Black Horse Model Impulse 100TD Manual de usuario

SPECIFICATION

Instruction Manual book



Wingspan : 1,750 mm 68.90 in.



Length :



Weight : 4,4 kg 9.68 Lbs.



Radio : 07 channels.



Servo : 08 servos.

1,285mm 50.59in.



Engine : 55 - 2 Stroke

15 -20CC Gas.



ElectricMotor: RIMFIRE.80

Battery:5-6Cells-Li-Poly18.5-22.2V-5.500mAh.

Propeller: 15X 6

Speed control: 60A.

ITEMCODE:BH121.

Madein Vietnam.

Impulse 100TD - Item code: BH 121 . Instruction Manual

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manualthoroughlybefore startingassemblyof your Impulse 100TD.Usethe partslistingbelow to

identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesigned to helpthenewpilotonhiswaytosuccessful R/C flight. Theywillalsobeable

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modellingknife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

Some more parts.

HARDWAREPACK

COWLING.

Landing gear.....

Toavoidscratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the air-

craftand to protectthe table. Keepa couple of

jars or bowls handy to hold the small parts af-

ter you open the bag.

Pleasetrial fit all theparts.Makesureyouhave

the correct parts and that they fit and are

alignedproperlybeforegluing!Thiswill assure

properassembly.Impulse 100TDARFis hand

made from natural materials, every plane is

unique and minor adjustments may have to

be made. However, you should find the fit su-

perior and assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

of many harsh chemicals including the follow-

ing:paintthinner,C/Aglueaccelerator,C/Aglue

debonderand acetone.Donotletthesechemi-

cals come in contact with the colors on the

covering and the plastic parts.

PARTS LISTING.

FUSELAGE ASSEMBLY

(1) Fuselage.

WING ASSEMBLY

(1) Right wing half with pre-installed

aileron.

(1) Left wing half with pre-installed

aileron.

Tail section assembly

(1) Vertical stabilizer with pre-

installedrudder.

(1) Horizontal stabilizer with pre-

installedelevatorhalves.

SUGGESTION.

NOTE.

Impulse 100TD - Item code: BH 121 . Instruction Manual

Caution: this model is not a toy!

If you are a beginner to this type of powered

model,pleaseaskan experienced model flyer

forhelp and support.If you attemptto operate

themodelwithoutknowingwhatyouaredoing

you could easily injure yourself or somebody

else. Please keep your safety and well-being

in mind at all times.

Important: before you start construction

Evenif you have already built a large number

ofRC models pleaseread right through these

instructions and check all the kit components

against the parts list. We have taken great

trouble to keep construction as simple as

possible, without making any compromises

in the area of safety.

Note regarding the film covering

Minor creases or bubbles may develop in the

film covering due to major fluctuations in

weather conditions (temperature, humidity

etc.); in rare cases you may even find a slight

warp in a component. These minor faults are

in the nature of film-covered built-up wooden

structures, and can easily be corrected using

a heat gun, as commonly used for modelling.

Creases: Blowwarmairoverthearea

and rub down with a soft

cloth.

When self-tapping screws have to be

screwed into wood, apply a little white

glue to prevent them shaking loose: just

squirt white glue into the hole and fit the

screw.

+ This is not a toy

+ Be sure that no other flyers are using your

radio frequency.

+ Do not smoke near fuel

+ Store fuel in a cool, dry place, away from

children and pets.

+ Wear safety glasses.

+The glow plug clip must be securely at-

tached to the glow plug.

+ Do not flip the propeller with your fingers.

+ Keep loose clothing and wires away from

thepropeller.

+ Do not start the engine if people are near.

Do not stand in line with the side of the pro-

peller.

+ Make engine adjustments from behind the

propeller only. Do not reach around the spin-

ningpropeller.

SAFETY PRECAUTION.

Wing warp: Hold the panel twisted

gently in the opposite

direction to the warp, and

apply warm air to remove

the creases from the

covering.

Caution! do not heat the film more than is

absolutely necessary. If the air or the iron is

too hot, the film may melt and holes may be

formed.

This model is highly pre-fabricated and can

bebuilt in a very short time. However,thework

which you have to carry out is important and

must be done carefully. The model will only

be strong and fly well if you complete your

tasks competently - so please work slowly

and accurately.

REPLACEMENT LARGE PARTS

B1.

D2. G.

B2.

D1.

A.Cowling.

B. Wing panel(B1,B2).

C. Fuselage.

D. Horizontal stabilizer.

E.Rudder.

F. Aluminium wing dihedral brace.

G. Decal sheet .

Impulse 100TD - Item code: BH 121 . Instruction Manual

REPLACEMENT SMALL PARTS

 1. Install the rubber grommets and brass

eyelets onto the aileron servo.

7. Wheels.

2. Wheel pants.

3. Fuel Tank.

5. Tail gear set.

8.Spinner.

9. Plastic parts for elevator and rudder pushrod.

1. Aluminium landing gear.(Right & Left).

6. Plastic parts for landing gear.

4. Engine mount ply of wood .

1.INSTALLING THE AILERON SERVO.

I. SERVO

Temporary pin to

keep hinge centered.

Cutthe covering

awayfromtheslot.

Bottom side

Aileron

Impulse 100TD - Item code: BH 121 . Instruction Manual

2.Using a modelingknife,remove the cov-

ering servo tray.

Assemble then apply drops of thin

C/A to center of hinge,on both sides.

Servo tray.

Removecovering

3. Drill 1,5mm pilot holes through the block

of wood for each of the four mounting screws

provided with the servo. Install servo into ai-

leron servo tray as same as picture below.

4. Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

Secure.

Thread.

Electric

wire.

Impulse 100TD - Item code: BH 121 . Instruction Manual

Repeat the procedure for the other wing

half.

5. Instal servo tray with aileron servo into

the wing as same as picture below.

2x10mm.

2. INSTALLING THE AILERON CONTROLHORN.

Secure.

Aileroncontrol horn

Installaileroncontrol hornassame

aspicturebelow.

Repeat the procedure for the other wing

half.

Installing the aileron linkages as pictures

below.

Attach the clevis to the outer hole in the con-

trol horn.

A+B Epoxy

PLUS

Control horn

of the aileron

60mm

M2.

3.INSTALLING THE AILERON

LINKAGES .

Impulse 100TD - Item code: BH 121 . Instruction Manual

Electric

wire

2x10mm.

Secure.

Control horn of the flap

A+B Epoxy

PLUS

2. INSTALLING THE FLAPCONTROLHORN.

II. FLAP

1. INSTALLING THE FLAP SERVO .

Thread

Impulse 100TD - Item code: BH 121 . Instruction Manual

Repeat the procedure for the other wing

half.

THERE ARE TWO OPTIONS:

1. ELECTRIC MOTOR

2. ENGINE MOUNT.

1. OPTION 1: ELECTRIC MOTOR

INSTALLING ELECTRIC MOTOR.

Installing the aileron linkages as pictures

below.

3.INSTALLING THE FLAP

LINKAGES.

60 mm

M2.

Control horn

of the flap

3x 15mm

Bottom side

Flap Aileron

Impulse 100TD - Item code: BH 121 . Instruction Manual

Remove

Wood.

3x 15mm

Secure.

Drill a hole 2mm diameter.

C/Aglue.

Impulse 100TD - Item code: BH 121 . Instruction Manual

See pictures below:

2. OPTION 2: ENGINE MOUNT

5x 80mm

Secure. Right side

Frontview.

Rotor sharft.

Motor.

Left side.

Battery.

3 x 15mm

Frontview.

INSTALLING THE ENGINE MOUNT.

Otros manuales para Impulse 100TD

Tabla de contenidos

Otros manuales de Juguete de Black Horse Model

Black Horse Model

Black Horse Model HAWKER TYPHOON MK1B Manual del propietario

Black Horse Model

Black Horse Model Cobra Manual del propietario

Black Horse Model

Black Horse Model SU-26M Manual del propietario

Black Horse Model

Black Horse Model VIPER JET TURBINE Manual del propietario

Black Horse Model

Black Horse Model JU87-STUKA Manual del propietario

Black Horse Model

Black Horse Model BH129 Manual de usuario

Black Horse Model

Black Horse Model SUPER DECATHLON Manual del propietario

Black Horse Model

Black Horse Model GLASAIR Manual del propietario

Black Horse Model

Black Horse Model BH180 Manual del propietario

Black Horse Model

Black Horse Model Thermal 3.0 Manual de usuario

Black Horse Model

Black Horse Model CHIPMUNK Manual del propietario

Black Horse Model

Black Horse Model Spitfire 40 Manual de usuario

Black Horse Model

Black Horse Model Mustang P51 Manual de usuario

Black Horse Model

Black Horse Model Motion RC PIPER J-3 CUB Manual del propietario

Black Horse Model

Black Horse Model dornier DO335 Manual de usuario

Black Horse Model

Black Horse Model SPEED AIR BH.08 Manual del propietario

Black Horse Model

Black Horse Model Travel Air BH06-A Manual del propietario

Black Horse Model

Black Horse Model BH160 Manual del propietario

Black Horse Model

Black Horse Model T-28 Trojan 120 Manual de usuario

Black Horse Model

Black Horse Model Edge 540-V3 Manual del propietario

Black Horse Model

Black Horse Model BEDE BD-5J Manual del propietario

Black Horse Model

Black Horse Model GILMORE BH179 Manual del propietario

Black Horse Model

Black Horse Model TURBO BEAVER BH162 Manual del propietario

Black Horse Model

Black Horse Model Focke-Wulf FM 190A Manual del propietario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario