Black Box AC1037A Manual de usuario

DVI Video with Stereo Audio

Fiber Optic Transmission System

JULY 2007

AC1037A

AC1037A-XMIT

AC1037A-REC

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

AC1037A | AC1037A-XMIT | AC1037A-REC

TRADEMARKS USED IN THIS MANUAL

UL is a registered trademark of Underwriters Laboratories Incorporated.

Any other trademarks used in this manual are acknowledged to be the property of the

trademark owners.

FEDERAL COMMUNICATIONS COMMISSION AND

CANADIAN DEPARTMENT OF COMMUNICATIONS

RADIO FREQUENCY INTERFERENCE STATEMENTS

TRADEMARKS

FCC STATEMENT

This equipment generates, uses, and can radiate radio frequency energy and if not installed

and used properly, that is, in strict accordance with the manufacturer’s instructions, may

cause interference to radio communication. It has been tested and found to comply with

the limits for a Class A computing device in accordance with the specications in Subpart

B of Part 15 of FCC rules, which are designed to provide reasonable protection against

such interference when the equipment is operated in a commercial environment. Operation

of this equipment in a residential area is likely to cause interference, in which case the user

at his own expense will be required to take whatever measures may be necessary to correct

the interference.

Changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emission from

digital apparatus set out in the Radio Interference Regulation of the Canadian Department

of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique publié par le ministère des Communications du Canada.

AC1037A | AC1037A-XMIT | AC1037A-REC

NOM STATEMENT

Normas Ociales Mexicanas (NOM)

Electrical Safety Statement

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el

aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia

futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación

deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la

tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean

recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea

recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo

descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a

personal de servicio calicado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no interera su

uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra o supercie

similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes que

impidan el ujo de aire por los oricios de ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como

radiadores, registros de calor, estufas u otros aparatos (incluyendo amplicadores)

que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo

descrito en el instructivo de operación, o como se indique en el aparato.

AC1037A | AC1037A-XMIT | AC1037A-REC

12. Precaución debe ser tomada de tal manera que la tierra sica y la polarización del

equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean

pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo

particular atención a los contactos y receptáculos donde salen del aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones

del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de

energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por

un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados

sobre la cubierta u oricios de ventilación.

18. Servicio por personal calicado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en

su desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

Standards to which conformity is declared: EN 55103-1:1997 EN 55103-2:1997

CE INFORMATION

NOM STATEMENT (Continued)

AC1037A | AC1037A-XMIT | AC1037A-REC

ITEMS INCLUDED

Depending on which product you ordered, you should have received:

AC1037A-XMIT:

Qty Description

1 AC1037A-XMIT Transmitter

1 Power Supply

1 AC line cord

1 User Manual

AC1037A-REC:

Qty Description

1 AC1037A-REC Receiver

1 Power Supply

1 AC line cord

1 User Manual

AC1037A | AC1037A-XMIT | AC1037A-REC

GENERAL INFORMATION

The AC1037A is a transmitter/receiver pair that transmits a single channel of DVI video (up

to WUXGA) and two audio channels over one single mode ber.

The system’s all digital encoding delivers noise-free transmissions that retain all of their

initial parameters, regardless of ber optic cable attenuation. System operation may be easily

monitored using integral indicator LEDs on each unit that continuously signify the presence

of baseband video and audio signals.

TECHNICAL SPECIFICATIONS

Video:

Number of Video Channels .....................................1 single-link DVI up to 1920x1200

Video Processing .....................................................24 bits, no compression or scaling

DVI Input Loop-through .........................................Yes

EDID (DDC) Support..............................................Yes, from loop-through or internal

Pixel Clock Range ...................................................25 - 165 Mhz, continuous

Scanning System Supported....................................Progressive or Interlaced

Format Supported ....................................................RGB or YPrPb

Audio:

Number of Audio Channels.....................................2, unbalanced

Frequency Response ................................................+0/-0.5 dB, 20 Hz to 20 kHz

Bits-per-Sample/Sampling Rate ..............................24 bits; >48kHz

Maximum Audio Level ...........................................+10 dBu

SNR (A-Weighted)...................................................100 dB

THD+N ....................................................................0.001%, 20 Hz - 20 kHz

Channel Phase Differential......................................+0.1o

Crosstalk ..................................................................100 dB (1 kHz)

Input Impedance ......................................................>24 k Ohms

Output Impedance ...................................................< 1 Ohm

Audio to Video Diff. Delay (skew)..........................300 uSec

AC1037A | AC1037A-XMIT | AC1037A-REC

TECHNICAL SPECIFICATIONS (Continued)

Optical:

Operating Wavelength.............................................CWDM (1300 - 1600 nm band )

Optical Fibers...........................................................8-10/125 microns SM

Optical Connector....................................................ST

Class I Laser Product complies with FDA performance standard for laser products,

Title 21, Code of Federal Regulations, Sub-Chapter J.

Miscellaneous:

Operating Temp. Range...........................................-20oC to +50oC

Operating Power ......................................................9-24 Volts AC or DC@10 watts (max.)

Loss Budget and Maximum Transmission Distance:

Loss Budget (in dB) Distance* (in km)...................0-15 dB, 15 km

*Distance specications are only approximate and are not guaranteed.

Operating loss budget must not be exceeded.

DANGER! The transmitting element in the AC1037A-XMIT unit contains a solid state Laser

Diode located within the optical connector. This device emits invisible infrared electromag-

netic radiation which can be harmful to human eyes. The radiation from this optical connector, if

viewed at close range without a fiber optic cable connected to the optical connector, may be of

sufficient intensity to cause instantaneous damage to the retina of the eye. Direct viewing of this

radiation should be avoided at all times.

AC1037A | AC1037A-XMIT | AC1037A-REC

The AC1037A transmission system is ready for immediate use. There are indicator LEDs

on the units for monitoring purposes. The following instructions describe the typical

installation procedure and the function of the LED indicators ( See Page 13 ).

1. Power off the PC and AC1037A Units.

2. Connect the DVI video source (PC) to the video

input DVI-D connector on the transmitter unit.

3. Connect a monitor to the loop-thru input of

transmitter unit if that is the monitor type

to be used on the receiver end of the link.

Ensure that the Loop/Internal EDID Switch

is in the “Loop” position.

If the loop-thru default settings are desired, ensure that the Loop/Internal EDID

Switch is in the “Internal” position. No monitor connection to the transmitter box is

required for this loop-thru position.

4. Connect the video output(s) on the receiver unit to the DVI-D connector(s).

5. Connect the ber optic cable between the two AC1037A units.

6. Connect the audio input signals to the transmitter stereo jack and the audio output to

the receiver stereo jack.

7. Apply power to both the AC1037A units and the PC or video source. Refer to Figure 1.

8. When power is applied, the green POWER LED will light, indicating the presence of

operating power. The VIDEO LED will give an indication as described on page 13.

9. The green AUDIO LED will give an indication as stated on page 13.

10. The system should now be operational.

INSTALLATION

AC1037A | AC1037A-XMIT | AC1037A-REC

SYSTEM CONNECTIONS

The input and output connections for the AC1037A system is as follows:

Audio Connector (Transmitter & Receiver): 3.5mm stereo jack

Video Connector (Transmitter & Receiver): DVI-D connector

Video Pin Out: Transmitter Receiver

1 Red (-) Red (-)

2 Red (+) Red (+)

3 Red Shield Red Shield

4 N/C N/C

5 N/C N/C

6 DDC CLK DDC CLK

7 DDC Data DDC Data

8 N/C N/C

9 Green (-) Green(-)

10 Green (+) Greeen(+)

11 Green Shield Green Shield

12 N/C N/C

13 N/C N/C

14 +5V Power +5V Power

15 GND (for +5V) GND (for +5V)

16 Hot Plug Detect Hot Plug Detect

17 Blue (-) Blue (-)

18 Blue (+) Blue (+)

19 Blue Shield Blue Shield

20 N/C N/C

21 N/C N/C

22 Pixel Click Shield Pixel Click Shield

23 Pixel Click (+) Pixel Click (+)

24 Pixel Click (-) Pixel Click (-)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de Black Box

Black Box

Black Box AC1003A-R2 Manual de usuario

Black Box

Black Box ME806A Manual de usuario

Black Box

Black Box VX-1002-TX Manual de usuario

Black Box

Black Box AC560A Manual de usuario

Black Box

Black Box IC564A Manual de usuario

Black Box

Black Box Quad Audio Balun Manual de usuario

Black Box

Black Box InvisaPC DTX1000-T Manual de usuario

Black Box

Black Box AC504A-WP Manual de usuario

Black Box

Black Box IC565A Manual de usuario

Black Box

Black Box HD View AC3000A-R2 Series Manual de usuario

Black Box

Black Box ACR500HDMI-T Manual de usuario

Black Box

Black Box IC447A Manual de usuario

Black Box

Black Box CATX Series Manual de usuario

Black Box

Black Box Agility Zero-U ACR500DP-T Manual de usuario

Black Box

Black Box HD View AC3000A-R2 Series Manual de usuario

Black Box

Black Box FiberPath AC444A Manual de usuario

Black Box

Black Box AC603A Manual de usuario

Black Box

Black Box AC1004A-R3 Manual de usuario

Black Box

Black Box Agility Zero-U ACR500DP-T Manual de usuario

Black Box

Black Box AC3000A Manual de usuario

Black Box

Black Box IC449A Manual de usuario

Black Box

Black Box AC1003A-R2 Manual de usuario

Black Box

Black Box Agility Zero-U ACR500DP-T Manual de usuario

Black Box

Black Box InvisaPC Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario