Black Box SW546A Manual de usuario

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

OCTOBER 1996

SW545A

SW546A

Port Manager Switches

Port Manager Switch

ON RDY

ACTIVITY

12345678

Port Manager Switch

ON RDY

ACTIVITY

12345678

ACTIVITY

12345678

FCC AND IC STATEMENTS, TRADEMARKS

FEDERAL COMMUNICATIONS COMMISSION

AND

INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio frequency

energy and if not installed and used properly, that is, in strict

accordance with the manufacturer’s instructions, may cause

interference to radio communication. It has been tested and found

to comply with the limits for a Class A computing device in

accordance with the specifications in Subpart J of Part 15 of FCC

rules, which are designed to provide reasonable protection against

such interference when the equipment is operated in a commercial

environment. Operation of this equipment in a residential area is

likely to cause interference, in which case the user at his own

expense will be required to take whatever measures may be

necessary to correct the interference.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise

emission from digital apparatus set out in the Radio Interference

Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numériques de

classe A prescrites dans le Règlement sur le brouillage radioélectrique

publié par Industrie Canada.

TRADEMARKS USED IN THIS MANUAL

AT and IBM are registered trademarks, and PC/XT is a trademark,

of IBM Corporation.

ProComm is a registered trademark of Symantec Corporation.

PORT MANAGER SWITCHES

NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes

de que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para

referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de

operación deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,

cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,

etc.

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales

que sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como

sea recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más

allá a lo descrito en las instrucciones de operación. Todo otro servicio

deberá ser referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no

interfiera su uso. La colocación del aparato eléctrico sobre una cama,

sofá, alfombra o superficie similar puede bloquea la ventilación, no se

debe colocar en libreros o gabinetes que impidan el flujo de aire por los

orificios de ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de

calor como radiadores, registros de calor, estufas u otros aparatos

(incluyendo amplificadores) que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo

del tipo descrito en el instructivo de operación, o como se indique en el

aparato.

NOM STATEMENT

12. Precaución debe ser tomada de tal manera que la tierra fisica y la

polarización del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no

sean pisados ni pellizcados por objetos colocados sobre o contra ellos,

poniendo particular atención a los contactos y receptáculos donde salen

del aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las

recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las

lineas de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo no

sea usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean

derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del

aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en

su desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

PORT MANAGER SWITCHES

Contents

Chapter Page

1. Specifications ............................................................................................. 7

2. Introduction ............................................................................................. 11

2.1 General Overview .............................................................................. 11

2.2 The Port Manager Switches Illustrated ........................................... 13

3. Getting Started ......................................................................................... 15

3.1 Setting Default Communication Parameters .................................. 15

3.2 Connecting Your PC to the PM Switch ............................................ 16

3.3 Applying Power to the PM Switch .................................................... 17

3.4 Communicating with the PM Switch Unit ....................................... 18

4. Installation ................................................................................................ 22

4.1 Setting the SETUP Switch ................................................................ 22

4.2 Connecting a Modem to the PM Switch .......................................... 25

4.3 Initializing the Unit to Default Settings .......................................... 26

4.4 Connecting Devices to the PM Switch ............................................. 26

5. Configuration ........................................................................................... 28

5.1 Accessing the PM Switch’s Command Mode .................................. 28

5.2 Defining and Reading the Site I.D. ................................................... 29

5.3 Port Configuration ............................................................................ 30

6. Operation ................................................................................................. 36

6.1 Connecting and Disconnecting Ports .............................................. 36

6.2 Defining Hunt Groups ..................................................................... 39

6.3 Port Buffers ....................................................................................... 41

TABLE OF CONTENTS

Chapter Page

7. Saving Configuration Parameters ............................................................ 42

7.1 Sending Parameters to a File ............................................................ 42

7.2 Restoring Saved Parameters ............................................................. 43

8. Command Reference Guide ................................................................... 44

8.1 Command Conventions .................................................................... 44

8.2 Command Response ......................................................................... 45

8.3 Command Summary ......................................................................... 46

8.4 Command Set .................................................................................... 47

9. Troubleshooting ...................................................................................... 56

9.1 Calling Black Box .............................................................................. 56

9.2 Shipping and Packaging ................................................................... 56

Appendix A: Pinouts .........................................................................................57

Appendix B: SW546A-D48 ................................................................................62

PORT MANAGER SWITCHES

Compliance — FCC Class A, IC Class/classe A

Interfaces — Proprietary modular serial, compatible with EIA

RS-232 (DTE)

Protocol — Asynchronous

Code Set — ASCII

Data Format — Either 8 data bits, no parity, or 7 data bits, even or

odd parity; either 1 or 2 stop bits (independently

user-selectable for each port)

Flow Control — DTR/CTS (hardware), X-ON/X-OFF (software), or

both (independently user-selectable for each port)

Operation —

Full duplex (command echo) or half-duplex (no echo),

user-selectable

Data Rate — 38,400, 19,200, 9600, 4800, 2400, 1200, or 300 bps

(independently user-selectable for each port)

Maximum

Distance — Up to 150 ft. (45.7 m); might be less if you use flat-

Internal Memory — 256 KB battery-backed, autoconfiguring, dynamically

allocated buffer SRAM on SIMMs (or DIPs in some

units); units with 512 KB are available as special

quotes

1. Specifications

CHAPTER 1: Specifications

User Controls — Keyboard commands;

(2) Front-mounted CLEAR and SET pushbuttons;

(3) Rear-mounted:

(1) 8-position DIP switch for comm. parameters;

(1) 115-/220-VAC slide switch;

(1) OFF/ON rocker switch

Indicators — All front-mounted:

Both models: ON and RDY (ready) LEDs;

SW545 models: (8) ACTIVITY LEDs;

SW546 models: (16) ACTIVITY LEDs

Connectors — All rear-mounted:

All models: (1) IEC 320 male power inlet;

SW545 models: (8) RJ-11 female;

SW546 models: (16) RJ-11 female

Leads/Signals

Supported — Ports 1 and 2:

Pins 1 through 6 (CTS in, SGND, RD in, RLSD

[DCD] in, TD out, and DTR out respectively);

Ports 3 and up:

Pins 1 through 6 (CTS in, SGND, RD in, RTS [held

high], TD out, and DTR out respectively)

Power — From outlet through 6-ft. (1.8-m) power cord

(included with SW545 units only) and internal

power supply:

Either 115 VAC, 60 Hz or 220 VAC, 50 Hz (user-

selectable);

Consumption: 5 watts

Fuse — 250 volts, 125 mA Slo-Blo

Temperature

Tolerance — 32 to 122˚ F (0 to 50˚ C)

PORT MANAGER SWITCHES

Humidity

Tolerance — 20 to 80% noncondensing

Size — 1.8" (1U) H x 17"W x 6.5"D (4.4 x 43.2 x 16.5 cm);

when rackmount brackets are added, the unit is

19" (48.3 cm) wide

Weight — 6 lb. (2.7 kg)

CHAPTER 2: Introduction

2.1 General Overview

With our 8-port and 16-port Port Manager (PM) Switches, you can control

and manage a network without having to worry about the in-band restrictions

associated with SNMP. Both models of the Switch make it possible to establish

on-site or remote communication with any piece of equipment that has an RS-

232 command port. You can access such devices without having to travel to

the installation site, even when your network is down.

Versatile Connectivity

The PM Switch provides a practical solution for applications that require

communicating with devices using dissimilar data rates. You can individually

tailor the Switch’s 8 or 16 ports for specific data rates, data formats, types of

flow control, and various other custom parameters and options.

Easy Setup and Operation

Configuring the PM Switch is simple. You can select communications

parameters or enable or disable options through a convenient menu system.

The Switch can be easily configured to fit the requirements of almost any

data-communications application.

Limited Command Access

The PM Switch is ideal for situations that require two tiers of command/

configuration security. You can individually configure the Switch’s ports

either as Administrator ports with access to all commands, or as User ports

with access to basic commands only.

Modular Design

The PM Switch’s RJ-11 jacks can be quickly and easily connected (through

RS-232 modular adapters) to computers, modems, and other LAN/WAN

hardware. The Switch is compact and occupies only one rack unit (1.75

inches) of vertical rack space.

Buffered Ports

The PM Switch has 256 KB of nonvolatile, dynamically allocated buffer

memory that prevents data from overflowing during communication sessions.

If your application requires more memory, call Black Box for technical

support; they might be able to provide you with a quote on units with 512-KB

buffers.

2. Introduction

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Black Box

Black Box

Black Box LGB1108A Manual de usuario

Black Box

Black Box IC562A Manual de usuario

Black Box

Black Box ServSwitch RMK19WX 1 Manual de usuario

Black Box

Black Box ServSwitch 4site Manual de usuario

Black Box

Black Box LE1401A Manual de usuario

Black Box

Black Box LBH21xA-H-SFP Manual de usuario

Black Box

Black Box LB8405A-R3 Manual de usuario

Black Box

Black Box ServSwitch SW627A-R2 Manual de usuario

Black Box

Black Box LH8050A Manual de usuario

Black Box

Black Box SW1020A Manual de usuario

Black Box

Black Box ServSwitch Octet KV1701 Manual de usuario

Black Box

Black Box SW595A Manual de usuario

Black Box

Black Box 40418 Manual de usuario

Black Box

Black Box LGB5128A Manual de usuario

Black Box

Black Box SW980A Manual de usuario

Black Box

Black Box ServSelect IP VM KV2116A Manual de usuario

Black Box

Black Box ServSwitch Wizard SW652A Manual de usuario

Black Box

Black Box LPH008A-R2 Manual de usuario

Black Box

Black Box LBH120A-H SERIES Manual de usuario

Black Box

Black Box Hub Manual de usuario

Black Box

Black Box LPB201A Manual de usuario

Black Box

Black Box COS-2 Manual de usuario

Black Box

Black Box LBH120A-H SERIES Manual de usuario

Black Box

Black Box SC120A-R2 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario