Blackburn Delphi Manual de usuario

TABLE OF CONTENTS TABLE OF CONTENTS

ENGLISH

Introduction 1

Warnings and Cautions 2

Care and Maintenance 3

Parts of your Blackburn Delphi Cycle Computer 4

Resetting the Computer to its Default Settings 5

Shipping and Sleep Modes 6

Changing the Battery in the Blackburn Delphi Cycle Computer 7

Installing the Computer on your Bike 9

Keys and their Functions 15

Sections of LCD Display 18

Basic Operation 23

Bike One/Bike Two Setting 27

Program Wheel Size, Units and Chronograph 28

Program Odometers 36

Program Time of Day 38

Operating the Ride Time and Total Time Chronographs 41

Starting Stopping and Clearing the Chronograph and Memory 42

Clearing Maximum Speed or Maximum Cadence Only 43

Technical Data 44

Warranty and Repair 46

Blackburn_2/3_Manual 8/3/05 10:00 AM Page 2

INTRODUCTION WARNINGS AND CAUTIONS

ENGLISH

Congratulations on your purchase of a new Blackburn Delphi Cycle Computer. Blackburn Delphi

computers are among the most advanced cycle computers available in the market today.

Designed to meet the needs of serious cyclists, Delphi cycle computers offer a wide range of

advanced features including wireless operation, ECG accurate wireless heart rate and

ultra-accurate altimeter functionality. Blackburn has gone to great expense to assure these are

the best cycle computers you can buy. We are so sure of this, each unit we make is covered by a

limited LIFETIME WARRANTY against any defects in materials or workmanship. See Page 46 for

a complete description of the Bell Sports Limited Warranty.

This manual is an integral part of your Blackburn cycle computer. Please read it carefully and

use it while performing the initial programming and operating of the unit. After you are fully

familiar with all of the features and functions of your Blackburn cycle computer, put this manual

in a safe location for future reference.

WARNING—Blackburn cycle computers and heart rate monitors are training and fitness tools.

Before beginning any exercise program, consult your doctor to discuss your exercise plans.

WARNING—Do Not divert your attention from the road ahead to operate your cycle computer

at any time. We also strongly suggest you wear a Bell or Giro helmet any time you ride your bike.

CAUTION—Blackburn cycle computers are sophisticated electronic instruments. Blackburn

recommends this unit only be installed by a qualified Blackburn retailer. Failure to read the

instructions may result in damage caused by improper installation and may void the warranty. If

you are unsure about how to properly perform any aspect of the assembly, installation or

operation of your Blackburn cycle computer, please contact your local Blackburn retailer.

CAUTION—This unit is designed to be water resistant under normal riding conditions. It should

not be immersed in water. It should not be left attached to the bike if the bike is being

transported on an automobile.

CYCLE COMPUTER

Blackburn_2/3_Manual 8/3/05 10:00 AM Page 4

CARE AND MAINTENANCE PARTS OF YOUR BLACKBURN DELPHI

CYCLE COMPUTER

ENGLISH

Blackburn cycle computers contain many delicate electronic components which may be

damaged by excessive exposure to heat, shock or general abuse. Treated with care, your cycle

computer is capable of delivering many years of reliable service. Improper care and handling, or

damage caused by abuse or neglect, will void your Blackburn Warranty.

NEVER—Leave your computer in your car on hot days.

NEVER—Store your Blackburn cycle computer in a plastic or other non-breathable container.

FACE OF COMPUTER

WHEEL MAGNET

ZIP-TIES

WIRED SPEED BRACKET

WIRED SPEED & CADENCE

BRACKET WITH CADENCE SENSOR

BRACKET SLEEVE

CYCLE COMPUTER

Blackburn_2/3_Manual 8/3/05 10:00 AM Page 6

RESETTING THE COMPUTER TO ITS

DEFAULT SETTINGS SHIPPING AND SLEEP MODES

ENGLISH

On the bottom of the computer unit, to the upper right of the battery door is a small hidden

RESET key. Pressing this key with a toothpick or other small pointed object will reset all

programmed values to their default values and reset the microprocessor. This may also be

accomplished by removing and reinstalling the battery.

CAUTION—Pressing the RESET key will automatically clear any information from the units’memory.

SHIPPING MODE—Your new Blackburn Delphi computer comes to the dealer in

SHIPPING MODE. In this mode the LCD display is totally blank. This is done

to extend the battery life. Press any key to wake the unit up and advance to

the default display mode.

NOTE: It is possible the unit will not come to you in SHIPPING MODE if it

has been previously activated. This should not have an adverse impact

on the life of the battery.

SLEEP MODE—If no speed information is seen for a period of approximately

5-minutes the unit goes into its SLEEP MODE. In SLEEP MODE the display

will show the current Time of Day, Chronograph (RT or TT) and Units (Miles

or Kilometers) settings.

CYCLE COMPUTER

RESET BUTTON

Blackburn_2/3_Manual 8/3/05 10:00 AM Page 8

CHANGING THE BATTERY IN THE BLACKBURN

DELPHI CYCLE COMPUTER CHANGING THE BATTERY IN THE BLACKBURN

DELPHI CYCLE COMPUTER

ENGLISH

Blackburn Delphi computers are powered by a CR2032 3v Lithium Battery. Under normal

conditions, this battery should last approximately one year.

REPLACING THE COMPUTER BATTERY

1. Using a coin, turn the battery door counter clockwise until the door comes free.

2. Take care not to damage the O-ring seal for the battery compartment and carefully remove

the old battery.

3. Place a new battery in the battery compartment with the positive (+) side toward the

battery door. Be extremely careful not to bend the battery contact when inserting a new

battery.

4. Place the battery door over the opening and tighten it down by using a coin and turning in

a clockwise direction.

5. If the O-ring has been damaged, replace it before reinstalling the battery door.

CAUTION—Extreme care should be taken when replacing the battery to ensure the unit remains

fully water resistant. Failure to properly replace the battery and correctly seal the unit may cause

the unit to become damaged and may void the warranty.

ALWAYS—Check the batteries if you are experiencing problems with your computer. Most

problems experienced with the operation of this unit are the result of dead or dying batteries.

CYCLE COMPUTER

Blackburn_2/3_Manual 8/3/05 10:00 AM Page 10

INSTALLING THE COMPUTER ON YOUR BIKE INSTALLING THE COMPUTER ON YOUR BIKE

ENGLISH

The Delphi 2.0 uses a single wired sensor attached to the front fork.

1. Attach the front wheel sensor to either fork blade using the zip-ties

provided. Snug up the zip-ties but do not fully tighten them.

2. Attach the spoke magnet to a spoke on the same side of the wheel as

the sensor. Tighten the attachment screw just enough to hold the

magnet in place but loose enough so that it is still movable.

3. Adjust the position of the sensor and magnet so they are in proper

alignment as shown in the drawing and tighten the zip-ties and

magnet.

NOTE: The magnet should pass 1-3mm away from the sensor. The closer you

can get the magnet to the sensor the better.

INSTALLING WIRED FRONT WHEEL SPEED SENSOR AND BRACKET

(CONTINUED)

4. Route the remaining wire and bracket up the fork securing it with tape. Excess wire

should be wrapped around the brake cable housing until there is just enough slack

remaining to allow the bracket to be attached to the handlebars. Attach the bracket to

the handlebars and tighten the mounting screw.

NOTE: There are two molded plastic shims supplied with the Delphi computer brackets. The

THIN shim allows the bracket to fit Oversized 31.8 mm handlebars. The THICK shim

allows the bracket to fit standard 26.0mm handlebars.

CAUTION—When installing the system on a bicycle with front suspension, be sure to leave enough

slack for the action of the fork.

CYCLE COMPUTER

INSTALLING WIRED FRONT WHEEL SPEED SENSOR AND BRACKET

Blackburn_2/3_Manual 8/3/05 10:00 AM Page 12

INSTALLING THE COMPUTER ON YOUR BIKE INSTALLING THE COMPUTER ON YOUR BIKE

ENGLISH

INSTALLING WIRED REAR WHEEL SPEED AND CADENCE

SENSORS AND BRACKET (CONTINUED)

3. Adjust and position the sensor as closely as possible to the magnet and rotate the sensor

so the magnet passes within 1-3mm. Fully tighten the zip-ties once you have everything

properly aligned.

4. Depending on the length of your chainstays and where you want to position the sensor,

wrap the speed sensor wire once or twice around the chainstay and attach the speed

sensor using the zip-ties provided.

5. Attach the spoke magnet to a spoke on the same side of the wheel as the sensor. Tighten

the attachment screw just enough to hold the magnet in place but loose enough so that it

is still movable.

6. Adjust the position of the sensor and magnet so they are in proper alignment as shown in

the drawing tighten the zip-ties and magnet.

CYCLE COMPUTER

INSTALLING WIRED REAR WHEEL SPEED AND CADENCE

SENSORS AND BRACKET

On the Delphi 3.0, both speed and cadence are picked up from the rear wheel using a special

bracket, which has two sensors at the end of a long wire. One sensor picks up speed and

distance information from the rear wheel and the other picks up cadence information from the

crank. The cadence sensor is marked with a C.

1. Attach the cadence sensor to the LEFT chain stay near where the crank/pedal pass the

stay using the zip-ties provided. Snug up the zip-ties but do not fully tighten them. It is

recommended the cadence and rear wheel sensors be mounted on the top of the stay.

NOTE: The wires exiting the sensors should be pointing toward the front of the bike.

2. Attach the cadence magnet to the back side of the LEFT crank arm using the zip-tie

provided. The cadence magnet should be attached as closely to the pedal spindle as

possible.

Blackburn_2/3_Manual 8/3/05 10:00 AM Page 14

INSTALLING THE COMPUTER ON YOUR BIKE INSTALLING THE COMPUTER ON YOUR BIKE

ENGLISH

INSTALLING WIRED REAR WHEEL SPEED AND CADENCE

SENSORS AND BRACKET (CONTINUED)

7. Route the sensor wire forward and under the bottom bracket and along the bottom of the

down tube securing it occasionally with tape. Once you are near the head tube the sensor

wire should be wrapped around the front or rear derailleur cable housing and the around

the front brake cable housing.

CAUTION—Make sure you leave enough slack in the sensor wire so the handle bars can turn fully

from side to side without creating any stress.

8. Attach the bracket to the handlebars and tighten the mounting screw.

ATTACHING THE COMPUTER HEAD TO THE

HANDLEBAR BRACKET AND TESTING

When the bracket and sensors are completely installed on the bike, slide the

Delphi computer unit into the handlebar bracket. The computer should LOCK

into the bracket with an AUDIBLE "CLICK". If you do not hear a click or if

the Delphi computer body is not flush with the back edge of the bracket the

computer is not locked in place and may come out.

Once everything is assembled spin the wheel and turn the crank and make

sure speed and cadence are being displayed on the screen. If you are not

receiving one or both pieces of information, check the magnet and sensor

alignment and make sure the magnets are passing the proper point on the

sensor and that they are within 1-3mm. If they are closer to 3mm than to

1mm try reducing the gap and test the system again.

CYCLE COMPUTER

Blackburn_2/3_Manual 8/3/05 10:00 AM Page 16

KEYS AND THEIR FUNCTIONS KEYS AND THEIR FUNCTIONS

ENGLISH

QUICK PRESS VS. PRESS & HOLD

There are two key actions used to program and operate the Delphi computer.

QUICK PRESS—The key is pressed quickly and then immediately released. This is the most

common key action and is used for most operations. Throughout this manual, QUICK PRESS will

be indicated in BLUE.

PRESS & HOLD—The key is pressed and held for a period of 2-seconds until the desired action

takes place. This key action is generally used to enter a programming sequence or to clear

information from the display. Throughout this manual, PRESS & HOLD will be indicated in RED.

UPPER DISPLAY/EL KEY

Primary Function

•PRESS & HOLD to Change the Upper Display Window view.

OPTION KEY

Primary Function

•QUICK PRESS to change between OPTIONS within MODES.

Secondary Functions

•QUICK PRESS to Change a Variable in a Setting Sequence

Upward. HOLD for FAST ADVANCE

CYCLE COMPUTER

Blackburn_2/3_Manual 8/3/05 10:00 AM Page 18

SECTIONS OF LCD DISPLAY

ENGLISH

CYCLE COMPUTER

KEYS AND THEIR FUNCTIONS

ENGLISH

SPEED WINDOW

Current Speed is always

visible in the upper left

corner of the LCD display.

KM/H AND M/H

These icons indicate if the

unit is programmed to

display speed and distance

in Miles or Kilometers.

START/STOP KEY

Primary Function

•QUICK PRESS to Start/Stop TT Chronograph.

•PRESS & HOLD to Clear ALL Ride Data.

Secondary Functions

•QUICK PRESS to Change a Variable in a Setting Sequence

Downward. HOLD for FAST ADVANCE

•PRESS & HOLD to Clear Maximum Speed or Maximum

Cadence when in those Screens.

MODE KEY

Primary Function

•QUICK PRESS to change between MODES.

Secondary Functions

•PRESS & HOLD to Enter Setting Sequences.

•QUICK PRESS to Select a Variable in a Setting Sequence.

Blackburn_2/3_Manual 8/3/05 10:00 AM Page 20

Tabla de contenidos

Otros manuales de Accesorios para bicicletas de blackburn

blackburn

blackburn Delphi 5.0 Manual de usuario

blackburn

blackburn OUTPOST BIKE & CAMP 7108800 Manual de usuario

blackburn

blackburn DESIGN Series Manual de usuario

blackburn

blackburn Neuro Manual de usuario

blackburn

blackburn Grid Handlebar Bag Manual de usuario

blackburn

blackburn OUTPOST FAT BIKE Manual de usuario

blackburn

blackburn DAYBLAZER 550 FRONT Manual de usuario

blackburn

blackburn ATOM SL3.0 Manual de usuario

blackburn

blackburn Atom SL Manual de usuario

blackburn

blackburn Mammoth 2stage Manual de usuario

blackburn

blackburn Splashboard Rear Fender Manual de usuario

blackburn

blackburn Outpost Elite Cargo Bag Manual de usuario

blackburn

blackburn ATOM SL3.0 Manual de usuario

blackburn

blackburn GRID 2'fer Manual de usuario

blackburn

blackburn Design Series Manual de usuario

blackburn

blackburn CENTRAL 650 FRONT Manual de usuario

blackburn

blackburn 7074411 Manual de usuario

Manuales populares de Accesorios para bicicletas de otras marcas

Sigma

Sigma BC 16.16 Manual de usuario

Playcore

Playcore Dero Setbacks Manual de usuario

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manual de usuario

Cateye

Cateye RAPID X2 Manual de usuario

buratti meccanica

buratti meccanica Clorofilla Trail Manual de usuario

Shimano

Shimano SG-8R20 Instrucciones de funcionamiento

BOB

BOB YAK Manual de usuario

APLIC

APLIC 303303/20190717TW012 Manual de usuario

SRAM

SRAM AXS BlipBox Manual de usuario

Garmin

Garmin EDGE 500 Manual de usuario

Shimano

Shimano FD-RX810 Manual de usuario

Cateye

Cateye V2C - Manual de instrucciones

KMART

KMART 43115907 Manual de usuario

SIGMA SPORT

SIGMA SPORT Buster 2000 Manual de usuario

NVO Components

NVO Components STEM Manual de usuario

DAXYS

DAXYS BP188 Manual de usuario

XLC

XLC BV-W17 Manual de usuario

Deda Elementi

Deda Elementi SUPERBOX Manual de usuario

blackburn Delphi Manual de usuario

Manuales populares de Accesorios para bicicletas de otras marcas