Blue Diamond Multi-Purpose Cutter Guía

Multi-Purpose

Cutter

Operation and Parts manual

Brush Cutters

888-376-7027

Blue Diamond Attachments, LLC

September 2020

Pre-Delivery Checklist

The Dealer should inform the Purchaser of this product of the Warranty terms, provisions, and procedures that

are applicable. The Dealer and Purchaser should review the contents of the Operator’s Manual including safety

equipment, safe operation and maintenance, review the Safety Signs on the implement (and tractor if necessary),

and the Purchaser’s responsibility to train their operators in safe operation procedures.

• IMPLEMENTS: I have explained that a Safety Shield should be installed and maintained in good repair. If the

shield is not installed the purchaser accepts responsibility for any personal injury due to not having the shield.

• HYDRAULICS: I have made certain that the hydraulic supply pump, hoses, and motor is in good repair and

fastened securely in place to prevent injuries.

• MOUNTED IMPLEMENTS: I have explained that it is not possible to guard against thrown objects when

the cutter is lifted off the ground or operated in a vertical conguration, and that operator is responsible for

watching out for persons in the work area.

PRE-DELIVERY SERVICE

CHECK AND ADJUST OR LUBRICATE AS REQUIRED

Refer to this Manual for Details

Inspection Performed - Warranty and Safety Procedures Explained - Installation Complete

CUTTER

 Make Sure The Pump Motor And Adapter Bolts Are

Properly Tightened

 Make Sure The Blade Carrier Bolt Is Properly

Tightened And Cotter Pin Is In Place

 Make Sure The Two Blade Bolts Are Tight

 Make Sure The Blades Are Installed In Correct

Rotational Direction

 Review Procedure To Configure The Cutter In One

Of The Three Possible Configurations

Make Sure All Hardware Is Properly Tightened

 Retighten the tapered roller bearing in the pivot

arm after 15 minutes of initial use and again at 30

minutes. Recheck again before the next use.

I have thoroughly instructed the buyer on the above-described equipment. This review included the Operation and

Parts Manual content, equipment care, adjustments, safe operation, and applicable warranty policy.

Date__________________ Dealer Rep. Signature_________________________________________

The above equipment and Operator’s Manual have been received by me (the purchaser), and I have been

thoroughly instructed as to care, adjustments, safe operation, and applicable warranty policy. As the purchaser

I have read, understand, and take responsibility for the use of this attachment. I understand and

accept responsibility for the proper use of this cutter. I acknowledge this cutter is dangerous if not

used correctly or if the safety information is not followed.

Date__________________ Owner’s Signature_________________________________________

LUBRICATION & HYDRAULICS

Make Sure All Grease Joints Are Lubricated.

Check All Hoses And Coupling For Damage Or

Leaks.

CUTTER TO TRACTOR CONNECTIONS

Make Sure The Proper Hydraulic Connections Are

Available On the Tractor

SAFETY ITEMS

Make Sure Safety Shield Is Properly Installed

Make Sure Safety Decals Are Installed

 Review This Operator’s Manual

Cut Here to Remove Page or Make Copies of This Page

4Brush Cutters

888-376-7027

Blue Diamond Attachments, LLC

September 2020

Table of Contents

1. INTRODUCTION ........................5

1.1 Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2 Safe Operation .........................5

1.3 Intended Usage .........................5

1.4 Owner/Operator Manual Storage ...........6

1.5 Operator Orientation .....................6

1.6 Serial Number Location...................6

1.7 Product Improvements ...................6

1.8 Disposal of Equipment at End of Useful Life ...6

1.9 Unanswered Questions ...................6

2. SAFETY................................7

2.1 General ...............................7

2.2 Safety Alert Symbols .....................7

2.3 Safety Icon Nomenclature ................ .8

2.3.1 Personal Protection/Important

Information ...................... 8

2.3.2 Prohibited Actions .................8

2.3.3 Hazard Avoidance .................8

2.4 General Safety Instruction.................9

2.5 Training ..............................10

2.6 OSHA Training Requirements .............10

2.7 Federal Laws and Regulations ............11

2.8 Sign-Off Form .........................12

2.9 Operation Safety .......................13

3. SAFETY SIGNS AND INSTRUCTIONAL

LABELS ..............................14

3.1 General Information. ....................14

3.2 How to Install Replacement Safety Signs ....14

3.3 Safety Signs ..........................15

4. 4. OPERATION ..........................18

4.1 Operating Safety .......................18

4.2 Work Area Safety. ......................18

4.3 Tractor Requirements ...................19

4.4 Attaching to Tractor ....................19

4.5a Mowing Configuration ...................21

4.5b Mowing Configuration ................... 24

4.6 Detaching from Tractor ..................25

4.7 Cutter Checklist .......................25

4.8 Operation Checklist .....................26

4.9 Right of Way (Roadway) Mowing ..........26

5.TRANSPORTING .......................27

5.1 Transporting Safety (Road) ...............27

6.STORAGE .............................28

6.1 Storage Safety. ........................28

6.2 Placing In Storage ......................28

6.3 Removing From Storage ................28

7.SERVICE AND MAINTENANCE ...........29

7.1 Maintenance Safety. ....................29

7.2 Greasing .............................30

7.3 Blade Servicing .......................30

7.3.1 Blade Removal. ..................30

7.3.2 Blade Installation .................30

7.3.3 Blade Sharpening ................30

7.4 Blade Carrier Removal ..................30

7.5 Blade Carrier Installation .................30

7.6 Service Record ........................31

7.7 Welding Repairs .......................31

9. 8. PARTS ..............................32

10. 9. WARRANTY ..........................38

5Blue Diamond Attachments, LLCBrush Cutters

September 2020 888-376-7027

1. INTRODUCTION

1.1 Welcome

Standard Offset Configuration

Congratulations on your choice of a Blue Diamond

Attachments, LLC Multi-Purpose Cutter. This

equipment has been designed and manufactured to

meet the needs of discerning users.

The Blue Diamond Multi-Purpose Cutter is designed to

cut grass, weeds, and light brush.

Many features incorporated into this Multi-Purpose

Cutter are the result of suggestions made by

customers like you. Read this manual carefully to

learn how to operate the Multi-Purpose Cutter safely

and how to set it to provide maximum cutting

efficiency.

The offset mowers are designed for light-duty

applications such as weed, grass, and light brush up to

3” diameter. The cutters can be used to mow under a

fence line or it can be turned vertically to mow the

sides of hedgerows and tree lines.

The cutter uses a single spindle with two free-swinging

blades, which reduce the shock of impact when a

stationary object is contacted. A shear key in the input

shaft protects the motor from damage.

WARNING

Operating the Multi-Purpose Cutter without

the safety shield can result in physical

injury or death. Make sure the shield is

properly installed and in working condition

before operating the Multi-Purpose Cutter.

By following the operating instructions in conjunction

with a good maintenance program, your Multi-Purpose

cutter will provide many years of trouble-free service.

1.2 Safe Operation

Safe, efficient, and trouble-free operation of your

Multi-Purpose Cutter requires that you, and anyone

else who will be using or maintaining the unit, read

and understand the information contained within the

Owner’s Manual.

Use this manual for frequent reference and to pass on

to new operators or owners.

WARNING

Read And Understand Manual

To prevent personal injury or even death, be

sure you read and understand all of the

instructions in this manual and other related

OEM equipment manuals! The Multi-Purpose

Cutter, if not used and maintained properly, can be

dangerous to users unfamiliar with its operation. Do

not allow operating, maintaining, adjusting, or

cleaning of this Multi-Purpose Cutter until the

user has read this manual and has developed a

thorough understanding of the safety precautions

and functions of the unit.

This Multi-Purpose Cutter is designed for the specific

purpose of cutting grass, weeds, and light brush.

DO NOT modify or use this Multi-Purpose Cutter

for any application other than that for which it was

designed.

Offset mowers maintained or operated

improperly or by untrained personnel can be

dangerous; exposing the user and/or

bystanders to possible serious injury or death.

1.3 Intended Usage

Do not use this Multi-Purpose Cutter for any other

purpose than its intended use; cutting grass, weeds,

and light brush and an in-line or offset application.

6Brush Cutters

888-376-7027

Blue Diamond Attachments, LLC

September 2020

The Multi-Purpose Cutter can also be used in a

vertical configuration for mowing along hedge rows

and tree lines.

This unit WILL NOT work on a skid steer

machine.

WARNING

Using the cutter on a skid steer will void the

warranty and have the potential for serious

injury to the user or bystanders.

1.4 Owner/Operator Manual Storage

Always store the Owner/Operator manual and other

operating materials in the document storage tube.

1.5 Operator Orientation

The directions left, right, front, and rear, as mentioned

throughout this manual, are as seen from the tractor

operator’s seat and facing in the direction of travel.

1.6 Serial Number Location

The serial number decal is located on the top left

of the mounting plate.

Model Number ______________________________

Serial Number ______________________________

1.7 Product Improvements

Because Blue Diamond Attachments, LLC maintains

an ongoing program of product improvement, we

reserve the right to make improvements in design or

changes in specifications without incurring any

obligation to install them on units previously sold.

1.8 Disposal of Equipment at End of Useful

Life

The Blue Diamond Attachments, LLC Multi-Purpose

Cutter has been designed for the specific purpose of

cutting grass, weeds, and light brush. When this unit is

no longer capable of doing its designed purpose, it

should be dismantled and scrapped. Do not use any

materials or components from this unit for any other

purpose.

1.9 Unanswered Questions

If you have any questions not answered in this manual

or require additional copies or the manual is damaged,

please contact your dealer or:

Blue Diamond Attachments, LLC.

4512 Anderson Road

Knoxville, TN 37918

Phone: (888) 376-2027

Fax: (865) 246-2007

7Blue Diamond Attachments, LLC

888-376-7027

2. Safety

2.1 General

Safety of the operator and bystanders is one of the

main concerns in designing and developing a new

piece of equipment. Designers and manufacturers

build in as many safety features as possible. However,

every year many accidents occur which could have

been avoided by a few seconds of thought and a more

careful approach to handling the equipment.

Most work-related accidents are caused by failure to

observe basic safety rules or precautions. An accident

can often be avoided by recognizing potentially

hazardous situations before an accident occurs. As you

assemble, operate, or maintain the Multi-Purpose Cutter

(unit), you must be alert to potential hazards. You

should also have the necessary training, skills, and tools

to perform any assembly or maintenance procedures.

Improper operation and maintenance of this unit could

result in a dangerous situation that could cause injury

or death.

If you have any questions not answered in this manual

or require additional copies or the manual is damaged,

please contact your dealer or:

Blue Diamond Attachments, LLC.

4512 Anderson Road

Knoxville, TN 37918

Phone: 888-376-7027

Fax: 423-405-5904

WARNING

Do not assemble, operate, or maintain the

unit until you read and understand the

information contained in this manual.

Safety precautions and warnings are provided

in this manual and on the unit. If these hazard

warnings are not heeded, bodily injury or

death could occur to you or to other persons.

Blue Diamond Attachments, LLC cannot anticipate

every possible circumstance that might involve a

potential hazard. The warnings in this manual and on

the

unit are, therefore, not all-inclusive. If a method of

assembly, operation, or maintenance not specifically

recommended by us is used, you must satisfy yourself

that it is safe for you and for others. You should also

ensure that the unit will not be damaged or be made

unsafe by the methods that you choose.

The information, specifications, and illustrations in

this manual are based on the information that was

available at the time this material was written and can

change at any time without notice.

2.2 Safety Alert Symbols

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

This manual contains DANGERS, SAFETY

INSTRUCTIONS, CAUTIONS, IMPORTANT NOTICES,

and NOTES which must be followed to prevent

the possibility of improper service, damage to the

equipment, personal injury, or death. The following

keywords call the readers’ attention to potential

hazards.

Hazards are identied by the “Safety Alert Symbol”

and followed by a signal word such as “DANGER”,

“WARNING”, or “CAUTION”.

DANGER

Indicates an imminently hazardous situation which,

if not avoided, will result in death or serious injury.

This signal word is limited to the most extreme

situations.

WARNING

Indicates a potentially hazardous situation which, if

not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

NOTICE

Indicates that equipment or property damage can result

if instructions are not followed.

SAFETY INSTRUCTIONS

Safety instructions (or equivalent) signs indicate

specic safety-related instructions or procedures.

Note: Contains additional information important to a

procedure.

Brush cutters

September 2020

8Brush Cutters

888-376-7027

Blue Diamond Attachments, LLC

September 2020

2.3 Safety Icon Nomenclature

Pictorial icons signal a type of

hazard and warn of personal

protection issues, prohibited actions,

and hazard avoidance.

2.3.1 Personal Protection/

Important Information

Read the manual

Maintenance procedure

Damaged hazard label

Eye protection

Fire extinguisher

First aid kit

Hand protection

Head protection

Hearing protection

Inspect equipment

OEM

OEM parts only

Protective shoes

Remove key

Set parking brake

STOP Stop engine

THINK

SAFETY! Think safety

Transmission in park

Use proper support

Use proper tools

Use two people when

lifting heavy objects

Visibility

Rollover protection

Wear seat belt

Weight rating

Chemical flushing kit

2.3.2 Prohibited Actions

Do not alter or modify

Use proper tools

Do not weld

No alcohol

No drugs

No smoking

No young children

No riders

2.3.3 Hazard Avoidance

Crush hazard

Crush hazard (chock

wheels)

Crush hazard (foot)

Defective or broken part

Entanglement hazard

Explosive force hazard

Explosive separation

hazard

Fall hazard

Fire hazard

Cutter blade contact

hazard (hand)

Cutter blade contact

hazard (foot)

Lifting hazard

Cutting hazard

Pinch point hazard

Projectile hazard

Rollover protection

Safety alert symbol

Safety shields

Sharp object hazard

Slipping injury

0Tire pressure

Tripping injury

9Blue Diamond Attachments, LLC

Brush Cutters

September 2020 888-376-7027

2.4 General Safety Instruction

The owner/operator is responsible for the SAFE use

and maintenance of the Multi-Purpose Cutter. Make

sure anyone who is operating, maintaining, or working

around the Multi-Purpose Cutter is familiar with the

operating and maintenance procedures and related

SAFETY information contained in this manual. This

manual will take you step-by-step through your

working day and alerts you to all good safety practices

that should be used while using the Multi-Purpose

Cutter.

In addition to the design features of the Multi-Purpose

Cutter, including safety signs, accident prevention is

dependent upon the awareness, concern, prudence,

and proper training of the people involved in the

operation, maintenance, and storage of the Multi-

Purpose Cutter.

In addition to this safety section, refer also to safety

messages and instructions in each of the appropriate

sections of the Multi-Purpose Cutter manual.

These general safety instructions apply to the overall

use and maintenance of the Multi-Purpose Cutter.

More specific instructions on safety are found in the

operation, maintenance, and storage sections of this

manual. Refer to these sections before performing

any of these tasks.

WARNING

Failure to comply with the following safety

instructions can and will result in serious injury and

possibly even death if they are not understood and

followed.

Read and Understand Manual

To prevent personal injury or even

death, be sure you read and understand

all of the instructions in this manual and other

related OEM equipment manuals! The

Trailblazer Multi-Purpose Cutter, if not used and

maintained properly, can be dangerous to

users unfamiliar with its operation. Do not

allow operating, maintaining, adjusting, or

cleaning of this Multi-Purpose Cutter until the user

has read this manual and has developed a

thorough understanding of the safety precautions

and functions of the unit.

This Multi-Purpose Cutter is designed for the

specific purpose of cutting grass, weeds, and

light brush. DO NOT modify or use this Multi-

Purpose Cutter for any application other than

that for which it was designed.

Brush cutters maintained or operated improperly,

or by untrained personnel, can be dangerous;

exposing the user and/or bystanders to

possible serious injury or death.

WARNING

Provide User with Literature Trailblazer

Multi-Purpose Cutter owners must provide

operator instructions to anyone using the

Multi-Purpose Cutter before use, and at least

annually thereafter. Refer to “2.6 OSHA

Training Requirements” on page 13.

Stay Clear: Clear the area of people,

especially small children, before using

the Multi-Purpose Cutter. Under no

circumstances should young children be allowed

to work with or around the Multi-Purpose Cutter.

Impaired User Hazard : Do not

attempt to assemble, operate, or

maintain this Multi-Purpose Cutter

under the influence of drugs or alcohol. Consult

your doctor before using this Multi-Purpose

Cutter while taking prescription medications.

Crush Hazard

Do not allow anyone to ride on the

tractor or the Multi-Purpose Cutter.

Falling or crushing hazards can result in severe

injuries or death.

Falling Hazard

Do not allow riders on the hitch,

tractor, or cutter at any time.

Falling can result in severe injuries or death.

No Unauthorized Modi ications Do

not modify the Multi-Purpose Cutter

or safety devices. Do not weld on the

Unauthorized modifications may impair its function

and safety. Personal injury or death can result

from unauthorized modifications.

If the Multi-Purpose Cutter has been altered in any

way from the original design, Trailblazer does not

accept any liability for injury or warranty.

Damaged Parts Hazard: Do not use the

Multi-Purpose Cutter if any parts are

damaged. If the Multi-Purpose Cutter has a

defect, immediately stop using it and remedy the

problem before continuing.

Thrown Objects Hazard: The Multi-

Purpose Cutter can throw objects up to

300 feet. To avoid serious injury or death:

Keep all thrown object shielding in place.

Inspect area for potential thrown objects before

cutting.

Do not operate the Multi-Purpose Cutter with

the deck raised.

10Brush Cutters

888-376-7027

Blue Diamond Attachments, LLC

September 2020

CAUTION

The following safety instructions are provided to

help prevent potential injury. Not following these

instructions may lead to injury.

Personal Protection Equipment

When using this Multi-Purpose Cutter, wear

appropriate personal protective equipment.

This list may include, but is not limited to:

• Protective shoes with slip resistant soles

• Protective goggles, glasses, or face shield

• Protective clothing and gloves

• Safety vest (when operating near roads)

• Hearing protection

Ear Protection

Wear suitable ear protection during prolonged

exposure to excessive noise.

Hearing Loss

Prolonged Exposure To Loud Noise May

Cause Permanent Hearing Loss!

Working environments with noise-producing

equipment can cause partial to permanent hearing

loss. We recommend using hearing protection any

time noise levels exceed 80 decibels (dB). Noise

levels over 85 dB, on a long-term basis, can cause

severe hearing loss. Noise levels over 90 dB over a

period of time can cause permanent and even total

hearing loss.

Hearing loss from loud noise is cumulative over a

lifetime without hope of natural recovery.

Crush Hazard

The tractor should be equipped with a

Roll Over Protective Structure (ROPS)

and a seat belt. A crushing hazard can occur if the

driver is ejected from the seat while the tractor is in

motion. Fasten the seat belt whenever the tractor is

moving.

SAFETY INSTRUCTIONS

The following safety instructions are provided to

help prevent injury or limit equipment damage.

AR Safety Signs

Replace any missing or hard-to-read safety

signs or instructional labels. Use care when

washing or cleaning the Multi-Purpose Cutter.

Replacement safety sign locations and part numbers

are provided in this manual and are available from

an authorized dealer parts department or the factory.

First Aid Kit

Have a rst aid kit available for use should

the need arise and know how to use it.

Fire Extinguisher

Have a re extinguisher available for use

should the need arise and know how to use it.

THINK

SAFETY! Think SAFETY!

Work SAFELY!

2.5 Training

Anyone who will be using and/or maintaining the

cutter must read, clearly understand, and follow ALL

safety, operation, and maintenance information

presented in this manual, other related OEM manuals,

and the safety signs

If you do not understand any information in this

manual, see your dealer or contact Blue Diamond

Attachments, LLC before proceeding.

Do not use or allow anyone else to use this cutter until

all information has been reviewed. Annually review

this manual before the season start-up.

Make periodic reviews of SAFETY and OPERATION

of the cutter a standard practice. An untrained

operator is not qualified to use this cutter.

2.6 OSHA Training Requirements

The following training requirements have been taken

from Title 29, Code of Federal Regulations Part

1928.57 (a) (6). www.osha.gov.

Operator instructions. At the time of initial assignment

and at least annually thereafter, the employer shall

instruct every employee who operates an agricultural

tractor and implements in the safe operating practices

and servicing of equipment with which they are or will

be involved, and of any other practices dictated by the

work environment.

Tabla de contenidos

Otros manuales de Cortador de Blue Diamond

Blue Diamond

Blue Diamond 403125 Manual de programación

Blue Diamond

Blue Diamond 91566-99427 Manual de usuario

Manuales populares de Cortador de otras marcas

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manual de usuario

Makita

Makita DCS552 Manual de usuario

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manual de usuario

Makita

Makita 4112HS Manual de usuario

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manual de usuario

Hitachi

Hitachi CM 4SB2 Guía de solución de problemas

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manual de usuario

GCC Technologies

GCC Technologies AFJ-24S Manual de usuario

DeWalt

DeWalt XR LI-ION DCS350N Manual de usuario

Baudat

Baudat ES1 Manual de usuario

Mafell

Mafell ZAF 200 Guía

Makita

Makita 4100NH Manual de usuario

Formax

Formax FD 574 Manual de usuario

EINHELL

EINHELL TE-MA 1500 Manual de usuario

Husqvarna

Husqvarna Cut-n-Break K 760 Manual de usuario

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manual de usuario

TRI tool

TRI tool 301A Manual de usuario

Roller

Roller King 1 1/4 Manual de usuario