BobsCNC E4 Manual de usuario
Page 1
E4
Page 2
·································································································4
Safety First
·······························································································5
Required Tools
Good Ideas
For More Informaon
···············································································6
·························································7-17
Wood Components (included with the kit)
Required Hardware (included with the kit)
Illustrated Steps
···································································18-38
Wood Components (included with the kit)
Required Hardware (included with the kit)
Illustrated Steps
·········································································39-46
Wood Components (included with the kit)
Required Hardware (included with the kit)
Illustrated Steps
········································································47-58
Wood Components (included with the kit)
Required Hardware (included with the kit)
Illustrated Steps
···············································59-63
·····································································64-67
Wood Components (included with the kit)
Required Hardware (included with the kit)
Illustrated Steps
································································68-72
Wood Components (included with the kit)
Required Hardware (included with the kit)
Illustrated Steps
Page 3
··························································································73-77
Wood Components (included with the kit)
Required Hardware (included with the kit)
Illustrated Steps
·····················································································78-86
Tips to Keep Your Controller From Being Damaged.
················································································87-91
……………………………………………………………………………………...92
················································93
···························································································94
……………………………………………………………………………….. 95
···································································································96-102
Warranty and Return Policy ··································································96
Miscellaneous Parts List········································································97
Diagram for Plywood Components ·······················································98 -102
Page 4
Specifications
The E4 CNC Router has the following features:
• Rigid laser cut frame.
• Fully supported rail system with SG20U bearings.
• GT2 belt drive on X and Y axis.
• 5/16-18 coupler nut on the Z axis.
• Home switches on all axes.
• MDF T-Slot Spoilboard with T-Nut inserts.
The assembled footprint:
Length: 30" (630 mm)
Width: 37.2" (945 mm)
Height: 18.9" (480 mm)
Assembled Weight:
32 lbs.
Cung Area:
X: 24" (610 mm)
Y: 24" (610 mm)
Z: 3.3" (85 mm)
your
Routers have a high voltage power supply and use bits that spin at 30,000
rpm with cung edges that are hazardous. The operator must understand
these hazards and is responsible to take appropriate safety precauons be-
fore operang the Router.
Page 5
• Two ½” end wrenches to ghten Z Bearing nuts.
• A pair of long nose pliers to hold the nuts.
• Diagonal Cuers or sharp knife to trim nylon es.
• Calipers or measuring tape to measure part placement.
• Small standard screwdriver to connect electronics.
• Small Phillips screwdriver to mount home switches and stepper motors.
• Medium Phillips screwdriver to build the main components.
• Sand paper to remove laser marks on the faces.
• M4 Star Driver for DeWalt disassembly.
• LOCTITE® 243 thread lock (ngernail polish can be used as a substute).
• Wood Glue (e.g. Titebond®) for Spoilboard Assembly
To operate the E4 CNC Router you will need:
7/16” & 5/8” wrench to change router bits.
Computer with control soware for GRBL.
Material for Project.
1/8” or 1/4” Router bits.
Dry lubricaon (e.g., graphite, Teon® or silicon spray).
Tools you may need for the electronic setup include:
Mulmeter to correctly connect the power supply and stepper motors. A mulmeter is a good tool to have for general
electronic trouble shoong.
Getting Started
• We recommend using a large at, clean working surface for assembling your E4.
• All screws (unless noted) should be installed snug, then rotated one 1 to 2 1/2
turns.
• Light sanding of the wood surfaces will clean up the marks made by the laser.
• Painng or applying stain with a clear coat will give added protecon to the wood
components.
• During assembly try placing 1 inch strips of blue painters tape behind the T-Slots to
hold the nuts in place during assembly.
*For More Information: Click on the Links
Page 6
Short Zip Tie
Long Zip Tie
M5
Washer
5/16”
-
Page 7
5/16”
Page 8
Page 9
Page 10
“” -
Tabla de contenidos
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad