Black Box LWE120UK Manual de usuario
BLACK BOX®
Quick Installation Guide
Wireless Ethernet Extender
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax
724-746-0746 • Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence,
PA 15055-1018 • Web site: www.blackbox.com • E-mail: info@blackbox.com
Customer
Support
Information
March 2009
codes codes
codes codes
codes codes
LWE120A LWE120A-KIT
LWE120AE LWE120UK-KIT
LWE120UK
Page 2 724-746-5500 | blackbox.com
Chapter 1: Overview
About the Quick Installation Guide
This Quick Installation Guide is intended to guide professional installers to install
and configure the Wireless Ethernet Extender. It covers procedures to assist you in
avoiding unforeseen problems.
1. Overview
1.1 Introduction
The Wireless Ethernet Extender is a 2x2 outdoor access point. The LWE120A
operates at 2.4-GHz band. Ideally suited for SMB or hotspot networks, this
breakthrough innovation provides superior Wi-Fi network solutions at significantly
lower cost.
In addition, the easy-to-install Wireless Ethernet Extender is also a
high-performance last-mile broadband solution that provides reliable wireless
network coverage for outdoor broadband application.
Figure 1-1. Front view.
Page 3
724-746-5500 | blackbox.com
Chapter 1: Overview
Figure 1-2. Back view.
RJ-45 port
Grounding point
Reset button
Figure 1-3. Inside the bottom cover.
Page 4 724-746-5500 | blackbox.com
Chapter 2: Preparing for Installation
2. Preparing for Installation
This chapter describes safety precautions and product information you have to
know. Read this chapter before installing the Wireless Ethernet Extender.
Professional Installation Required
Seek assistance from a professional installer who is well trained in RF installation
and knowledgeable in the local regulations.
Safety Precautions
To keep you safe and install the hardware properly, read and follow these safety
precautions.
1. If you are installing the Wireless Ethernet Extender for the first time, for your
safety as well as others’, please assistance from a professional installer who has
received safety training on the hazards involved.
2. Keep safety as well as performance in mind when selecting your installation
site, especially where there are electric power and phone lines.
3. When installing the Wireless Ethernet Extender, note the following things:
• Do not use a metal ladder;
• Do not work on a wet or windy day;
• Wear shoes with rubber soles and heels, rubber gloves, and a long-sleeved shirt
or jacket.
4. When the system is operational, avoid standing directly in front of it. Strong RF
fields are present when the transmitter is on.
Installation Precautions
To keep the Wireless Ethernet Extender well while you are installing it, read and
follow these installation precautions.
1. Users MUST use a proper and well-installed grounding and surge arrestor with
the Wireless Ethernet Extender; otherwise, random lightning could easily cause
fatal damage to the unit.
WARNING: EMD (Lightning) DAMAGE IS NOT COVERED UNDER
WARRANTY.
2. Users MUST use the power cord and PoE injector shipped in the box with the
Wireless Ethernet Extender. Using other options will damage the unit.
Page 5
724-746-5500 | blackbox.com
Chapter 2: Preparing for Installation
What‘s Included
Your package should contain the following items. If anything is missing or
damaged, contact Black Box Technical Support at 724-746-5500 or
info@blackbox.com.
The LWE120A, LWE120AE, and LWE120UK packages contain the following items:
• (1) IEEE 802.11n Wireless Ethernet Extender
• (1) pole-mounting ring
• (1) 24-VDC power cord and PoE injector
• (1) ferrite suppression core
• (1) grounding wire
• This printed quick installation guide
The LWE120A-KIT and LWE120UK-KIT packages contain two each of the items
listed above for LWE120A, LWE120AE, and LWE120UK.
To download the user manual from the Web site:
1. Go to www.blackbox.com
2. Enter the part number (LWE120A) in the search box:
3. Click on the “Resources” tab on the product page, and select the document
you wish to download.
NOTE: Users MUST use the power cord and PoE injector shipped in the box with
the Wireless Ethernet Extender. Using other options will damage the unit.
Page 6 724-746-5500 | blackbox.com
Chapter 2: Preparing for Installation
Figure 2-1. Pole-mounting ring.
Figure 2-2. Power cord and PoE injector.
Page 7
724-746-5500 | blackbox.com
Chapter 3: System Installation
3. System Installation
Connect up
1. The bottom of the Wireless Ethernet Extender is a movable cover. Grab the
cover and pull it back harder to take it out as the figure shown below.
Figure 3-1. Removing the bottom cover from the extender.
2. Plug a standard Ethernet cable into the RJ-45 port.
Figure 3-2. Plugging a standard Ethernet cable into the RJ-45 port.
3. Slide the cover back and press down the lock button to seal the bottom of the
Wireless Ethernet Extender.
Figure 3-3. Replacing the bottom cover.
Page 8 724-746-5500 | blackbox.com
Chapter 3: System Installation
Using the Grounding Wire
The extender is equipped with a grounding wire. Be sure to properly connect the
extender, cables, and PoE injector to earth ground to protect against surges or
ESD during normal use.
1. Remove the screw on the grounding point at the bottom of the Wireless
Ethernet Extender.
Remove the
grounding screw
Figure 3-4. Grounding point on the extender.
2. Put the grounding wire on the grounding point at the bottom of the Wireless
Ethernet Extender. Then screw the grounding wire to tighten up.
Figure 3-5. Tighten the grounding wire.
3. Connect the grounding wire to earth ground.
Page 9
724-746-5500 | blackbox.com
Chapter 3: System Installation
Mount the AP on a Pole
1. Turn the Wireless Ethernet Extender over. Put the pole mounting ring through
the middle hole of it.
NOTE: Unlock the pole mounting ring with a screw driver before putting it
through the device as the following right picture shows.
Figure 3-6. Installing the pole mounting ring on the extender.
2. Mount the Wireless Ethernet Extender steadily to the pole by locking the pole
mounting ring tightly.
Figure 3-7. Extender mounted on a pole.
Page 10 724-746-5500 | blackbox.com
Chapter 3: System Installation
Power Up
1. Plug the power cord into the DC port of the PoE injector as the following
picture shows.
Figure 3-8. Power cord plugged into the injector’s DC port.
2. Use an Ethernet cable to connect the Wireless Ethernet Extender to the “POE”
port of the PoE injector as shown next.
Figure 3-9. Power up the extender.
3. Connect the power plug to a power socket. The Wireless Ethernet Extender will
be powered up immediately.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Extensor de Black Box
Black Box
Black Box IC500A Manual de usuario
Black Box
Black Box CampusLIGHT LCL114A-FEMM Manual de usuario
Black Box
Black Box CAT5 ClassWork Plus Multiloop Manual de usuario
Black Box
Black Box AC1070A Manual de usuario
Black Box
Black Box ME772A-M/FSP Manual de usuario
Black Box
Black Box ACS2001A-R3 Manual de usuario
Black Box
Black Box AC555A Manual de usuario
Black Box
Black Box IC443A-R2 Manual de usuario
Black Box
Black Box 4KDPKVMXT-100M Manual de usuario
Black Box
Black Box ServSwitch ACS253A-CT Manual de usuario
Black Box
Black Box ACU5050A Manual de usuario
Black Box
Black Box LB200A Manual de usuario
Black Box
Black Box LBNC300A Manual de usuario
Black Box
Black Box LB300A-RACK Manual de usuario
Black Box
Black Box ServSwitch ACX310 Manual de usuario
Black Box
Black Box IC490A Manual de usuario
Black Box
Black Box ACS253A-CT Manual de usuario
Black Box
Black Box ACS2009A-R2 Manual de usuario
Black Box
Black Box IC569A Manual de usuario
Black Box
Black Box AC2000A Manual de usuario
