Black & Decker BWDS Manual de usuario
Page 1
INSTRUCTION MANUAL
WASHER DRYER STAND
Thank you for choosing BLACK+DECKER!
PLEASE READ BEFORE RETURNING THIS PRODUCT FOR ANY
REASON.
If you have a question or experience a problem with your BLACK+DECKER
purchase, go to www.blackanddecker.com/instantanswers
If you can’t find the answer or do not have access to the Internet, call
844-299-0879 from 10:30 a.m. to 6:30 p.m. EST Mon.-Fri. to speak with an
agent. Please have the catalog number available when you call.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
CATALOG NUMBER
BWDS
Page 2
Thank you for purchasing our
BLACK+DECKER product. This
easy-to-use manual will guide you
in getting the best use of your
washer dryer stand.
Remember to record the model and
serial numbers. They are on a label
on the rear.
Staple your receipt to your manual. You will need it to obtain warranty service.
Model number
Serial number
Date of purchase
SAFETY INFORMATION
Important Safety Instructions.............................................................................................................................................. 3
SET UP & USE
Parts List.................................................................................................................................................................................... 4-6
Assembly Instructions........................................................................................................................................7-17
CLEANING & CARE..............................................................................................................................................18
TROUBLESHOOTING & WARRANTY
Important ...................................................................................................................................................................18
Limited Warranty......................................................................................................................................................................19
CONTENTS
PRODUCT REGISTRATION
Page 3
1. READ ALL INSTRUCTIONS BEFORE USE.
WARNING:
• Maximum Weight for Dryer Rack 60 lbs. Do not exceed maximum weight limit.
• This washer dryer stand must be anchored to a wall using anti-tip brackets to
avoid tipping.
RISK OF PERSONAL INJURY OR DEATH. THE STAND MUST BE SECURED TO
RIGID FRAMING MEMBER OF ADJACENT WALL BEFORE USING.
• Some assembly parts may cause choking. Keep away from children.
• Do not lean on, or allow children to play or climb on the washer dryer stand. Do not
allow children to hang from the door of the dryer when seated on the top of the
washer dryer stand because this could cause tipping.
SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY
WARNING
When using the washer dryer stand , basic safety precautions
should be followed, including the following:
DANGER
DANGER - Immediate hazards
that WILL result in severe
personal injury or death
WARNING
WARNING - Hazards or unsafe
practices that COULD result in
severe personal injury or death
CAUTION
CAUTION - Hazards or unsafe
practices that COULD result in
minor personal injury
IMPORTANT SAFETY INSTRUCTIONS
SAFETY INFORMATION
Page 4
PARTS LIST
Tools Required: Screwdriver and Drill.
NOTE:
15S = 2 short butterfly screws. Used for installing Support Rails, to L-BP and R-BP
pieces. Must be inserted so that wing is on exterior side of unit.
25S = 14 short buttery screws. Used for installing Connecting Rails, L-BP and R-BP
pieces to vertical rails. Must be inserted so that wing is on exterior side of unit.
35M = 4 medium buttery screws. Connects diagonal support rails. Must be inserted
so that wing is on rear of unit.
45L = 6 long buttery screws. Must be inserted through vertical rail rst then
tightened into Reinforcing Bars.
SET UP & USE
25S
25S
25S
15S
25S
25S
25S
25S
15S
Anti-tip Bracket
Connecting Rail
Connecting Rail
Anti-tip Bracket
35M
35M
35M
35M
25S
45L
45L
45L
LF1-1
RF1-1
RB2-1
LB2-1
LF1-2
RF1-2
L-BP
R-BP
RB2-2
LB2-2
L-BP R-BP
Reinforcing Bar
Reinforcing Bar
Support Rail
Support Rail
Page 5
L-BP R-BP R-BP
L-BP
SET UP & USE
Diagonal Support Rail
Connecting Rail
Support Rail
Anti-tip Bracket
Lag Type Screws
Reinforcing Bar
35M 45L25S15S
Non-slip Pad
LF1-1 RF1-1
RB2-1 LB2-1
LB2-2 RB2-2
LF1-2 RF1-2
Page 6
SET UP & USE
ID DESCRIPTION QUANTITY
L-BP LEFT DRYER SUPPORT 1
R-BP RIGHT DRYER SUPPORT 1
NON-SLIP PAD 4
L-BP LEFT BASE PLATE 1
R-BP RIGHT BASE PLATE 1
LF1-1 UPPER LEFT FRONT VERTICAL POLE 1
RF1-1 UPPER RIGHT FRONT VERTICAL POLE 1
LB2-1 UPPER LEFT BACK VERTICAL POLE 1
RB2-1 UPPER RIGHT BACK VERTICAL POLE 1
LB2-2 LOWER LEFT BACK VERTICAL POLE 1
RB2-2 LOWER RIGHT BACK VERTICAL POLE 1
LF1-2 LOWER LEFT FRONT VERTICAL POLE 1
RF1-2 LOWER RIGHT FRONT VERTICAL POLE 1
REINFORCING BARS 3
ANTI-TIP BRACKET 2
CONNECTING RAIL 2
SUPPORT RAIL 2
DIAGONAL SUPPORT RAIL 1
45L BUTTERFLY SCREWS (Long)-45mm 6
35M BUTTERFLY SCREWS (Medium)-35mm 4
25S BUTTERFLY SCREWS (Short)-25mm 14
15S BUTTERFLY SCREWS (Short)-15mm 2
LAG TYPE SCREWS 2
Parts are labeled according to the ID in the above Chart. ID number is stamped on the
top of the vertical poles. The DOWN arrow indicates lower parts and the UP arrow
indicates upper parts.
NOTE: There are 4 sizes of butterfly screws. It is important to use the correct screw
(45L, 35M, 25S, 15S) and insert in the location as directed in the instructions.
To install the butterfly screw, insert and turn to the right until the entire threaded part
of the screw is fully inserted.
Page 7
SET UP & USE
ASSEMBLY INSTRUCTIONS
1. Using the diagram below as reference to position the poles, INSERT LB2-2
(LOWER LEFT BACK VERTICAL POLE) and LF1-2 (LOWER LEFT FRONT
VERTICAL POLE) into L-BP LEFT BASE. The base of the poles should be
positioned between the L-BP slots and aligned with the holes.
Use 25S (BUTTERFLY SCREW) to secure on each side. They should be inserted
from the outside of L-BP and inserted fully through the holes of the poles to
secure.
NOTE: Follow the same steps to assemble the right side.
2. Insert LB2-1 (UPPER LEFT BACK VERTICAL POLE) into LB2-2 (LOWER LEFT
BACK VERTICAL POLE).
Insert LF1-1 (UPPER LEFT FRONT VERTICAL POLE) into LF1-2 (LOWER LEFT
FRONT VERTICAL POLE).
LF1-2
LB2-2
L-BP
25S
Closeup of LF1-2 and
LB2-2 being inserted into
L-BP . Make sure holes are
aligned when inserted.
LB2-2
25S
LF1-2
L-BP
LB2-1
LB2-2
LF1-2
LF1-1
Page 8
SET UP & USE
Line up the holes of one side of a SUPPORT RAIL, then the CONNECTING RAIL with
the holes on the exterior side of LF1-1 (UPPER LEFT FRONT VERTICAL POLE)
and LB2-1 (UPPER LEFT BACK VERTICAL POLE). Secure with 25S (BUTTERFLY
SCREW).
Line up the middle hole of the SUPPORT RAIL with the hole on the outside of LF1-2
(LOWER LEFT FRONT VERTICAL POLE), Secure with 25S (BUTTERFLY SCREW).
Line up the last hole of the SUPPORT RAIL with the hole on the outside of L-BP
(LEFT BASE), Secure with 15S (BUTTERFLY SCREW).
NOTE: Follow the same steps to assemble the right side.
25S
15S
L-BP
Support Rail
Support Rail
25S
Connecting Rail
Support Rail
25S
LF1-1
LB2-1
LF1-2
Page 9
3. Attach REINFORCING BARS to the top and bottom of the left BACK pole and the
top of the LF1-1 as shown below.
Attach one side of a REINFORCING BAR to LB2-1 . Align the holes and Insert 45L
(BUTTERFLY SCREW) through LB2-1 first and then through the reinforcing bar.
Attach one side of a REINFORCING BAR to LF1-1 . Align the holes and Insert 45L
(BUTTERFLY SCREW) through LF1-1 rst and then through the reinforcing bar.
Attach one side of the remaining REINFORCING BAR to LB2-2 . Align the holes
and Insert 45L (BUTTERFLY SCREW) through LB2-2 rst and then through the
reinforcing bar.
SET UP & USE
REINFORCING BAR
REINFORCING BAR
45L
45L
LB2-1
LB2-2
LF1-1
NOTE: The wings of 45L screw must keep vertical rather than horizontal so it does
not obstruct the installation of the DRYER SUPPORT.
45L
CORRECT INCORRECT
Page 10
Follow the same steps to assemble the right side:
Attach another side of a REINFORCING BAR to RB2-1 . Align the holes and Insert
45L (BUTTERFLY SCREW) through RB2-1 first and then through the reinforcing bar.
Attach another side of a REINFORCING BAR to RF1-1 . Align the holes and Insert
45L (BUTTERFLY SCREW) through RF1-1 rst and then through the reinforcing bar.
Attach one side of the remaining REINFORCING BAR to RB2-2 . Align the holes
and Insert 45L (BUTTERFLY SCREW) through RB2-2 rst and then through the
reinforcing bar.
RB2-1
RB2-2
RF1-1
SET UP & USE
Otros manuales para BWDS
1
Tabla de contenidos
Idiomas:
Otros manuales de Rack y soporte de Black & Decker
