Blumax GPS-4043 Manual de usuario

Bluetooth GPS Recorder

GPS-4043

User Manual

- 1 -

Contents

1. Before you begin............................................................................................................. 2

1.1 Note and Warning ��2

1.2 Introduction��3

1.3 Features��3

1.4 Applications��4

1.5 Appearance��4

1.6 Power Switch and Push Button��5

1.7 LED Display��6

2. Getting started.................................................................................................................7

2.1 Checking the package content��7

2.2 Getting Started��8

Step 1 Charging Your Battery��8

Step 2 Turning on the power switch (NAV / LOG)��9

Step 3 Connecting your PDA device with GPS-4043��9

Step 4 Loading your GPS mapping or routing software�� 12

Step 5 Starting the application �� 12

2.3 Helpful Tips��13

3. Using Photo Tagger software................................................................................... 14

3.1 Execute and install software utility Photo Tagger ��14

3.2 Google Earth��14

3.3 Software Utility - GPS-4043 Photo Tagger ��14

Appendix A. Specifications ............................................................................................15

Appendix B. locr GPS Photo.......................................................................................... 17

Appendix C. How to change battery...........................................................................18

Appendix D. Certification ................................................................................................19

Appendix E. Warranty Information............................................................................... 21

- 2 -

- 3 -

1. Before you begin

• Blumax Bluetooth GPS-4043 Recorder uses Lithium battery. If Blumax Bluetooth

GPS-4043 Recorder is used in temperature lower than -10°C or higher than 60°C, its

battery charging capability will decrease. Please leave the Blumax Bluetooth GPS-4043

Recorder far from heat or high temperature environment. In addition, do not expose your

Blumax Bluetooth GPS-4043 Recorder in temperature higher than 140°F/60°C. If you

do not follow these rules, the battery inside Blumax Bluetooth GPS-4043 Recorder may

overheat, explode or burn itself, and this will lead to very serious damage. The Lithium

battery inside the Blumax Bluetooth GPS-4043 Recorder should be recycled.

• While in the hospital, turning off the Blumax Bluetooth GPS-4043 Recorder is recom-

mended. Wireless GPS receiver may interfere with medical equipments which use radio

frequency.

• For a long period not using Blumax Bluetooth GPS-4043 Recorder, take out the bat-

tery and store it in dry/cool places.

• For safety, keep the Blumax Bluetooth GPS-4043 Recorder and all accessories out

of children’s reach.

• The manufacturer assumes no responsibility for any damages and loss resulting

from the use of this manual, or from deletion of data as a result of malfunction, dead

battery, or from misuse of the product in any way.

• Use only the supplied and approved accessories. Unauthorized accessories, modi-

cations or attachments could damage the Blumax Bluetooth GPS-4043 Recorder, and

may violate regulations governing radio devices.

• Use a dry, clean soft cloth to clean the unit. Do not use harsh cleaning solvents,

chemicals, or strong detergents.

• Do not attempt to open the Blumax Bluetooth GPS-4043 Recorder yourself. Unau-

thorized hacking may damage the unit, and void your warranty.

1.1 Note and Warning

- 2 -

- 3 -

This Blumax Bluetooth GPS-4043 Recorder features an all-in-one, cost-effective

portable GPS logging solution. With its on-board memory, it allows you to log your

routes by ways of time/ distance/ speed. Points of interest can also be recorded by

a push button. Through user friendly software utility, it shows your track on Google

Earth. This data logger is small and robust, ideal to carry everywhere for applica-

tions such as route tracking, mountain climbing or eet management.

1. MTK GPS chipset 51 channels.

2. 25+ hrs operation time.

3. Embedded with 32Mb memory for saving up to 150,000 way points.

4. Dual modes for both route recording and navigation.

5. Push to log for points of interest.

6. 3 recording methods: by time, by distance or by speed.

7. Tracks can be shown on Google Earth.

8. WAAS and EGNOS supported for better accuracy.

9. Support NMEA-0183 GGA, GSA, GSV, RMC, VTG, GLL.

10. Fully compliant with Bluetooth V1.2

11. Support NMEA compliant mapping software like TomTom, Route66…etc.

1.2 Introduction

1.3 Features

- 4 -

- 5 -

• Route recording

• Business trip expense management

• Fleet management

• Driving behavior monitoring

• Saving of Point of Interest

1.5 Appearance

1.4 Applications

1. DC jack (mini USB type)

2. Mode switch (Power off/

Navigation/ Navigation&log)

3. Bluetooth status LED (blue)

4. Battery status LED (red/green)

5. GPS status LED (orange) /

Push to log LED (blue)

6. Internal GPS antenna

7. Push Button

274

- 4 -

- 5 -

1.6 Power Switch and Push Button

Power Switch

Right (Off) Power off

Middle (NAV) Enable Navigation mode

Left (LOG) Enable Navigation + log mode

Push button

Push Push to log points of interest, LED blinks 3 times.

NAV

You can use the GPS-4043 Recorder as a Bluetooth

GPS receiver to navigate when you have a Bluetooth

enabled PDA/ Smartphone in your car. The logging

is off.

logger, navigation function is on as well.

Difference between NAV and LOG:

- 6 -

- 7 -

1.7 LED Display

The Blumax Bluetooth GPS-4043 Recorder has three LED lights, one is Blue-

tooth Status LED, the 2nd one is Battery Status LED, the 3rd one is GPS Status

LED/ Push to log LED. The status table of LED shows as follows:

CATEGORY SYMBOL COLOR STATUS FUNCTION

Bluetooth

Status LED Blue

Always on:

Bluetooth on, but not con-

nected to any Bluetooth

devices yet

Slowly blink-

ing:

Sleeping mode (1 time / 5

seconds)

Quickly blink-

ing:

Bluetooth is connected and

ready for data transmission

(1 time / 2 seconds)

Battery Sta-

tus LED

Red Blinking: The battery is too low

Green Light On: The battery is charging

Green Blinking: The battery is fully charged

GPS Status

LED

Orange

Always on: Acquiring satellites, GPS

position not x

Quickly

Blinking:

GPS position is xed, Navi-

gation

Blue

Quickly

Blinking:

LED blinks 3 times, Points of

Interest is recorded

Slowly

Blinking:

The memory space is too low

(20% left now)

Solid The memory is full and stop

- 6 -

- 7 -

2. Getting started

Congratulations on your purchase of the GPS-4043 Recorder with built-in Lithium

rechargeable battery.

Before you start using GPS-4043 Recorder, please make sure if your package

includes the following items. If any item is damaged or missing, please contact

your dealer at once.

2.1 Checking the package content

- 1x Bluetooth GPS-4043 Recorder

- 1x USB to mini-USB cable

- 1x DC cigarette lighter adapter

- 1x Lithium rechargeable battery

- 1x CD Tool (user manual, software utility)

- 1x User manual

*Unit package contents may vary depending on countries without prior notice.

*NOTE: The Cigarette Adapter can only be used to charge GPS-4043 Recorder.

Please don’t make use of it with devices other than GPS-4043 Recorder.

- 8 -

- 9 -

Please follow the procedure step by step.

Step 1 Charging Your Battery

To charge your GPS-4043 Recorder data logger, you have to plug your USB cable

into the power source. Charging time is about 3~4 hours and you can charge from

PC/ Notebook’s USB HOST or from cigarette-lighter in car.

For the 1st time you use the GPS-4043 Recorder, please charge battery until it is

full (the green LED blinks). The LED that represents the battery is the right-most

battery icon (shown in below).

2.2 Getting Started

• If the LED is red, that means battery power is critically low. Charge immediately.

• If the LED is green, that means battery is charging now.

• If the green LED is blinking, that means battery is fully charged.

LED,

represents

the battery

status

- 8 -

- 9 -

Step 2 Turning on the power switch (NAV / LOG)

Step 3 Connecting your PDA device with GPS-4043

Data record Power off

Navigation

Please refer to the user manual of PDA to enable the Bluetooth connectivity. If the

connection between your device and GPS-4043 Recorder is successful, the blue

LED of GPS-4043 Recorder will be blinking.

Below, we provide a common procedure of software installation to set up your

PDA. (For other PDA, the steps may be different. Bluetooth Manager is a popular

program used on Bluetooth device.)

NAV

You can use the GPS-4043

Recorder as a Bluetooth

GPS receiver to navigate

when you have a Bluetooth

enabled PDA/ Smartphone

in your car. The logging is

off.

LOG

In this mode GPS-4043

Recorder works as a pure

logger, navigation function

is on as well.

Difference between NAV and LOG:

Tabla de contenidos

Otros manuales de GPS de Blumax

Blumax

Blumax GPS-Tracker V1.0 Manual de usuario

Blumax

Blumax GPS-009 Manual de usuario

Blumax

Blumax GPS-4013 Manual de usuario

Blumax

Blumax GPS-4012 Manual de usuario

Manuales populares de GPS de otras marcas

Raven

Raven Cruizer II Manual

Hama

Hama 53118 Manual de usuario

Garmin

Garmin SOUNDER 125 Manual de usuario

Garmin

Garmin DEZL 580 Manual de usuario

Jigabot

Jigabot EX Manual de usuario

Pointer

Pointer Cellocator CelloTrack XT LTE Guía de instalación

Queclink

Queclink GV55LITE Manual de usuario

Voxson

Voxson Voxtrack GPS500 Manual de instrucciones

Garmin

Garmin ECHOMAP PLUS Manual de usuario

Starcom Systems

Starcom Systems Kylos Compact Manual de usuario

Garmin

Garmin 15 H Series Manual de usuario

Cobra

Cobra Marine MC 600Ci Manual de usuario

Cellocator

Cellocator CelloTrack T Manual de usuario

Enfora

Enfora Mini-MT GSM2228UG001 Manual de usuario

Magellan

Magellan eXplorist 100 Manual de usuario

LTE

LTE G50B Manual de usuario

Garmin

Garmin DEZL OTR500 Manual de usuario

SkyGolf

SkyGolf SkyCaddie SG1 Manual de usuario