Blue Bamboo H50 Manual de usuario

H50 Terminal

Quick Installation Guide

Version 1.2

- 1 -

Table of Contents

Powering the H50 Terminal………………………………………………….2

Installing and Charging the Battery………………………………………..3

Loading Paper………………………………………………………………….5

Installing the Communication Module……………………………………..6

Using Smart Cards and Magnetic Stripe Cards…………………………..6

Cleaning the H50 Terminal……………………………………………………7

Using the H50 Terminal………………………………………………………..8

FCC Statement：

The antennas used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not be

co-located or operating in conjunction with any other antenna or transmitter

This device complies with part 15 of the FCC Rules. Operation is

subject to the fol-lowing two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference re-ceived, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to pro-vide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses and can

radi-ate radio frequency energy and, if not in-stalled and used in accor-

- 2 -

dance with the in-structions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equip-ment does cause harmful in-

terference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the fol-lowing measures: —Reorient or

relocate the receiving antenna. —Increase the separation between the

equip-ment and receiver. —Connect the equipment into an outlet on a cir-

cuit different from that to which the re-ceiver is connected. —Consult the

dealer or an experienced radio/ TV technician for help.

the user that changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

- 3 -

Powering the H50 Terminal

The H50 terminal requires the battery to be installed for operation, whether

running from the power adaptor or the C50 cradle. It is recommended to

fully charge the battery immediately after unpacking the H50.

Use the following procedure to connect the H50 terminal to a groundedAC

power outlet (refer to the “C50 Users Guide” for information on the cradle):

1. Insert the power adapter into the terminal’s serial port (Figure 1) or

insert the terminal into the cradle (Figure 2).

2. Plug the power adapter into a groundedAC power outlet.

Figure 1 Connect the terminal’s power adaptor

Figure 2 Insert the terminal into the C50 cradle

- 4 -

Installing and Charging the Battery

The H50 terminal uses a Li-ion battery with internal logic to prevent both

overcharging and undercharging. Use the following procedure to install

and charge the battery:

1. Install the battery into the slot (Figure 3). A new H50 terminal may

have a battery pre-installed and require removal of the contact guard.

2. Connect the terminal to a power source as described on Page 2.

Complete charge time is approximately 3 hours.

3. To determine the battery charge state, turn on the terminal. Charge

status is indicated on the right of the LCD. Five bars indicate a full

charge.

Note:It is recommended that the battery receive a periodic full discharge.

To ensure a full discharge, use the unit until the battery is fully drained.

Note: Conserve battery power by turning the H50 terminal off when not in

use. If the terminal is not used frequently, remove the battery to maintain its

performance.

Figure 3 Installing the battery

- 5 -

Loading Paper

Use the following procedure to load paper into the H50 terminal:

1. Lift open the paper door (Figure 4).

2. Place the holder into the paper roll so paper feeds from under the roll.

3. Pull the end of the paper roll over the printer.

4. While holding the end of the paper roll, close the paper cover. You will

hear the paper cover click when properly latched.

5. Tear off the excess paper.

Note: The printer door is hinged, it is not necessary to remove it from the

terminal.

Figure 4 Open the print cover

- 6 -

Installing the Communication Module

Use the following procedure to install or change the communication module

in the H50 terminal:

1. Turn off the terminal.

2. Turn the terminal over (Figure 5).

3. If a module is currently in place, remove the screws to unlock and

remove the module.

4. Insert the module to be installed into the slot.

5. Use the screws to lock the module.

Note: It is recommended that only certified technicians install or exchange

the module. Please contact your distributor or service provider.

Figure 5 Installing the Module

GPRS Module

Modem Module

- 7 -

Using Smart Cards and Magnetic Stripe Cards

Use the following procedure to process a smart card:

1. Make sure the metal contact is facing up and toward the terminal body.

2. Insert the card into the H50 terminal’s smart card slot (Figure 6).

3. Leave the smart card in the reader until the transaction is complete.

Premature removal voids the transaction.

4. Remove the smart card once the terminal screen instructs you to.

Figure 6 Smart Card Reader

Use the following procedure to swipe a magnetic stripe card:

1. Make sure the magnetic stripe faces printer.

2. Slide the card all the way through the slot on the right-side of the ter-

minal, starting on either end, in one smooth motion (Figure 7).

3. Follow standard operating procedures to complete the transaction.

- 8 -

Figure 7 Magnetic Stripe Reader

Cleaning the H50 terminal

Use the following procedure to clean the casing and the printer mechanism

of the H50 terminal:

1. Apply alcohol or an alcohol-based cleaner to a clean, soft,

non-abrasive, and low-lint cloth. Carefully wipe the entire terminal.

2. The magnetic and smart card readers do not require regular mainte-

nance. For card reader service, please contact your distributor or ser-

vice provider.

3. As needed, use anti-static compressed air to clean in and around the

printer mechanism.

WARNING: Do not use thinner, acetone, trichloroethylene, ketone-based

solvents or other chemicals that can deteriorate plastic or rubber parts.

Do not spray cleaners or other solutions directly onto the keypad or dis-

play. Do not attempt to clean card readers, doing so may void your war-

ranty.

- 9 -

Using the H50 terminal

The following warnings are for your safety and that of your equipment.

For a full version of the H50 Installation Guide, please visit our website at

www.bluebamboo.com

WARNING:

zDo not use an ungrounded power adapter, extender cable, or

AC outlet.

zDo not disassemble the AC adapter. Only qualified technicians

may service the adapter.

zThe AC adapter is for indoor use only; do not expose to rain or

snow.

zDo not immerse the AC adaptor or the terminal in fluid.

Otros manuales para H50

Tabla de contenidos

Otros manuales de Terminal táctil de Blue Bamboo

Blue Bamboo

Blue Bamboo CT100 Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario