Biostar P4TGE Manual de usuario

FCC Statement and Copyright

This equipment has been tested and found to comply with the limits of a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. There is no guarantee that interference will not occur in a

particular installation.

The vendor makes no representations or warranties with respect to the

contents here of and specially disclaims any implied warranties of

merchantability or fitness for any purpose. Further the vendor reserves the

right to revise this publication and to make changes to the contents here of

without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole is not allowed without

first obtaining the vendor’s approval in writing.

The content of this user’s is subject to be changed without notice and we

will not be responsible for any mistakes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

ENGLISH..................................................................................................... 1

P4TGE Features.................................................................................................................1

Package contents..............................................................................................................3

Layout of P4TGE................................................................................................................4

CPU Installation.................................................................................................................5

DDR DIMM Modules: DDR1-2 ...........................................................................................6

Jumpers, Headers, Connectors & Slots..........................................................................7

ESPAÑOL ................................................................................................. 15

Características del P4TGE..............................................................................................15

Contenido del Paquete.................................................................................................... 17

Disposición del P4TGE...................................................................................................18

Instalación de la CPU......................................................................................................19

Módulos DDR DIMM: DDR1-2.........................................................................................20

Puentes, Cabezales, Conectores y Ranuras................................................................. 21

TROUBLE SHOOTING............................................................................. 29

SOLUCIÓN DE PROBLEMAS ................................................................. 30

iip

iio

English

P4TGE Features

 Use Intel 845GE/ ICH4 Chipset, Winbond W83627, 1394A Chip, SATA/

RAID Chip (Optional).

 Contains on board I/O facilities, which include one serial port, one VGA port,

a parallel port, a PS/2 mouse port, a PS/2 keyboard port, audio ports, USB

ports and a game port .

 Supports the Intel Pentium 4®(Socket 478) processor up to 3.06GHz.

 Supports Intel Pentium 4 processor with Hyper-Threading.

 Supports Ultra 100/66/33, BMIDE and PIO modes.

 Supports 2 DDR266/333 MHz devices, running at 400/533 MHz Front Side

Bus frequency.

 Supports five 32-bit PCI Bus slots, one AGP Slot, and one CNR Slot (Type

A only) .

(If the function CODEC is onboard, then the CNR slot only supports

slave card. But if the H/W Audio is onboard, then the CNR slot

supports only primary card.)

 Supports USB1.1 and USB2.0.

 Complies with PC ATX form factor specifications.

 Supports popular operating systems such as Windows 98, Windows NT,

Windows 2000, Windows ME, Windows XP, LINUX and SCO UNIX.

 DIMM Power Selection by BIOS setup to adjust DDR DIMM voltage. (If you

meet the DDR DIMM compatible program, try to adjust the DDR Voltage to

fix the compatible program.)

 Intel®AC’97 2.2 compatible.

 High S/N ratio meets PC 99 requirements.

 6CH Audio Codec, applicable for leading motherboard chipsets.

iip

iio

 Supports SPDIF-Out function.

 Line-in phone-jack share with rear out .

 Mic-in phone-jack share with Bass and Center.

 CMI 8738 Hardware Audio Features (Optional):

 6CH DAC for AC3® 5.1CH purpose.

 HRTF-based 3D positional audio, supporting DirectSound™ 3D and

A3D™ interface.

 Supports 4.1/5.1 speakers, C3DX positional audio in 4/ 6 CH

speaker mode.

 Serial ATA-Raid Features (Optional):

 Single chip, high performance SATA-RAID implementation.

 Built in 2 channels SATA PHY, which satisfy SATA 1.0 specification

and can transfer data with 1.5GHz speed.

 Additional one parallel ATA interface which satisfy ATA 133

specification.

 Bus mastering design takes full advantage of multi-tasking,

multi-threading operating systems and greatly improves

performance.

 Provides advance chained packet commands for independent ATA

operations.

 Compatible with the latest PCI IDE, ATA 7 and enhanced IDE

specifications.

 Supports ATA proprosal PIO Mode 0, 1, 2, 3, 4, Ultra DMA Mode 0,

1, 2, 3, 4, 5, 6. The IDE drive transfer rate is capable of up to 150

MB/sec.

 Automatically detects whether or not the cable is suitable for mode

3, 4, 5, 6 of Ultra DMA.

 Compliance with the PC2000, WHQL hardware requirements.

iip

iio

Package contents

 HDD Cable X 1

 FDD Cable X 1

 Fully Setup Driver CD X 1

 USB Cable X 2 (Optional)

 IEEE1394 Cable X1 (Optional)

 Serial ATA Cable X1 (Optional)

 SPDIF OUT Cable X1 (Optional).

iip

iio

Layout of P4TGE

JKBMS1

Mouse

JUSBLAN1

USB & LAN

JCOM1

JPRNT1

JCOM2

Parallel Port

Speaker

Out

Line-In

MIC-In

Game Port

JGAME1

JVGA1

COM1VGA1

JKBV1

JUSBV1

INTEL

845GE

CPU

Socket 478

CPU1

JATXPWR2

DDR1

DDR2

JATXPWR1

FDD1

JGAME1

IDE1IDE2

AGP SLOT

PCI1

PCI2

PCI SLOT

PCI4

PCI SLOT

PCI5

PCI3

LAN Chip

JAUDIO1

213

Codec

JPANEL1

JCDIN1

Hardware

Audio

CNR SLOT

CNR1

J1394A1

J1394B1 J1394C1

JWOL1

JUSB4

JUSB3

1394

CHIP

RAID1

BAT1

ICH4

JSFAN11

JCMOS1

Serial

ATA

Controller

JSATA2

JSATA1

BIOS

JCL1

Winbond

I/O

JSPDIF_OUT 1

JUSBV3_4

Primary IDE Conn.

Secondary IDE Conn.

Floppy Disk Conn.

iip

iio

CPU Installation

1. Pull the lever sideways away from the socket then raise the lever up

to 90-degree angle.

2. Locate Pin A in the socket and lock for the white dot or cut edge in

the CPU. Match Pin A with the white dot/cut edge then insert the

CPU.

3. Press the lever down. Then Put the fan on the CPU and buckle it

and put the fan’s power port into the JCFAN1, then to complete the

installation.

CPU/ System Fan Headers: JCFAN1/ JSFAN1

CPU

JCFAN1

Ground

12V

Sense

JSFAN1

Ground

12V

Sense

iip

iio

DDR DIMM Modules: DDR1-2

Supports DDR200/266/333 unregistered 184-pin non-ECC DDR

SDRAM DIMMs. Does not support double-size x16 DDR DIMMs.

DRAM Type: 64MB/ 128MB/ 256MB/ 512MB/ 1GB DIMM Module (184

pin)

DIMM Socket

Location DDR Module Total Memory

Size (MB)

DDR 1 64MB/128MB/256MB/512MB/1GB

DDR 2 64MB/128MB/256MB/512MB/1GB

Max is

2GB

* The list shown above for DRAM configuration is only for reference.

 If use FSB 400MHz CPU, the memory run only at DDR200/266.

 If use FSB 533MHz CPU, the memory run only at DDR266/333.

How to install a DIMM Module

1. The DIMM socket has a

“Plastic Safety Tab”, and the

DIMM memory module has an

“Asymmetrical notch”, so the

DIMM memory module can only

fit into the slot in one direction.

2. Push the tabs out. Insert the

DIMM memory modules into the

socket at a 90-degree angle, then

push down vertically so that it will

fit into the place.

3. The Mounting Holes and plastic

tabs should fit over the edge and

hold the DIMM memory modules

in place.

iip

iio

Jumpers, Headers, Connectors & Slots

Hard Disk Connectors: IDE1/ IDE2

The motherboard has a 32-bit Enhanced PCI IDE Controller that

provides PIO Mode 0~4, Bus Master, and Ultra DMA / 33/ 66/ 100

functionality. It has two HDD connectors IDE1 (primary) and IDE2

(secondary).

The IDE connectors can connect a master and a slave drive, so you can

connect up to four hard disk drives. The first hard drive should always be

connected to IDE1.

Serial ATA Connector: (JSATA1/ JSATA2) (Optional)

The motherboard has a PCI to SATA Controller with 2 channels SATA

interface, it satisfies the SATA 1.0 spec and can transfer data with

1.5GHz speed. For more details, please refer to the next chapter

(FastTrak 376).

Raid Connector: RAID1 (Optional)

This connector supports RAID0 or RAID1 configuration through the

onboard Serial ATA (FastTrak 376) controller chip. You can use the

IDE feature to set up a disk array configuration and to support additional

IDE devices. However, it can only support master mode IDE HDD.

Floppy Disk Connector: FDD1

The motherboard provides a standard floppy disk connector that

supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This

connector supports the provided floppy drive ribbon cables.

Communication Network Riser Slot: CNR1

The CNR specification is an open Industry Standard Architecture, and it

defines a hardware scalable riser card interface, which supports audio,

network and modem only (slave card only) .

(If the function CODEC is onboard, then the CNR slot only support

slave card. But if the H/W Audio is onboard, then the CNR slot

support only primary card.)

iip

iio

Accelerated Graphics Port Slot: AGP1

Your monitor will attach directly to that video card. This motherboard

supports video cards for PCI slots, but it is also equipped with an

Accelerated Graphics Port (AGP). An AGP card will take advantage of

AGP technology for improved video efficiency and performance,

especially with 3D graphics.

Peripheral Component Interconnect Slots: PCI1-5

This motherboard is equipped with 5 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for

expansion cards, which has, supplanted the older ISA bus standard in

most ports. This PCI slot is designated as 32 bits.

Power Connectors: JATXPWR1/ JATXPWR2

Wake On LAN Header: JWOL1

WOL1

5V_SB Wake up

Ground

JATXPWR1

(ATX Main Power Conn.)

JATXPWR1

(ATX Main Power Conn.)

JATXPWR2

(ATX 12V Power Conn.)

Tabla de contenidos

Idiomas:

Otros manuales de Placa madre de Biostar

Biostar

Biostar 945GC MICRO 775 Guía del usuario

Biostar

Biostar NF325-A7 Guía del usuario

Biostar

Biostar P4 VTB Manual de usuario

Biostar

Biostar MCP6P-M2 Guía del usuario

Biostar

Biostar A780G-M2-SE Guía del usuario

Biostar

Biostar P4TGT Manual de usuario

Biostar

Biostar M6TSS Manual de usuario

Biostar

Biostar M7VIGD Manual de usuario

Biostar

Biostar GF8100 M2G PLUS - BIOS Manual de usuario

Biostar

Biostar K8T800-A7A Manual de usuario

Biostar

Biostar M6TZE Manual de usuario

Biostar

Biostar TA785G3 HD - BIOS Guía del usuario

Biostar

Biostar M6TZK Manual de usuario

Biostar

Biostar TZ68K Manual de usuario

Biostar

Biostar P4TDK Guía del usuario

Biostar

Biostar BI94GS-IAC Guía del usuario

Biostar

Biostar M7VIZ V8.X Manual de usuario

Biostar

Biostar TA785 A2+ Guía del usuario

Biostar

Biostar U8668 Grand Manual de usuario

Biostar

Biostar M7 VKD Manual de usuario

Biostar

Biostar P4TSE Pro Guía del usuario

Biostar

Biostar IDEQ 200V Guía del usuario

Biostar

Biostar M7TDA Manual de usuario

Biostar

Biostar U8798 Guía del usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario