Boca Systems LEMUR-X Manual de usuario

1065 South Rogers Circle • Boca Raton, FL 33487 • Phone (561) 998-9600 • Fax (561) 998-9609

Roll Holder Installation Lemur-X (p/n 424051-U)

This roll holder kit is designed to be used with either a Lemur-X or Lemur-Z model printer. This kit will work

with a roll that has a minimum cord inner diameter of 1.0”or greater.

Kit will include mounting plate, roll holder arm, spindle, stopper disc and mounting hardware.

Some parts my look different than the above photo

1. Attach the spindle onto the roll holder arm using one ¼” Hex head #8 Taptite screw.There are two

mounting locations that may be used depending on roll outer diameter size.

2. Install the roll holder arm mounting plate onto the printer using two 3/16”Hex Head #4 Taptite screws.

The plate may be installed on either side of the printer.

3. Install the one 3/32”Allen head screw into the mounting plate. Location will depend on the desired

angle you want to set the arm at. See last page for diagram of possible arm positions angles.

a. TOP HOLE = 60°, 0°, - 60°

3/16”Hex Head

#4 Taptite

3/32”Allen head

screw

1/4" Hex Head

#8 Taptite

3/32”Allen wrench

TOP

8”or smaller

6”or smaller

For #8 Taptite screw at step # 4

b. BOTTOM HOLE = 90°, 30°, - 30°, -90°

4. Install the roll holder arm onto the mounting plate and secure it in place with the provided ¼” Hex head

#8 Taptite screw. Below photo shows the arm set to the 30° positions. Arm position will vary

depending on what degree position is used.

5. Slide the roll holder block onto the spindle with the sensor tab towards the roll.

6. Slide the block side the block all the way to the roll holder arm. See below photo.

7. Orientate the sensor tab so it is parallel to the floor or bottom of the printer.

8. Tighten the Philip screw on the block to hold it in place.

Sensor tab

BOTTOM

Sensor tab

Spindle

Roll holder arm

This side towards

roll holder arm

Outer holes line

up with Allen

screw

Center hole lines

up with #8 tap

hole

Philip head screw

9. Tear off a full turn of the paper from the new paper roll. Caution: This is important as the outer end of

the paper is usually secured to the roll with glue or other adhesive substance that may cause paper jam

or damage the print head.

10. Place the Receipt roll onto the spindle. If the thermal side of the media is towards the outside of the

roll, the roll will turn towards the printer (as shown in the photo below). If the thermal side of the media

is towards the inside of the roll, the roll will turn away from the printer.

11. Install the stopper disc onto the spindle and slide into place. The stopper should be positioned to prevent

the roll from moving too much from side to side but be allowed to spin freely.

12. Once you have the stopper in the desired position, tighten the Philip head screw to hold the stopper in

place.

13. Once the stopper disc is in place it should not be necessary to remove it to install or remove a roll, provided

the roll core inner diameter is 1.0”or greater. The core should slip over the disc.

14. If the roll holder has been configured for use with 58mm center infeed guide you will want to run the printer

to ensure media is feeding properly into the printer. If not then make necessary adjustment to the roll

holder block and stopper disc for proper alignment with the printer.

Must be

completely

removed

Stopper

Disc

Stopper

Disc

Philip head

screw

06.10.21

Otros manuales para LEMUR-X

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora de Boca Systems

Boca Systems

Boca Systems Micro Manual de usuario

Boca Systems

Boca Systems Lemur-Z Manual de usuario

Boca Systems

Boca Systems Lemur Manual de usuario

Boca Systems

Boca Systems Lemur-C Manual de usuario

Boca Systems

Boca Systems LEMUR-X Manual de usuario

Boca Systems

Boca Systems SUBATM Manual de usuario

Boca Systems

Boca Systems Mini MB Manual de usuario

Boca Systems

Boca Systems LEMUR-M Manual de usuario

Boca Systems

Boca Systems LEMUR -C Manual de usuario

Boca Systems

Boca Systems Lemur-S Manual de usuario

Boca Systems

Boca Systems Lemur-C Manual de usuario

Boca Systems

Boca Systems LEMUR-ERAM Manual de usuario

Boca Systems

Boca Systems Micro Plus Manual de usuario

Boca Systems

Boca Systems Lemur Manual de usuario

Boca Systems

Boca Systems FSP 44 Manual de usuario

Boca Systems

Boca Systems LEMUR-FDIO Manual de usuario

Boca Systems

Boca Systems Adjustable MC Ghost Manual de usuario

Boca Systems

Boca Systems Mag 42 Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario