Black Horse Model Excel 2000 Manual del propietario

SPECIFICATION



Wingspan : 1,530 mm 60.24 in.



Length : 1,340 mm 52.76 in.



Weight : 2.5 kg 5.5 Lbs.



Radio : 04 channels.



Servo : 04 servos.



Engine : 40-46 2 stroke

52 4 stroke

Instruction Manual book

MadeinVietnam.

EXCEL 2000.

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your EXCEL 2000. Use the parts listing below to

identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesignedtohelpthenew pilotonhiswaytosuccessfulR/C flight.Theywillalso beable

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modellingknife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

Some more parts.

HARDWAREPACK

COWLING.

Landinggear.....

Toavoid scratching yournew airplane,donot

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the

aircraftand toprotect thetable. Keepa couple

of jars or bowls handy to hold the small parts

after you open the bag.

Pleasetrialfitalltheparts. Makesureyouhave

the correct parts and that they fit and are

alignedproperly beforegluing!Thiswillassure

proper assembly.EXCEL 2000 ARF is hand

made from natural materials, every plane is

unique and minor adjustments may have to

be made. However, you should find the fit

superior and assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

of many harsh chemicals including the

following: paint thinner, C/A glue accelerator,

C/A glue debonder and acetone. Do not let

these chemicals come in contact with the

colors on the covering and the plastic parts.

PARTS LISTING.

FUSELAGE ASSEMBLY

(1) Fuselage.

WING ASSEMBLY

(1) Right wing half with pre-installed

aileron.

(1) Left wing half with pre-installed

aileron.

Some more parts .....

Tail section assembly

(1) Vertical stabilizer with pre-

installedrudder.

(1) Horizontal stabilizer with pre-

installedelevator halves.

SUGGESTION.

NOTE.

Instruction Manual.

+ This is not a toy

+ Be sure that no other flyers are using your

radio frequency.

+ Wear safety glasses.

+ Keep loose clothing and wires away from

thepropeller.

+ Do not start the engine if people are near.

Do not stand in line with the side of the

propeller.

+ Make engine adjustments from behind the

propeller only. Do not reach around the

spinningpropeller.

SAFETY PRECAUTION.

 1) Install the rubber grommets and brass

eyelets onto the aileron servo.

Because the size of servos differ, you

mayneed toadjustthe sizeofthe precutopen-

inginthe mount. Thenotch inthesides ofthe

mount allow the servo lead to pass through.

SERVO INSTALLATION.

Servomount.

EXCEL 2000.

5) Using Kwik Bond 5 Minute Epoxy, glue

the servo mount into place. Remove any ex-

cess epoxy using a paper towel and rubbing

alcohol. Use pieces of masking tape to hold

the tray in place until the epoxy fully cures.

2) Place the mount onto the wing haft,

aligning the cutout in the mount with the cut-

out in the wing. The two notches in the mount

should face the leading edge of the wing.

 3) While holding the servo mount firmly in

place, trace around it using a pen.

4) Remove the mount, and using a model-

ing knife, carefully remove the covering from

inside the outline you drew.

Pen.

Remove

covering.

Epoxyglue.

C/Aglue.

6)Using amodelingknife, carefullyremove

the covering from servo mount.

Remove covering.

 7) Install the aileron servo into the servo

mount, withthe outputshaft towardsthe lead-

ing edge of the wing, using the wood screws

provided with your radio system. Drill 1/16”

pilotholesthrough themount beforeinstalling

the screws. This will prevent the wood from

splitting.

Aileronservo.

Instruction Manual.

 2) Testfit thedihedral braceinto eachwing

half. The brace should slide in easily. If not,

use 220 grit sandpaper with a sanding block

and sand down the edges and ends of the

brace until it fits properly.

WINGASSEMBLY.

 1) Location the aluminium wing dihedral

brace.

Epoxyglue.

Bottom side.

Aluminium.

 3) Apply masking tape at the wing join to

hold the wing halves together securely.

INSTALLING THE AILERON LINKAGE.

1) Thread one nylon adjustable control

hornonto eachaileron torquerod. Thread the

horns on until they are flush with the ends of

the torque rods.

2) Thread one nylon clevis at least 5/16”

onto each of the two 2mm x 100mm threaded

wires.

3) Withthe aileronservo centered,install

theservo armonto theservo. The armshould

beinstalledso itisparallelwith thetrailingedge

of the wing.

Maskingtape.

EXCEL 2000.

4) Slide the pushrod wires following pic-

tureabove.

Cut.

INSTALLING THE ENGINE MOUNT.

INSTALLING THE STOPPER ASSEMBLY

1) The stopper has been pre-assembled

at the factory.

2) Using a modeling knife, cut one length

ofsilicon fuelline(thelengthofsiliconfuel line

iscalculatedbyhowtheweightedclunkshould

restabout 8mmaway fromtherearofthetank

andmove freelyinside thetank). Connectone

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the

stopper.

3) Carefully bend the second nylon tube

up at a 45 degree angle (using a cigarette

lighter). This tube will be the vent tube to the

muffler.

4)Carefully bendthe thirdnylon tubedown

ata 45degreeangle (usingacigarettelighter).

This tubewill bevent tubeto thefuelingvalve.

FUEL TANK.

When the stopper assembly is installed

in the tank, the top of the vent tube should

rest just below the top surface of the tank.

It should not touch the top of the tank.

Instruction Manual.

Blow through one of the lines to ensure

the fuel lines have not become kinked inside

the fuel tank compartment. Air should flow

througheasily.

9) To secure the fuel tank in place, apply a

bead of silicon sealer to the forward area of

thetank, whereit exitsthefuselage behindthe

enginemountingbox andtotherearofthetank

at the forward bulkhead.

Do not secure the tank into place

permanently until after balancing the

airplane. You may need to remove the tank

to mount the battery in the fuel tank

compartment.

8) Feed three lines through the fuel tank

compartment and through the pre-drilled hole

in the firewall. Pull the lines out from behind

the engine, while guiding the fuel tank into

place. Push the fuel tank as far forward as

possible,the frontofthetankshould justabout

touch the back of the firewall.

6) When satisfied with the alignment of

thestopperassemblytightenthe3mmx20mm

machine screw until the rubber stopper

expands and seals the tank opening. Do not

over tighten the assembly as this could cause

the tank to split.

7) Using a modeling knife, cut 3 lengths of

fuel line 150mm long. Connect 2 lines to the 2

vent tubes and 1 line to the fuel pickup tube in

the stopper.

Fueltank.

5) Test fit the stopper assembly into the

tank. It may be necessary to remove some of

the flashing around the tank opening using

amodeling knife. Ifflashing is present, make

sure none of it falls into the tank.

Locate the long piece of wire used for the

throttlepushrod. Oneendofthewire hasbeen

pre-bend in to a “Z” bend at the factory. This

“Z” bend should be inserted into the throttle

armofthe enginewhentheengine isfittedonto

theengine mount.Fittheengineto theengine

mount using the screws provided.

INSTALLING THE ENGINE.

Markpoint.

EXCEL 2000.

NOSE GEAR INSTALLATION.

Adjust the nose gear steering arm until the

arm is parallel with the fire wall.

Installing steering arm as follow

Steering arm.

Instruction Manual.

Steering arm.

INSTALLING THE SPINNER.

Installthe spinnerbackplate,propellerand

spinner cone. The spinner cone is held in

place using two 3mm x 12mm wood screws.



1) Using a modeling knife, remove the

coveringfromover thetwomaingearmounting

slots located in the bottom of the fuselage.



2) Using the two landing gear straps as a

guide,mark thelocations ofthe four mounting

screws onto the fuselage surface.



3) The landing gear wire is held in place

using two nylon landing gear straps and four

wood screws.

MAIN GEAR INSTALLATION.

EXCEL 2000.

HORIZONTAL STABILIZER.



1) Using a ruler and a pen, locate the

centerline of the horizontal stabilizer, at the

trailingedge, andplaceamark.Use atraingle

and extend this mark, from back to front,

across the top of the stabilizer. Also extend

thismarkdown theback ofthe trailingedge of

the stabilizer.

Center line.



3) Slide the stabilizer into place the

fuselage. Use a pen and draw lines onto the

stabilizerwhereitandthefuselage sidesmeet.

Remove covering.



2) Usinga modelingknife,carefullyremove

the covering from over the vertical stabilizer

mounting slot in the top of the fuselage.

The top of the stabilizer does not have

the hinge pins exposed.

Pen.



4) Remove the stabilizer. Using the lines

youjustdrew asa guide,carefully removethe

covering from between them using a model-

ingknife.

ELEVATOR SERVO INSTALLATION.

See pictures below:

Elevator servo.

Otros manuales para Excel 2000

Tabla de contenidos

Otros manuales de Juguete de Black Horse Model

Black Horse Model

Black Horse Model Mustang P51 Manual del propietario

Black Horse Model

Black Horse Model HEINKEL HE 111 Manual de usuario

Black Horse Model

Black Horse Model MKII Manual del propietario

Black Horse Model

Black Horse Model Sea Fury BH102 Manual de usuario

Black Horse Model

Black Horse Model Silence Twister Manual del propietario

Black Horse Model

Black Horse Model L-39 Albatros Manual del propietario

Black Horse Model

Black Horse Model FAIRCHILD 24W Manual del propietario

Black Horse Model

Black Horse Model Sea Fury Manual de usuario

Black Horse Model

Black Horse Model Fieseler Fi156C STORCH Manual de usuario

Black Horse Model

Black Horse Model Impulse 100TD Manual de usuario

Black Horse Model

Black Horse Model MIG-29 Manual del propietario

Black Horse Model

Black Horse Model EXTRA 300 Manual del propietario

Black Horse Model

Black Horse Model Extra S Manual del propietario

Black Horse Model

Black Horse Model Extra 300S Manual de usuario

Black Horse Model

Black Horse Model Spitfire-EP BH 127 Manual del propietario

Black Horse Model

Black Horse Model MDM-1FOX Manual del propietario

Black Horse Model

Black Horse Model PITTS Manual del propietario

Black Horse Model

Black Horse Model Space Walker BH65 Manual del propietario

Black Horse Model

Black Horse Model TURBO BEAVER BH162 Manual del propietario

Black Horse Model

Black Horse Model Ryan Manual del propietario

Black Horse Model

Black Horse Model Excel 2000 Manual del propietario

Black Horse Model

Black Horse Model AT.6-Texan Manual del propietario

Black Horse Model

Black Horse Model SUPER DECATHLON Manual del propietario

Black Horse Model

Black Horse Model Corsair BH64 Manual del propietario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario