BioTools BS-3030 Series Manual de usuario

BS-3030 Series

Zoom Stereo Microscope

Instruction Manual

BS-3030A BS-3030AT BS-3030B BS-3030BT

This instruction manual is for the stereo microscope BS-3030 series. To ensure the safety and

obtain optimum performance and familiarize yourself fully with the use of this microscope, we

recommend that youread this manual thoroughly beforeoperating the microscope. Please keep

this instruction manual in an easily accessible place near the microscope for future reference.

BioToolsInc.

0303-SBTNETNOC

Before use......................................................................... 1

1.Nomenclature.....................................................................2

2.Assemblage........................................................................3

3.Operation

3-1.Use the black and white work board...............................4

3-2. Adjust the degree of tightness of the focusingarm.........4

3-3.Set the specimen slide...................................................4

3-4.Adjust the specimen slide..............................................4

3-5.Adjust the interpupillary distance....................................5

3-6.Mount and removethe optional eyepiece micrometer......5

3-7.Use auxiliary objective...................................................5

3-8.Mount C type photo set and TV set.................................5

3-9.Adjust the focus of TV set..............................................5

4.USE Microscope base

(1)Nomenclature..................................................................6

(2)Operation........................................................................6

5.Technical parameter............................................................7

6.Troubleshooting..................................................................8

0303-SBESUEROFEB

Operation

1) As microscope is a precision instrument, handle with care, avoiding impact or

abruptmovementduringtransportation.

2) Microscope ought to be placed inadry and clean place. Do not expose the

microscope in the sun directly. Avoid high temperatureandviolent vibration.

Usually, followingenvironment is required indoortemperature: 0°C - 40 °C, Max.

relative humidity:85%.

3) To keepthe imageclear, do notleave fingerprints or stains on the surfaces of

the lens.

4) Beforeuse,pleasecheck the power supply in compliance with the microscope

power required.

5) Never turn the leftand rightfocusingknob in theadversedirection at the same

time, otherwise the microscopewill be damaged.

6) Whenusephotoset to captureimage,please ensure the stability of microscope,

make sure the mainbody inclinedless than 3°.

7) When use camera with C-mount, the camera sensor size should be less than

2/3”, weightnot more than2.5kg.

Maintenance

1) All lenses must be keptclean. Fine dust on the surface of the lens should be

blown off with hand blower or wipedoff gently withasoft lenstissue;

Fingerprints or oil marked on it should be wiped off with a tissuemoistened with

a small amount of xylene or a 3:7 mixture of alcoholand ether.

2) Never use the organicsolution to cleanthe othersurface (especially the plastic

surfaces). If necessary, please choosethe neutraldetergent.

3) Do not take the microscopeapart for fearing that it is damaged.

4) After using, coverthe microscopewith the dust-coverprovidedand store it in a

dry and cleanplace free from moisture to prevent rust.

1. Nomenclature

Eyepiece

Head lock

screw

Zoom control knob

Focusing

Head

Base

Clip

Black and white work board

Lock

screw C-mount

Focusing ring

PK-mount

2. Assemblage

The following diagram for the installation, the number representatives the order.

Before installing, it should ensure thatall connections has clean surface, theinstallationshould

be taken to avoid the surface of the lens was dirty or scratched.

C type

camera

C type

mount

PK-mount

Eyepiece

Head

Head lock screw

Base

Clip

Black and white work

board

*1)Connect theC-mount to the camera, Then connect the camera to the PK- Mount.

Fig.3

3. Operation

Fig.1

3.1 Use black and white work

board

(1) If the specimen is white or transparent, make the black one as

background, to enhance the contrast.

(2) Take off or changethework board, move the work board (Fig.1)

make one sidedown, then the other side will be up.(Fig. 1)

Adjust the degree of tightness of the focusing

arm.

Loose

Fig.2

Tension

(1) If you want to adjust tightness of the focusing arm, you can

hold one of the focusing knobs and turn another one to attain a

suitable tightness. The degree of tightness relies on the

direction to be turned. The reverse direction is tight, otherwise, is

loose.

(2)The suitable position of tightness can make the adjustment

more comfortable and prevent the focusing bracket from slipping

down by its weight during the observation. (Fig.2)

Set the specimenslide

(1) Set thespecimen on the center of stage plate. If necessary,

clamp the slide with the clips.

(2)Turn on the light.

Left eyepiec e

diopter adjustable

loop

Right eyepiece

diopter adjustabl e

loop

Fig.3

Adjustthe specimenslide

(1) Turn the zoom control knob to the maximum magnification.

(2) Turn the diopteradjusting rings to the zero.

(3) Observe the specimen through the right eyepiece and make

the imageclear by turning the focusing knob.

(4) Rotate the zoom control knob to theminimum magnification.

(5) Observe the specimen through the right eyepiece and make

the imageclear by turning the right diopter adjusting ring.(Fig.3)

(6) Re-do the step(3)and (5) till the right adjusting ring is more precise.

(7) Do the step (4) and make the image clear which is observed

through the left eyepiece by turning the left diopter adjusting ring.

(Fig.3)

Adjust the interpupillary

distance

(1) Adjust the prism housing along the direction of arrow of

the Fig.4 till the observation is comfortable.

Fig.4

Fig.5

With scale

Screw in

Screw out

Mount and Remove the Optional Eyepiece

Micrometer

(1) Turn and remove the mounting ring from the eyepiece.(Fig.5)

(2) Clean the eyepiece micrometer and mount it to the mounting

with the inscriptionside downward.

(3) Gently twist the mounting ring with the eyepiece micrometer

into the eyepiece till tightening securely.

(4) To remove the eyepiece micrometer, take down the mounting

ring by twisting and take out of the micrometer, and then wrap it.

Auxiliary

objecive

Fig.6

Fig.7

Fig.8

Use Auxiliary objective

(1) Connect the Auxiliary objective to the thread at the bottom

of the microscope head.

(2) 0.5x Auxiliary objective has long working distance. When use

0.5x auxiliary objective, release the lock screw on the arm by

a 4mm Allen key, move the focus arm up and fixed in the up

screw hole.(Fig 6)

0.75x auxiliary objective no need to remove arm.

MountPK-mountandphoto set

(1) Screw the PK-mount in the head, M28 screw, tight the

mount.(Fig.7)

(2) Loosen the screw on the PK-mount , take out the mount of C

type camera .

(3) Screw the C type mount in the TV photo set.

(4) Install the TV photo set into the PK-mount and lock the screw.

Focusing the TV photo set

(1) Turn the zoom control knob to the maximum magnification,

meanwhile, observe the TV set, adjust until the image is clear.

(2) Rotate the zoom control knob to the min.magnification. If the

image is not clear enough, adjust the part until the image clear.

(3) Redo the step (1), turn the zoom control knob to the maximum

magnification to check the image is clear or not. If not clear, redo

step(1)and (2), untilthe image is clear in all the zoom range.



4. Use Microscopestand

base

BS-3030

series

Makesurethe power is cut off when replace the fuse.

Make sure the earth wire is correctly connected.

Black and white stage plate, glass stage plate, diameter 95mm

4.1

Nomenclature

4.2 O

peration

Fig.10

Fig.11

Fig.9

2.1 Adjust the brightness of the bottom light or

top light

Turn the adjustable light knob, knob control

top light, knob control bottom light, along the

clockwise the brightness will be added, otherwise it

will be weakened. (Fig.10)

2.2 Replace the fuse

(1) Screw the fuse tube out withascrewdriver.

(2) Then pull the fuse out of the tube .

(3) Change with new fuse and mount it in an adverse

direction.

echnical

arameter

5.1 Optical parameter

Zoom

magnification

Working

distance

(mm)

Eyepiece Eyepiece (optional)

WF10X/22mm WF15X/16mm WF20X/12mm

magnification Field of

view(mm) magnification Field of

View(mm)

magnification Field of

view(mm)

0.67X

105

6.7X 32.8 10.05X 23.9 13.4X 17.9

0.7X7X 31.4 10.5X 22.8614X17.1

0.8X8X 27.5 12X 20 16X15

1X 10X 22 15X 16 20X12

1.5X15X 14.722.5X 10.7 30X8

2X 20X 11 30X 8 40X6

3X 30X 7.3 45X 5.3 60X4

4X 40X 5.5 60X 4 80X3

4.5X45X 4.9 67.5X 3.6 90X2.7

5.2 Auxiliary objective

standard(optional)

Magnification Working

distance(mm) Magnification Working

distance(mm)

0.3X287 0.75X 117

0.4X217 1.5X47

0.5X177 2X 26

Working distance is fixed regardless of the magnification factor.

Total mag.= Zoom mag. X Eyepiece mag. X Auxiliary objective mag.

Diameter of field of view(mm)=

Fieldnumber of eyepiece

Zoom mag.X Auxiliaryobjective mag.

5.3 Photoadapter mag.= Zoom mag.(X Auxiliary objective mag.)X Eyepiece

mag.

5.4 Photo set zoom mag.= Zoom mag.(XAuxiliary objective mag.) X CTV mag .X C

type photo tube

mag.

rouble shooting

The performance of the microscope can't be made fullybecause of unfamiliar using,

this following tablewill give some advice.

noituloSesuaCelbuorT

1. Optical system

(1) Brightness is too bright or too dark Brightness adjust not well Make right adjustment

(2)Dirt appears in the field of view

Dirt on the specimen Clean the specimen

Dirt on the surface of eyepiece Clean the surface

Dirt on the surface of the objective Clean the objective

Dirt on the working stage Clean the working stage

(3)Double image

Interpupillary distance is not correct Readjust it

Dioper adjustment is not correct Readjust it

Magnification of each eyepiece is not

the same size

Mount the same size eyepiece

(4)Image is not clear Dirt on the surface of the objective Clean the objective

(5)Image is not clear whilethe focus

changing

Diopter adjustment is not correct Readjust the diopter

Focus is not correct Readjust the focus

(6)The image on the monitor is not

clear whenthe focusing knob is

turned

The

focus

video

is not correct

Readjust the focus of video to

a correct position

2. Electrical

system

(1) Bulb does not work when the

switch is on

The bulb is notinserted correctlyInsert it correctly

Bulb is wrong Replace bulb

Fuse is broken Replace fuse

There is something impede the

light

Clean the working stage

(2)bulb is burned out suddenly

The voltage is too high Use voltage regulator

Use the wrong bulb Replace withacorrectone

(3) fusealwaysburned out The voltage is too high Use voltage regulator

(4) the bulb flickers or the

Brightness is unstable

The bulb willburn out soon Replace withanew one

The bulb was not inserted

correctly

Insert I correctly

3. F

ocusing

(1) the focusing knob is not smooth The focusing knob is too tight Loosen it to a suitable

(2)the image is obscure because

of the head slipping down by

itself during observation

The focusing knob is too loose Tight it toasuitable position

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Microscopio de BioTools

BioTools

BioTools BS-3047 Series Manual de usuario

BioTools

BioTools BS-2090 Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario