BMGi E8 Manual de instrucciones
Installation &
User Manual
E8 Swing kit
Solar or Electric Systems
EGA-04 Controller
Table of Contents
Important Safety Information .................................................................... 3 - 5
Technical Specications .................................................................................. 6
Kit Inclusions ............................................................................................ 7 - 8
Optional Extras ............................................................................................. 9
Example Setup of Single Swing Gate ..........................................................10
Example Setup of Double Swing Gates ...................................................... 11
Before You Begin (Power Options & Solar Panel) ...................................... 12
Proper Gate Installation .............................................................................. 13
Installation Pointers ................................................................................... 14
Cardboard Template ................................................................................... 15
Installatioin of Gate Opener ........................................................................ 16
Pull or Push to open setup .......................................................................... 17
Installing the Gate Stop .............................................................................. 18
Manually Opening and Closing Gate .......................................................... 19
Pull-to-Open Setup .............................................................................. 20 - 25
Installing Post Brackets .......................................................... 21 - 22
Installing Gate Bracket .................................................................. 23
Push-to-Open Setup ............................................................................ 26 - 32
Installing Post Brackets .......................................................... 28 - 29
Installing Gate Bracket .................................................................. 30
Transformer info ......................................................................................... 33
Solar Panel info .......................................................................................... 34
Learning Your Control Board ................................................................. 35 - 37
Remotes ..................................................................................................... 38
Menu Settings .....................................................................................39 - 41
Control Board Specications and Details ............................................ 42 - 43
Other Considerations ................................................................................. 44
Troubleshooting ......................................................................................... 45
Usage Problems ....................................................................................... 46
Attaching Control Box Lid ......................................................................... 46
Other Information ...................................................................................... 47
WARNING
Important Safety Information
Gate equipment has hazards associated with its use and therefore by installing this product the
installer and user accept full responsibility for following and noting the installation and safety
instructions. Failure to follow installation and safety instructions can result in hazards developing
due to improper assembly.
READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before attempting to install and
use this automatic gate operator. This gate operator produces a high level of force. Stay clear of
the unit while it is operating and exercise caution at all times.
All safety instructions should be read and completely understood by installer and the owner prior
to the installation of the E8 auto gate system. This product is designed and manufactured for the
use indicated in the manual.
Remember that all automatic gates are intended for vehicular gates only. A separate gate or en-
trance must be installed for pedestrian use. Any other use, not expressly indicated may damage
the product or be a source of danger.
Swing Gate Motor - Model E8
E8 swing gate motor is suitable for light - medium opened framed gates, eg farm gates or pool
fencing style etc. Do not use it on large sized gates which exceed the maximum recommended
gate weight and length nor on gates with rising hinges or self closing hinges. Wrong selection of
motor will result in an unreliable operation and void your warranty..
Please Read This First!
Thank you for purchasing the E8 “do-it-yourself” automatic gate opener! When correctly installed
and properly used, your E8 Gate Opener will give you many years of reliable service.
The E8 Opener is designed for installation on a pull-to-open or push-to-open gate.
The E8 Gate Opener can be used on aluminum, chain link, farm tube, and wrought iron gates.
Use on solid surface gates is NOT recommended. Solid surface gates have a high resistance to
the wind. If the wind is strong enough, the operator will obstruct and stop.
The E8 Gate Opener accommodates extra transmitters, digital keypads, solar panels, push
buttons, automatic gate locks, and other access control products.
The E8 Gate Opener features an obstruction sensor. This feature makes the gate stop and
reverse open when it comes in contact with an obstruction. This sensitivity can be adjusted on the
main control board.
The E8 Gate Opener has an adjustable auto-close feature. After the gate reaches the fully open
position, it can be set to remain open up to 99 seconds before automatically closing. Pressing the
transmitter button at any time after the gate opens fully will cause it to close immediately.
OFF is the factory setting; meaning the gate will stay open until you press the transmitter
(or keypad, etc.) again. You can adjust this in the menu settings.
3
Important Safety Information
Because automatic gate operators produce high levels of force, consumers need to know the
potential hazards associated with improperly designed, installed, and maintained automated gate
opener systems. Keep in mind that the gate opener is just one component of the total gate
operating system. Each component must work in unison to provide the end user with
convenience, security, and safety.
This manual contains various safety precautions and warnings for the installer end user. Because
there are many possible applications of the gate operator, the safety precautions and warnings
contained in this manual cannot be completely exhaustive in nature. It does, however, provide an
overview of the safe design, installation, and use of this product.
CAREFULLY READ AND FOLLOW ALL SAFETY PRECAUTIONS, WARNINGS AND
INSTALLATION INSTRUCTIONS TO ENSURE THE SAFE SYSTEM DESIGN, INSTALLATION
AND USE OF THIS PRODUCT.
Because the E8 automatic gate opener is only part of the total gate operating system, it is the
responsibility of the installer and end user to ensure that the total system is safe for its intended
use.
For the Installer and End User
1. Attach the warning sign (included) to the gate to alert the public of automatic gate operation.
2. The gate is automatic and could move at any time, posing serious risk of entrapment. No one
should be in contact with the gate when it is moving or stationary.
3. Do not attempt to drive into the gate area while the gate is moving; wait until the gate comes
to a complete stop.
4. Do not attempt to “race the gate” while the gate is closing. This is extremely dangerous.
5. Do not allow children or pets near your gate. Never let children operate or play with gate
controls. Keep the remote control away from children and unauthorized users; store controls
where children and unauthorized users do not have access to them.
6. KEEP GATE SYSTEMS MAINTAINED. Always disconnect any power source from the opera-
tor before performing any maintenance.
7. To operate this equipment safely, YOU must know how to disconnect the operator for manual
gate operation.
8. Disconnect the operator ONLY when all power sources are DISCONNECTED and the gate is
NOT moving.
9. Make arrangements with local re and law enforcement for emergency access.
10. Distribute and discuss copies of the IMPORTANT SAFETY INFORMATION section of this
manual with all persons authorized to use your gate.
11. IMPORTANT: Save these safety instructions. Make sure everyone who is using or will be
around the gate and gate operator are aware of the dangers associated with automated gate
systems. In the event you sell the property with the gate operator or sell the gate operator,
provide a copy of these safety instructions to the new owner.
After Installation
4
Important Safety Information
To reduce the risk of injury or death:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Never let children operate or play with gate controls. Keep the remote control away from
children.
3. Always keep people and objects away from the gate. NO ONE SHOULD CROSS THE PATH
OF THE MOVING GATE.
4. Test the gate operator monthly.
5. Use the manual/emergency release only when the gate is not moving.
6. KEEP GATES PROPERLY MAINTAINED.
7. The entrance is for vehicles only. Pedestrians must use separate entrance.
8. The gate must be installed in a location that provides adequate clearance between it and ad-
jacent structures when opening and closing to reduce the risk of entrapment. Swinging gates
must not open into public access areas.
Owner should observe the following:
1. Do not cross the gate while it is operating.
2. Keep children away from the gate and the remote controls.
3. Test the system frequently and monitor the high and low speed of the system.
4. Practice the use of the emergency release key. This is crucial in the event that the system
does not work.
5. Place the WARNING signs prominently on the gate to warn pedestrian of the automatic gate
operation on your premises. It is your responsibility to post the warning signs on both sides
of the gate.
Installer should observe the following:
1. Make sure the gate weight and length does not exceed the maximum specications.
2. The gate design must be suitable for the installation of the auto gate system.
3. Ensure that the gate is installed on at, level ground and can move freely in both directions
along the entire swing of the gate. A properly balanced swinging type gate should NOT
swing open or swing close when no pushing or pulling force is exerted onto it.
4. Control panel box must be installed in the area where it is not easily damaged.
5. Do not change with parts or components not supplied by manufacturer.
6. Make sure all wiring is correct and in accordance with electrical bylaws and in good condition
before supplying the mains power to the control panel.
7. Remove all power when doing any maintenance including solar.
8. Ensure the control panel box is free from water leakage and insects to avoid short circuiting
of the control panel. Silicon off any holes (moth balls may also help in the prevention of
insects)
9. Never supply mains power directly to the DC motor
10. Transformer MUST be connected to mains power via RCD (residual current device).
11. Do not install the operating system if in doubt.
WARNING
5
Technical Specications
Supply voltage: 16vac Transformer or Solar 12v
Backup Battery: 12Vdc Lead acid
maintenance free (Electric optional)
Operating Voltage: DC 16-18V for normal speed
DC 6-10V for cushioning speed
Driving Method: Screw driven type
Max. Output Power: 80W per driver
Gear Box: Three-stage spur gear reducer
Operating Cycle: 13-19 seconds Per 90° (on AC power
only)
Max. Piston Stroke: 500mm
Max Piston Speed: 3cm/sec
Max. Weight of Gate: 250kgs (1.5mtr)
dependant on gate length
Max. Length of Gate: 4.2m per leaf (500mm)
Safety Clutch: Electronic current sensing,
high amp cut off
Electronic Controller: Micro-processor based
Remote Controller: 4 channel 433MHz
6
Kit Includes
Standard Packaging of the swing gate opener kit includes:
Single = 1 leaf Double = 2 leafs
Actuator Arm: 1 x for single or 2 x for double
Cardboard Template: 1 only
Primary Post Bracket: 1 x for single or 2 x for double
Secondary Post Bracket: 1 x for single or 2 x for double
Gate Bracket: 1 x for single or 2 x for double
Rubber Gate Stop: 1 only
Release Keys: 2 only
Primary Bracket Bolts: Not supplied (Single x 4 or Double x 8)
Secondary Bracket Bolts: 2 x for single or 4 x for double
Gate Bracket Bolts: 2 x for single or 4 x for double
Rear Mounting Bolts: 1 x for single or 2 x for double
Release Bolts: 1 x for single or 2 x for double
Small Bracket set (3): 1 only
Control Box: 1 only
Main Control Board
EGA-04: 1 only
Receiver: onboard
Remotes/fobs: 2
12v Battery: 1 only (if solar)
Regulator: 1 only (if Solar)
45Watt Solar Panel: 1 only (if Solar) with 10mtrs cable
+ mounting bracket
Transformer 16VAC: 1 only (if Electric)
Conduit: 1 small piece only
Cable: 6m for double kits
(across driveway for second actuator)
Junction box: 1 for double kit only
PLEASE NOTE:
POST BRACKET BOLTS AND CONTROL BOX MOUNTING BOLTS
ARE NOT SUPPLIED
7
Control Box
Actuator Arm with cardboard template
Caution Sign
Main Control board
Remotes Rubber Stop
12v Battery (solar) Regulator
(if Solar)
45watt Solar Panel
(if Solar)
Transformer
(if Electric)
Bracket Set
(3)
Release Key Gate Bracket Primary
Bracket
Secondary
Bracket
Gate Bracket
Bolts
Release Bolt Mounting Bolt P & S Bracket
Bolts
STANDARD KIT INCLUSIONS
8
OPTIONAL EXTRAS
Round Gate
Bracket Round Post
Brackets
Adjustable Hinge
Wireless Keypad Wired Keypad
Push ButtonWired Eyebeams
Keyed Push Button
(wireless or
wired available)
Long Range Receiver
Warning LIght
Push to open
Bracket
Electric Gate Lock
9
Single Swing Setup Example
Installations vary slightly on different types of gates
CAUTION
SIGN
GATE STOP
GATE BRACKET
ACTUATOR ARM
PRIMARY BRACKET
CONTROL BOX
SECONDARY
BRACKET
CABLE TO:
SOLAR PANEL
(10M CABLE
SUPPLIED)
OR TRANSFORMER
(CABLE NOT
SUPPLIED)
POWER CABLE
MOTOR 2 (MAIN)
CONDUIT
FENCE POST SET
IN CONCRETE
10
Tabla de contenidos
