de usuario