Biostar P4 TGS Manual de usuario

FCC Statement and Copyright

This equipment has been tested and found to comply with the limits of a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. There is no guarantee that interference will not occur in a

particular installation.

The vendor makes no representations or warranties with respect to the

contents here of and specially disclaims any implied warranties of

merchantability or fitness for any purpose. Further the vendor reserves the

right to revise this publication and to make changes to the contents here of

without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole is not allowed without

first obtaining the vendor’s approval in writing.

The content of this user’s is subject to be changed without notice and we

will not be responsible for any mistakes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

ENGLISH..................................................................................................... 1

P4TGS Features.................................................................................................................1

Package contents..............................................................................................................1

Layout of P4TGS................................................................................................................2

CPU Installation.................................................................................................................3

SDR DIMM Modules: SDR1-2............................................................................................4

Jumpers, Headers, Connectors & Slots..........................................................................5

ESPAÑOL ................................................................................................. 10

Características del P4TGS..............................................................................................10

Contenido del Paquete.................................................................................................... 10

Disposición del P4TGS ................................................................................................... 11

Instalación de la CPU......................................................................................................12

Módulos SDR DIMM: SDR1-2..........................................................................................13

Conectores, Cabezales, Puentes y Ranuras.................................................................14

WARPSPEEDER ...................................................................................... 19

Introduction......................................................................................................................19

System Requirement....................................................................................................... 20

Installation........................................................................................................................20

Usage................................................................................................................................22

TROUBLE SHOOTING............................................................................. 30

SOLUCIÓN DE PROBLEMAS ................................................................. 31

iip

iio

English

P4TGS Features

 Use Intel 845GL/ ICH4 Chipset, ITE IT8712, LAN Chip- RTL8100B

(optional).

 Contains on board I/O facilities, which include one serial port, one VGA port,

a parallel port, a PS/2 mouse port, a PS/2 keyboard port, audio ports, USB

ports, a LAN port (optional) and a game port.

 Supports the Intel Pentium 4®(Socket 478) processor up to 3.06GHz.

 Supports Ultra 100/66/33, BMIDE and PIO modes.

 Supports USB2.0 High Speed Device.

 Supports up to 2 SDR 100/133 MHz (without ECC) devices, running at 400

MHz or Fuzzy 533 MHz Front Side Bus frequency.

 Supports one CNR Slot (Type A only), and three 32-bit PCI Bus slots.

 Complies with PC Micro-ATX form factor specifications.

 Supports popular operating systems such as Windows NT, Windows 2000,

Windows ME, Windows XP, LINUX and SCO UNIX.

 Intel®AC’97 2.2 compatible.

 High S/N ratio meets PC 99 requirements.

 6CH DAC, applicable for leading motherboard chipsets.

 Line-in phonejack share with rear out.

 Mic-in phonejack share with Bass & Center.

 Supports front audio pin head functions.

Package contents

 HDD Cable X 1, FDD Cable X 1, Fully Setup Driver CD X 1

 Flash Memory Writer for BIOS update X 1

iip

iio

 USB Cable X 2 (Optional)

 Rear I/O Panel for ATX Case X 1 (Optional)

Layout of P4TGS

JATXPWR2

JKBMS1

JPRNT1

JGAME_USB1

Mouse

JRJ45USB1

USB & LAN

SDR1

SDR2

JAUDIO1

JATXPWR1

LAN CHIP

JCDIN1

JCOM1

JVGA1

COM1

CNR1

WOL1

JUSB1

JCMOS1

JPANEL1

JSFAN1

JCFAN1

FDD1

Parallel Port

JUSBV4

JUSBV1

JUSB2

Game Port

Speaker

Out

MIC-In Line-In

JUSBV3

Socket 478

INTEL

845GL

INTEL

82801DB

(ICH4)

PCI1

PCI2

PCI3

IDE1IDE2

Codec

VGA1

213

ITE I/O

JSPDIF_OUT

BAT1

10 2

123

iip

iio

CPU Installation

1. Pull the lever sideways away from the socket then raise the lever up

to 90-degree angle.

2. Locate Pin A in the socket and lock for the white dot or cut edge in

the CPU. Match Pin A with the white dot/cut edge then insert the

CPU.

3. Press the lever down. Then Put the fan on the CPU and buckle it

and put the fan’s power port into the JCFAN1, then to complete the

installation.

CPU/ System Fan Headers: JCFAN1/ JSFAN1

CPU

JCFAN1

Ground

12V

Sense

JSFAN1

Ground

12V

Sense

iip

iio

SDR DIMM Modules: SDR1-2

DRAM Access Time: 3.3V Unbuffered PC100/ PC133 Type required.

DRAM Type: 64MB/ 128MB/ 256MB/ 512MB DIMM Module (168 pin)

DIMM Socket

Location SDR Module Total Memory

Size (MB)

SDR 1 64MB/128MB/256MB/512MB *1

SDR 2 64MB/128MB/256MB/512MB *1 Max is

1GB

* The list shown above for DRAM configuration is only for reference.

How to install a DIMM Module

1. The DIMM socket has a

“ Plastic Safety Tab”, and the

DIMM memory module has an

“Asymmetrical notch”, so the

DIMM memory module can

only fit into the slot in one

direction.

2. Push the tabs out. Insert the

DIMM memory modules into

the socket at a 90-degree

angle, then push down

vertically so that it will fit into

the place.

3. The Mounting Holes and

plastic tabs should fit over the

edge and hold the DIMM

memory modules in place.

iip

iio

Jumpers, Headers, Connectors & Slots

Hard Disk Connectors: IDE1/ IDE2

The motherboard has a 32-bit Enhanced PCI IDE Controller that

provides PIO Mode 0~4, Bus Master, and Ultra DMA / 33/ 66/ 100

functionality. It has two HDD connectors IDE1 (primary) and IDE2

(secondary).

The IDE connectors can connect a master and a slave drive, so you can

connect up to four hard disk drives. The first hard drive should always be

connected to IDE1.

Floppy Disk Connector: FDD1

The motherboard provides a standard floppy disk connector that

supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This

connector supports the provided floppy drive ribbon cables.

Communication Network Riser Slot: CNR1

The CNR specification is an open Industry Standard Architecture, and it

defines a hardware scalable riser card interface, which supports audio,

network and modem only.

Peripheral Component Interconnect Slots: PCI1-3

This motherboard is equipped with 3 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for

expansion cards, which has, supplanted the older ISA bus standard in

most ports. This PCI slot is designated as 32 bits.

Power Connectors: JATXPWR1/ JATXPWR2

JATXPWR1

(ATX Main Power Connector)

JATXPWR2

(ATX 12V Power Connector)

iip

iio

Wake On LAN Header: WOL1

Front USB Header: JUSB1/ JUSB2

5V/ 5VSB Selection for USB: JUSBV1/ 3/ 4

Digital Audio Connector: JSPDIF_OUT

WOL1

5V_SB Wake up

Ground

JUSB1/2

Pin Assignment Pin Assignment

910

+5V +5V

Data (-)Data (-)

Data (+) Data (+)

Ground Ground

Key NA

JUSBV1/3/4

Pin 1-2 on ==> 5V

Pin 2-3 on ==> 5V_SB

JSPDIF1

GND

Pin Assignment

VCC5

SPDIFO_OUT

iip

iio

Front Panel Connector: JPANEL1

Audio Subsystem: JAUDIO1/ JCDIN1

SPK ==> Speaker Conn.

HLED ==> Hard Driver LED

RST ==> Reset Button

IR ==> Infrared Conn.

SLP ==> Sleep Button

PWR_LED ==> Power LED

ON/ OFF ==> Power-on Button

SPK

PWR_LED

HLED

SLP

RST

224

123

IRON/OFF

(+) (-)

(+) (-)(+)

JAUDIO1

(Front Audio Header)

JCDIN1

(CD-ROM Audio-In Header)

iip

iio

JAUDIO1

213

Mic In

Mic Power

RT Line Out

Reserved

LFT Line Out

RT Line In

LFT Line In

Assignment Ground

Audio Power

RT Line Out

Key

RT Line In

LFT Line In

Assignment

LFT Line Out

Pin 5, 9, 11, 13 are routed to Front Panel Audio Out.

Pin 6, 10, 12, 14 are routed from Front Panel Audio Out.

Front Panel Audio Connector/JumperBlock

910 Audio line out signals are routed

to the back panel audio line out connector.

Pin 5 and 6

Pin 9 and 10

Pin11 and 12

Pin13 and 14

Audio line out and mic in signals are

availablefor front panel audio connectors.

11 12

13 14

910

11 12

13 14

6No jumpers

installed

Jumper Setting Configuration

Otros manuales para P4 TGS

Tabla de contenidos

Otros manuales de Placa madre de Biostar

Biostar

Biostar M6VSA Manual de usuario

Biostar

Biostar Hi-Fi A88S2 Manual de usuario

Biostar

Biostar I91PL-A7 PCI-ED Manual de usuario

Biostar

Biostar J1800MH2 Guía del usuario

Biostar

Biostar 945GC-230 - BIOS Manual de usuario

Biostar

Biostar U8868 Guía del usuario

Biostar

Biostar K8T89-A7 Manual de usuario

Biostar

Biostar TA785GE - SETUP Guía del usuario

Biostar

Biostar B660GTN Manual de usuario

Biostar

Biostar P4 SFA Guía del usuario

Biostar

Biostar G31-M4 Manual de usuario

Biostar

Biostar U8598 Manual de usuario

Biostar

Biostar H310MHD PRO Manual de usuario

Biostar

Biostar TP55 - BIOS Guía del usuario

Biostar

Biostar H77MU3 Manual de usuario

Biostar

Biostar NF520-A2 TE - BIOS SETUP Manual de usuario

Biostar

Biostar N68S3B Manual

Biostar

Biostar TA785-A3 - BIOS Manual de usuario

Biostar

Biostar H61MGC Guía del usuario

Biostar

Biostar Hi-Fi Z97WE Guía del usuario

Biostar

Biostar U8868 Manual

Biostar

Biostar U8668-D Manual de usuario

Biostar

Biostar A58ML2 Guía del usuario

Biostar

Biostar Hi-Fi Z87W Guía del usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario