Bindicator Pulse Point LP-500ST Manual de usuario

Pulse Point™ LP-500ST

Installation & Operation Manual

IOM

622 Mary Street; Suite 101; Warminster, PA 18974

Phone: 267-673-8117 - Fax: 267-673-8118

Sa[email protected] -

www.cabriggs.com

CONTENTS

I. HANDLING AND STORAGE............................................................................................................................................................................1

Inspection and Handling

Disposal and Recycling

Storage

II. GENERAL SAFETY............................................................................................................................................................................................2

Authorized Personnel

Use

Misuse

III. PRODUCT DESCRIPTION..............................................................................................................................................................................3

Function

Applications

Features

Technical Specications

Figure 1: Temperature Table

Figure 2: Temperature Graph

IV. MECHANICAL INSTALLATION ....................................................................................................................................................................5

Guidelines

Mounting Considerations

Figure 3: High/Low Level Location

Figure 4: Mounting Position

V. ELECTRICAL INSTALLATION.........................................................................................................................................................................7

General Safety

Disconnect Requirements for Permanently Installed Equipment

Protective Earth Ground

Electrical Connections

Figure 5: Wiring

Figure 6: Fail-Safe Operation

VI. MAINTENANCE ...............................................................................................................................................................................................9

Preventative Maintenance

VII. TROUBLESHOOTING .................................................................................................................................................................................9

VIII. DIMENSIONAL DRAWINGS ..................................................................................................................................................................10

Pulse Point™ LP-500ST

Installation & Operation Manual

SAFETY SYMBOLS

WARNING:

IDENTIFIES CONDITIONS OR PROCEDURES, WHICH IF NOT

FOLLOWED, COULD RESULT IN SERIOUS INJURY.

CAUTION:

IDENTIFIES CONDITIONS OR PROCEDURES, WHICH IF NOT

FOLLOWED, COULD RESULT IN SERIOUS DAMAGE OR FAILURE OF

THE EQUIPMENT.

www.bindicator.com

I. HANDLING AND STORAGE

SAVE THESE INSTRUCTIONS

INSPECTION AND HANDLING

Do not dispose of the carton or packing materials.

Each package should be inspected upon receipt for damage that may have occurred due to mishandling

during shipping. If the unit is received damaged, notify the carrier or the factory for instructions. Failure to

do so may void your warranty. If you have any problems or questions, consult the manufacturer Customer

Support at 1-800-778-9242.

DISPOSAL AND RECYCLING

This product can be recycled by specialized companies and must not be disposed of in a municipal collection

site. If you do not have the means to dispose of properly, please contact the manufacturer for return and

disposal instructions or options.

STORAGE

If the product is not scheduled for immediate installation following delivery, the following steps should be

observed:

1. Following inspection, repackage the unit into its original packaging.

2. Select a clean dry site, free of vibration, shock and impact hazards.

3. If storage will be extended longer than 30 days, the unit must be stored at temperatures between -31

to 140° F (-35 to 60° C) in non-condensing atmosphere with humidity less than 98%.

CAUTION: DO NOT STORE A NONPOWERED UNIT OUTDOORS FOR A PROLONGED PERIOD.

Pulse Point™ LP-500ST

Installation & Operation Manual

www.bindicator.com

II. GENERAL SAFETY

AUTHORIZED PERSONNEL

All instructions described in the document must be performed by authorized and qualied service personnel

only. Before installing the unit, please read these instructions and familiarize yourself with the requirements and

functions of the device. The required personal protective equipment must always be worn when servicing this

device.

USE

The device is solely intended for use as described in this manual. Reliable operation is ensured only if the

instrument is used according to the specications described in this document. For safety and warranty reasons,

use of accessory equipment not recommended by the manufacturer or modication of this device is explicitly

forbidden. All servicing of this equipment must be performed by qualied service personnel only. This device

should be mounted in locations where it will not be subject to tampering by unauthorized personnel.

MISUSE

Improper use or installation of this device may cause the following:

• Personal injury or harm

• Application specic hazards such as vessel overll

• Damage to the device or system

If any questions or problems arise during installation of this equipment, please contact the manufacturer

Customer Support at 800-778-9242.

www.bindicator.com

III. PRODUCT DESCRIPTION

FUNCTION

The LP-500ST is a vibrating rod, level measuring switch suitable for low and high level indication of granules and

powders with a minimum density of 3.12 lbs/ft3(0.05 kg/dm3density), using vibratory technology.

APPLICATIONS

Unlike radio frequency and capacitance technology sensors, the LP-500ST vibrating probe senses material using

a mechanical principle and is therefore not aected by the dielectric constant of the material. This makes it an

ideal sensor in plastics, dust, shavings, cement, lime, sand, grain, feed, sugar, etc.

FEATURES

• Universal power supply: AC or DC

• No calibration required

• Adjustable sensitivity

• Fine polished probe

TECHNICAL SPECIFICATIONS

FUNCTIONAL

Power Requirements 20 to 255 V AC/DC

Power Consumption ≤ 2.5 VA/2 W

Temperature See Figure 1

Outputs Main Relay: 8A SPDT @ 250 VAC, AC1

PERFORMANCE

Pressure Rating 362 psi (25 bar); cable extended 87 psi (6 bar)

Time Delay Field adjustable; 2 or 5 seconds

Fail Safe Field selectable, high/low level

Sensitivity 3.12 lbs/ft3(0.05 kg/dm3)

Maximum Particle Size 10mm

PHYSICAL

Enclosure Material, Rating Powder Coated Aluminum , IP67, NEMA 6

Conduit Entry

(2)

1/2”NPT;

(2) M20 x 1.5

Process Connections 11/2”NPT

Maximum Insertion Length (std unit) 8.15 in. (207 mm)

Shipping Weight (standard unit) 4.14 lb (1.88 kg)

www.bindicator.com

Figure 1: Temperature Table

Figure 2: Temperature Graph : Ambient Temperature Ta versus Medium Temperature Tm

TEMPERATURE DATA STANDARD AND PIPE EXTENDED VERSION CABLE EXTENDED VERSION

HIGH TEMP

Medium Temperature

Min -22º F (-30º C)

140º F

(60º C)

158º F

(70º C)

203º F

(95º C)

230

º F

(110º C)

320º F

(160º C)

140º F

(60º C)

158º F

(70º C

203º F

(95º C)

Ambient Temperature Range

Min -22º F (-30º C) 140º F

(60º C)

122º F

(50º C)

140º F

(60º C)

122

º F

(50º C)

95º F

(35º C)

140º F

(60º C)

122º F

(50º C)

140º F

(60º C)

Max. Surface Temperature

of Process Connection 185º F

(85º C)

185º F

(85º C)

203º F

(95º C)

203

º F

(95º C)

275º F

(135º C)

185º F

(85º C)

185º F

(85º C)

203º F

(95º C)

Max. Surface Temperature 185º F

(85º C)

185º F

(85º C)

203º F

(95º C)

230

º F

(110º C)

320º F

(160º C)

185º F

(85º C)

185º F

(85º C)

203º F

(95º C)

www.bindicator.com

IV. MECHANICAL INSTALLATION

GUIDELINES

The following precautions should be observed when installing and operating the product:

• The installation and wiring of this product must comply with all national, federal, state, municipal and

local codes that apply.

• This product is a precision device - handle the device with great care, especially the sensing probe.

• Any impact on the sensing probe may ruin its resonance system.

• A protective shield should be installed if the probe is exposed to falling material or excessive mechanical

load.

MOUNTING CONSIDERATIONS

Prior to installation, it is advised to check the switching function for proper adjustment on a sample quantity of

material. The unit may not work with mediums within the specied density range but having very large size of

granules or extremely little friction.

Screw in the device by its hexagon neck. After screwing tight the process connection, the housing can be

rotated (max. 300°), to adjust the cable gland to the required position. It might be necessary to install the device

at an oset level position relative to the switching level actually required taking into account angle of repose of

the material in the silo, see Figure 3.

Figure 3: High/Low Level Location

High Level Location Low Level Location

WARNING: REMOVE POWER FROM THE UNIT BEFORE INSTALLING, REMOVING, OR MAKING

ADJUSTMENTS

CAUTION: ATTEMPTING TO TIGHTEN THE LP500ST BY ROTATING THE HOUSING OR ROD

MAY DAMAGE THE UNIT AND VOID THE WARRANTY.

www.bindicator.com

Figure 4: Mounting Position

With powder level detection, device should be installed at an inclination exceeding the angle of repose (or, in

case of high level detection vertically), to prevent powder deposition on vibrating rod that might substantially

reduce the self-cleaning eect. Also avoid mounting the rod in a recess, see Figure 4.

In case of tanks that are likely to be exposed to intense vibrations, necessary provisions shall be made by the customer for

damping the vibrations acting on the device (e.g. vibration damping inserts made of rubber have to be applied).

Tabla de contenidos

Otros manuales de Instrumento de medición de Bindicator

Bindicator

Bindicator PRD1000 Manual de usuario

Bindicator

Bindicator MP Series Manual de usuario

Bindicator

Bindicator SonoTracker Ultrasonic Liquid Level Manual de usuario

Bindicator

Bindicator Pulse Point II Series Manual de usuario

Bindicator

Bindicator Roto-Bin-Dicator Manual de usuario

Bindicator

Bindicator VRF-2000R Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario