Blodgett XCEL-50EC Manual de usuario

L-920

Rev B

8-01-10

Page 1 of 2

Adjusting the T-Latch on the

Blodgett XCEL-50EC Oven for KFC

Tools Supplied:

C-shaped adjustment gauge

There are two parts to the T-latch:



Base with set screw



T-latch

Returning the T-Latch to Factory Settings

Use this procedure when installing a new gasket

Failure to follow the steps below may

result in damage to the oven and/or door

handle.

When installing a NEW door gasket,

use the C-shaped gauge to set the T-latch back

to the original factory setting. The T-latch must

be returned to the factory setting because if the

door seal is too tight the gasket may be

damaged by over-compression. If the door seal

is too loose, the oven may leak excessively

during the clean cycle and the door switch may

not operate properly.

1. With the door open, place the C-shaped

adjustment gauge over the T-latch. See

Figure 1a. Make sure the legs of the gauge

are touching the face of the oven.

2. If the end of the latch sits in the notch and

hits the edge of the notch when the gauge is

slid up or down, it is properly adjusted.

Figure 1a and 1b

3. The door gasket on the Blodgett XCEL-50EC

Grilled Chicken oven may shrink slightly as it

ages. Therefore, it may be necessary to adjust

the T-latch for the door handle to reduce

leakage during the clean cycle and extend the

life of your gasket. Use the following procedure

to adjust the T-latch on the XCEL-50EC oven.

C-shaped

adjustment

gauge

Be sure end of T-latch sits inside

the notch in the C-shaped gauge

Rubber boot removed from

later version of T-Latch

L-920

Rev B

8-01-10

Page 2 of 2

Adjusting the T-Latch

Use this procedure as the gasket changes over

time.

Figure 2

1. The T-latch is held in place by a set screw

and a jam nut. Using a 13mm wrench,

loosen the jam nut by turning to the left or

counter-clockwise. See Figure 3.

Figure 3

Using a 3/32” Allen wrench, loosen the set

screw on top of the T-latch base. Turn the

set screw 4 full turns.

Figure 4

3. The T-latch has a flat side. See Figure 5. Turn

the T-latch ½ of full turn, or 180°, clockwise to

tighten the door seal. NOTE: When a turn is

completed the flat side of the T-latch must be

facing up, and another one down.

Figure 5

4. Use an Allen wrench to tighten the set screw on

the top of the base.

5. Use a 13mm wrench to tighten the jam nut.

6. Only change ½ of full turn, or 180°, at a time

with

the maximum turns inward being

two

. Test the oven through a clean cycle. If over

time, the door leaks excessively ( an amount

more than what can be contained in the gutter )

during the clean cycle, repeat steps 1-6 to

readjust the T-latch.

Do not adjust the T-

latch in more than two full turns (four ½

turn adjustments) or damage to the door

handle may occur.

Use the C-shaped gauge

to verify if the T-latch is too short. See Figure 6.

When the T-latch has been adjusted in to the

point where it no longer reaches the bump on

the C-gauge, it is time to replace the gasket.

See Figure 6.

Figure 6

T-latch

T-latch base

One of two

flat sides

of T-Latch

Bump on C-Gauge

Otros manuales para XCEL-50EC

Otros manuales de Horno de Blodgett

Blodgett

Blodgett MT3255E Manual del propietario

Blodgett

Blodgett COS-6 Manual de usuario

Blodgett

Blodgett MT3870 Manual de usuario

Blodgett

Blodgett MT3255 Series Manual de instalación y funcionamiento

Blodgett

Blodgett XR8-G Manual de usuario

Blodgett

Blodgett 1415 Manual del propietario

Blodgett

Blodgett CONVEYOR OVEN MT1820E Manual de usuario

Blodgett

Blodgett COS-6 Manual de usuario

Blodgett

Blodgett BCX-14E Manual de usuario

Blodgett

Blodgett 1415 Manual de usuario

Blodgett

Blodgett Mark V Manual de usuario

Blodgett

Blodgett 901 Double Manual de usuario

Blodgett

Blodgett SG2136 E & G Guía de aplicación

Blodgett

Blodgett CTBR-AP Guía

Blodgett

Blodgett BCX-14G Manual de programación

Blodgett

Blodgett S1820G Series Manual de usuario

Blodgett

Blodgett S1828E Manual del propietario

Blodgett

Blodgett 951 Base Manual de usuario

Blodgett

Blodgett BE3240 Manual

Blodgett

Blodgett CONVEYOR OVEN MT1820E Guía de aplicación

Blodgett

Blodgett COS-20E Manual

Blodgett

Blodgett 901 Base Guía de aplicación

Blodgett

Blodgett SHO-E Manual de usuario

Blodgett

Blodgett BE2136 DOUBLE Manual de usuario

Manuales populares de Horno de otras marcas

Bosch

Bosch HVA531NS0 Manual de usuario

Electrolux

Electrolux EOF6P46X Manual de usuario

NEFF

NEFF B44S32 5GB Series Manual de usuario

Combi

Combi BLODGETT BC142GDS Manual de usuario

AEG

AEG COMPETENCE 311704300 Manual de usuario

Falcon

Falcon DOMINATOR PLUS G3106 Series Guía del usuario

Rational

Rational SCC WE 61G Manual de usuario

Smeg

Smeg DOSPA38X Manual de instalación y operación

Electrolux

Electrolux air-o-convect 20 GN 2/1 Manual de usuario

Miele

Miele HR 1954-2 Manual de usuario

KHIND

KHIND OT50 Manual de usuario

Henny Penny

Henny Penny Smoker Box Manual de usuario

Lang

Lang ECOD-AP Manual de usuario

AEG

AEG BEK455310M Manual de usuario

Frigidaire

Frigidaire FNGE90JGR Manual de usuario

Hotpoint

Hotpoint FE9 S831 JSH IX Manual de usuario

GE Advantium SCB2000 Manual de usuario

AEG

AEG DE401301DM Manual de usuario