Blink Marine Keypad Pro Series Instrucciones de montaje
The Identifier 18 --> Default Keypad ID (cannot be changed)
EF --> Message is made addressable in PDU Format
FF --> broadcast messages to no specific destination address
21 --> Source address of the keypad default
h --> hexadecimal value
Ext means that the message format is 29 bits instead of 11 bits.
The Identifier is basically a CAN Id which in this case has a source address (21 - keypad) ,
destination address (FF - any) --> Sending a message FROM the keypad TO the control unit
In case of Identifier 18EF2100h where destination address (21 - Keypad) , source address (00
- control unit) --> Sending a message TO the keypad FROM the control unit.
You can change the Destination address and Source address as you like.
The default keypad address is 21h.
Blink Keypad
Pro Series Tips
Keypad Basics
WWW.MURCAL.COM
CONTACT
(661) 272-4700
@MURCALINC
Difference between a J1939 and a
CANOpen in Blink Keypads:
CANOpen J1939
Identifier length 11 bit 29bit
Baud rate
available value
125kbit/s
250kbit/s
500kbit/s
1000kbit/s
250kbit/s
500kbit/s
CAN address
available range 01h – 7Fh (1-127) 01h – FDh (1-253)
LED indicator colors
Red
Green
Blue
Orange
Cyan
Magenta
White/light blue
Red
Green
Blue
Yellow
Cyan
Magenta
White/light blue
Orange
Lime
WWW.MURCAL.COM
CONTACT
(661) 272-4700
@MURCALINC
CANOpen J1939
LED indicator state
OFF
Solid ON
Blink
Alternate blink between
two colors
LED/Backlight
brightness level 00h-3Fh (0 – 100%) 00h – 3Fh (0 – 100%)
Backlight colors
Address claim at boot Not available Available on request
Heartbeat Available on request
(10ms – 65s)
Available on request
(50ms – 2540 ms)
OFF
Solid ON
Blink
Alternate blink between
two colors
Red
Green
Blue
Yellow
Cyan
Magenta
White/light blue
Orange
Lime
Red
Green
Blue
Yellow
Cyan
Magenta
White/light blue
Orange
Lime
WWW.MURCAL.COM
CONTACT
(661) 272-4700
@MURCALINC
CANOpen J1939
Keys message periodic
transmission
Available on request
(10ms – 65s)
Available on request
(50ms – 2540 ms)
Message
transmission type
Event-driven
Synchronous
Reset to the factory
settings
Event-driven
YES NO
If a key is pressed on the keypad, does it send out multiple CAN messages as long as the
button is pressed or just one message per press?
The message is transmitted when the key changes its status: e.g., until you keep pressed a key one message is
transmitted, when you release it another message is transmitted.
If no keys are pressed are there any messages being sent?
If the transmission is set on-event, no message is transmitted. If you set the periodic transmission or the heartbeat,
a periodic message is transmitted regardless a key is pressed or not.
What is the default J1939 speed setting? Is it 250 kbit/s or 500 kbit/s? What is the
industry standard?
The default baud rate value is 250kbit/s.
If I send a message to the keypad is there an acknowledgment reply?
In our firmware in J1939 no acknowledgment reply is transmitted.
FAQs
WWW.MURCAL.COM
CONTACT
(661) 272-4700
@MURCALINC
Otros manuales de Teclado de Blink Marine
Blink Marine
Blink Marine PKP2600SI CANopen Manual de usuario
Blink Marine
Blink Marine PKP-2200-SI Manual de usuario
Blink Marine
Blink Marine PKP-2400-LI Manual de usuario
Blink Marine
Blink Marine PKP2500SI Manual de usuario
Blink Marine
Blink Marine PKP-2400-SI Manual de usuario
Blink Marine
Blink Marine CANopen PKP3500SI Manual de usuario
Blink Marine
Blink Marine PoweKey PRO 2200 Manual de usuario
Blink Marine
Blink Marine PowerKey 1000 Manual de usuario
Blink Marine
Blink Marine PKP2600SI CANopen Manual de usuario
Blink Marine
Blink Marine PKP-1500-LI Manual de usuario
