Biostar BVK2A Manual de usuario
Federal Communications Commission
(F.C.C) Statement
This device complies with Part 15 of the FCC Rules. Operation of this
device is subject to the following two conditions (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
Accessories This device has been tested and found to comply with the
limits of a Class B digital device, the accessories associated with this
equipment are as follows
1. Shielded serial cable. (Can be obtained from multiple retail outlets)
2. Shielded printer cable. (Can be obtained from multiple retail outlets)
3. Shielded video cable. (Can be obtained from multiple retail outlets)
4. Shielded power cord. (Provided by manufacturer)
These accessories are required to ensure compliance with FCC Rules. It
is the responsibility of the user to provide and use these accessories
properly.
This equipment has been tested and found to comply with the limits of a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. There is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, you are encouraged to try to correct the
interference by one or more of the following measures
1. Reorient / relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Caution Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
Disclaimer
The vendor makes no representations or warranties with respect to the
contents here of and specially disclaims any implied warranties of
merchantability or fitness for any purpose. Further the vendor reserves
the right to revise this publication and to make changes to the contents
here of without obligation to notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without
first obtaining the vendor’s approval in writing.
Trademarks and Remarks
MS-DOS, Windows, Windows NT, Windows 9X and Windows 2000 are
products of Microsoft Corp, with its ownership of trademark, and are
distributed by the vendor under a license agreement.
All trademarks used in this manual are the property of their respective
owners.
Copyright© 1999
All Rights Reserved
Canadian D.O.C. Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the radio interference regulations of
the Canadian Department of Communications.
Cet appareil numbérique n‘émet pas de bruits radioélectriques dépassant les
limites appliquées aux appareils numbériques de Class B préscrits dans le
réglement du brouillage radioélectrique edict par le minister Des Communications
du Canada.
Contents
Introduction.................................................................................1-1
1 Motherboard Description........................................................1-2
1.1 Features....................................................................................................1-2
1.1.1 Hardware..........................................................................................1-2
1.1.2 Software...........................................................................................1-4
1.1.3 Attachments.....................................................................................1-4
1.2 Motherboard Installation.........................................................................1-5
1.2.1 Layout of Motherboard....................................................................1-5
1.3 Motherboard Connectors.........................................................................1-6
1.3.1 Front Panel Connectors (JPANEL1 / JP5).......................................1-7
1.3.2 Floppy Disk Connector (FDD1)......................................................1-9
1.3.3 Hard Disk Connectors (IDE1/IDE2)................................................1-9
1.3.4 ATX 20-pin Power Connector (JATXPWR1)...............................1-11
1.4 Back Panel Connectors..........................................................................1-12
1.4.1 PS/2 Mouse / Keyboard CONN. JKBMS1...................................1-12
1.4.2 USB Connectors JUSB1...............................................................1-13
1.5 Serial and Parallel Interface Ports..........................................................1-16
1.6 CPU Installation.....................................................................................1-19
1.6.1 CPU Installation Procedure Socket A...........................................1-19
1.6.2 CPU Clock Selection JCLK1........................................................1-20
1.7 Jumper Settings......................................................................................1-21
1.7.1 CPU Fan Connector JCFAN1.......................................................1-21
i
Contents
1.7.2 System Fan Connector JSFAN1...................................................1-23
1.7.3 Wake-On MODEM Header JWOM1(Optional)...........................1-23
1.7.4 Wake-On-LAN Header JWOL1...................................................1-23
1.7.5 AMR Code Primary/Secondary Selection J4...............................1-23
1.7.6 CMOS Function Selection JCMOS1............................................1-24
1.8 DRAM Installation................................................................................1-25
1.8.1 DIMM............................................................................................1-25
1.8.2 How to install a DIMM Module....................................................1-27
1.9 Audio Subsystem...................................................................................1-28
1.9.1 CD Audio-In Connectors JCDIN1/JCDIN2.................................1-29
1.9.2 Telephony Connector JTAD1.......................................................1-29
1.9.3 AUX Audio in Connector JAUX1 (Optional)..............................1-29
1.9.4 Front Audio Connector JF_AUDIO (Optional)............................1-30
2. BIOS Setup..............................................................................2-1
2.1 Main Menu...............................................................................................2-3
2.2 Standard CMOS Features........................................................................2-6
2.3 Advanced BIOS Features........................................................................2-9
2.4 Advanced Chipset Features...................................................................2-13
2.5 Integrated Peripherals............................................................................2-18
2.6 Power Management Setup.....................................................................2-24
2.7 PnP/PCI Configurations.........................................................................2-30
2.8 PC Health Status....................................................................................2-33
2.9 Frequency / Clock Control....................................................................2-35
ii
Contents
2.10 Load Fail-Safe Defaults.......................................................................2-36
2.11 Load Optimized Defaults.....................................................................2-37
2.12 Set Supervisor / User Password...........................................................2-38
2.13 Save & Exit Setup................................................................................2-40
2.14 Exit Without Saving............................................................................2-41
3. Software Setup.........................................................................3-1
3.1 Software List............................................................................................3-1
3.2 Software Installation................................................................................3-2
3.3 Using Software........................................................................................3-3
4. Trouble shooting.......................................................................4-1
iii
Chapter 1 Motherboard Description
Introduction
System Overview
Thanks for buying this product! This manual was written to help you start using
this product as quickly and smoothly as possible. Inside you will find adequate
explanations to solve most problems. In order for this reference material to be of
greatest use, refer to the “expanded table of contents” to find relevant topics.
This board incorporates the system board, I/O, and PCI IDE into one board that
provides a total PC solution. The mainboard, AMD AthlonTM and DuronTM
processor based PC ATX system, supports single processors with ISA Bus, PCI
Local Bus, and AGP Bus to support upgrades to your system performance. It is
ideal for multi-tasking and fully supports MS-DOS, Windows, Windows NT,
Windows 2000, Novell, OS/2, Windows95/98, UNIX, SCO UNIX etc. This
manual also explains how to install the mainboard for operation, and how to setup
your CMOS configuration with the BIOS setup program.
1-1
Chapter 1 Motherboard Description
1 Motherboard Description
1.1 Features
1.1.1 ardware
PU
Single AMD Socket-A for Athlon TM (Thunderbird TM ) / Duron TM
processor Module-500MHz and faster.
200MHz System Interface speed.
Speed
Support 33MHz PCI Bus speed.
Support 4X AGP Bus.
DRAM Memory
Supports 8/16/32/64.......MB DIMM module socket.
Supports Synchronous DRAM (3.3V).
Support a maximum memory size of 768MB with SDRAM.
Shadow RAM
A memory controller provide shadow RAM and supports 8-bit ROM
BIOS.
Green Function
Support power management operation via BIOS.
Power down timer from 1 to 15 mins.
Wakes from power saving sleep mode at the press of any key or any
mouse activity.
BUS Slots
Provide one AGP slot and one AMR slot.
Five 32-bit PCI bus and one ISA slot bus master slots.
1-2
Chapter 1 Motherboard Description
Flash Memory
Support flash memory.
Support ESCD Function.
IDE Built-in On Board
Supports four IDE hard disk drives.
Supports PIO Mode 4, Master Mode, high performance hard disk drives.
Support Ultra DMA 33, 66 Bus Master Mode.
Supports IDE interface with CD-ROM.
Supports high capacity hard disk drives.
Support LBA mode.
P I-Based A 97 Digital Audio Processor (Optional)
AC 97 2.1 interface.
16 channels of high-quality sample rate conversion.
16x8 channel digital mixer.
Stereo 10 band graphic equalizer.
Sound Blaster® and Sound Blaster Pro® emulation.
S/PDIF output (allows standard interface to consumer electronics).
64-voice wavetable.
PC99 complaint and WHQL certified.
I/O Built-in On Board
Supports one multi-mode Parallel Port.
(1) Standard & Bidirection Parallel Port.
(2) Enhanced Parallel Port (EPP).
(3) Extended Capabilities Port (ECP).
Supports two serial ports, 16550 UART.
Supports one Infrared transmission (IR).
Supports PS/2 mouse and PS/2 keyboard.
Supports 360KB, 720KB, 1.2MB, 1.44MB, and 2.88MB floppy disk
drivers.
1-3
Chapter 1 Motherboard Description
Universal Serial Bus
Supports two back Universal Serial Bus (U.S.B.) Ports and two front
Universal serial Bus (U.S.B) Ports (Optional).
Supports 48 MHz USB.
Hardware Monitor Function
CPU Fan Speed Monitor.
System (Optional) and CPU Temperature Monitor.
System Voltage Monitor.
Dimensions (ATX form-factor)
22.2 cm X 30.5 cm (W x L)
1.1.2 Software
BIOS
AWARD legal BIOS.
Supports APM1.2.
Supports USB Function.
Supports ACPI.
Operating System
Offers the highest performance for MS-DOS, OS/2, Windows, Windows
NT, Windows 2000, Windows 95/98, Novell, UNIX, SCO UNIX etc.
1.1.3 Attachments
HDD Cable.
FDD Cable.
Flash Memory Writer for BIOS Update.
Retention Kits for CPU.
USB2 Cable (Optional).
Rear I/O Panel for ATX Case (Optional).
Fully Setup Driver CD.
1-4
Chapter 1 Motherboard Description
1.2 Motherboard Installation
1.2.1 Layout of Motherboard
Model No.BVK2A
1-5
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Placa madre de Biostar
Biostar
Biostar P35D2-A7 Guía del usuario
Biostar
Biostar TF7025-M2 Guía del usuario
Biostar
Biostar M7 VKQ Manual de usuario
Biostar
Biostar H61MLC2 Manual de usuario
Biostar
Biostar A770E3 Guía del usuario
Biostar
Biostar TB85-BTC Manual de usuario
Biostar
Biostar TA790GX A3+ Manual
Biostar
Biostar Hi-Fi H87S3 Guía del usuario
Biostar
Biostar K8T80-A7 Manual de usuario
Biostar
Biostar P4 SDR Manual de usuario
Biostar
Biostar M5SAA Manual de usuario
Biostar
Biostar M6SBA Instrucciones y recetas
Biostar
Biostar M7VIT 800 V7.X Manual de usuario
Biostar
Biostar I865G-M4 Guía del usuario
Biostar
Biostar P31-A7 Guía del usuario
Biostar
Biostar M6VCF Manual de usuario
Biostar
Biostar 945P-A7B Guía del usuario
Biostar
Biostar Z590I VALKYRIE Manual de usuario
Biostar
Biostar B360GT3S Manual de usuario
Biostar
Biostar TP43D2-A7 Guía del usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
