Billion SG6300NZL Manual de usuario
www.billion.com.tw
www.smartgrid.com.tw
SG6300NZL Quick Start Guide
www.billion.com.tw
www.smartgrid.com.tw
Chapter 1: SG6300NZL Hardware Installation
1.1 SG6300NZL Overview
1.2 Internet Installation
1.3 ZigBee Pairing
1.4 RS485 Installation
Chapter 2: Network Configuration
2.1 Configuring a PC in Windows 7
Chapter 3: Factory Default Settings
Chapter 4: Information from your ISP
Chapter 5: Configuring internet with your Web Browser
5.1 Internet connection configuration by Quick Start
Chapter 6: Energy Management with ZigBee device
6.1 ZigBee Configuration
6.2 ZigBee Device Monitor
Chapter 7: Energy Management with RS485 device
7.1 RS485 Configuration
7.1 RS485 Device Monitor
www.billion.com.tw
www.smartgrid.com.tw
Chapter 1: SG6300NZL Hardware Installation
1.1 SG6300NZL Overview
SG6300NZL Front Panel LEDs
1 Power Green: Power ON
Red: System failure. Restart the device or contact
2 LAN
Lit up:
Successfully connected with a broadband connection device
Blinking:
Data being transmitted/received
3 WAN
Lit up:
Successfully connected with a broadband connection device
Blinking:
Data being transmitted/received
4 USB Green:
Connecting to a USB dongle or a hard drive.
5 Wi-Fi
Lit up:
Successfully connected with a broadband connection device
Blinking:
Data being transmitted/received
6 ZigBee
Flashes about once every 3 seconds when the wireless
connection is established.
Flashes about 3 times per second when the device is set to the
state waiting for being joined by other smart meters.
7 RS485 Green:
Build up the connection between Gateway and RS485 device
8 WWAN
4G LTE status
Green: Excellent signal condition
Green flashing quickly: Good signal condition
Orange flash quickly: Fair signal condition
Orange flash slowly: Poor signal condition
Orange: No signal
www.billion.com.tw
www.smartgrid.com.tw
Off: No LTE module
9 Internet Green: Connect to internet
Orange: Disconnect to internet
SG6300NZL Rear Panel
1 RS485 Connect to RS485 device
2 SD Card Data storage
3 USB Data storage
4 WAN WAN 10/100M Ethernet port (with auto crossover support);
connect Cable modem here.
5 LAN
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the
LAN ports when connecting to a PC or an office/home network
of 10Mbps or 100Mbps.
6 ZigBee Push ZigBee button to trigger ZigBee function, thus smart
meter allowing join in is starting
7 Reset
To be sure the device is being turned on press RESET button for
6 seconds and above: restore to factory default settings.
(Cannot
login to the router or forgot your Username/Password. Press
the button for more than 6 seconds).
Caution: After pressing the RESET button for more than
6 seconds, to be sure you power cycle the device again.
8 Power Connect it with the supplied power adapter.
9 Switch Device is power on/off.
www.billion.com.tw
www.smartgrid.com.tw
1.2 Internet Installation
EWAN Installation
SG6300NZL’s WAN port connects to backbone router’s LAN port.
Please refer 5.1 Internet connection configuration by Quick Start to set internet.
4G LTE Installation
Insert the SIM card with the gold contact facing down.
Please refer 5.1 Internet connection configuration by Quick Start to set internet.
www.billion.com.tw
www.smartgrid.com.tw
1.3 ZigBee Pairing
Example SG3015 serials pair to SG6300NZL
STEP_1 Ensure the ZigBee device power on and not join any ZigBee coordinator.
If Status LED lit green that mean ZigBee Meter is waiting mode, please go STEP 3
If Status LED blinking green that mean ZigBee Meter has been pair other SG6300NZL,
Before pair ZigBee Meter with SG6300NZL, please refer ZigBee Meter UM to do
un-pairing.
STEP_2 Push ZigBee button on the rear panel of the ZigBee Coordinator to make a connection.
STEP_3 Then, ZigBee LED in the front panel will blink quickly around 60 seconds
STEP_4 The smart meter will be automatically paired and joined to the ZigBee network.
The Meter Status LED would blink slowly and steadily, indicating that the power meter is
successfully paired
STEP_5 Access to SG6300NZL’s WEB GUI to configure your ZigBee Device
Please refer 6.1 ZigBee Configuration
www.billion.com.tw
www.smartgrid.com.tw
1.4 RS485 Installation
Example SG3010S serials connect to SG6300NZL by RS485
STEP_1 Install SG3010S in the real side, ensure meter power ON.
STEP_2 SG3010S’s RS485+ connect to SG6300NZL’s RS485+
SG3010S’s RS485- connect to SG6300NZL’s RS485-
STEP_3 Access to SG6300NZL’s WEB GUI to configure your ZigBee Device
Please refer 7.1 RS485 Configuration
www.billion.com.tw
www.smartgrid.com.tw
Chapter 2: Network Configuration
2.1Configuring a PC in Windows 7
1. Go to Start. Click on
Control Panel.
2. Then click on Network and
Internet.
3. When the Network and
Sharing Center window
pops up, select and click on
Change adapter settings
on the left window panel.
4. Select the Local Area
Connection, and right click
the icon to select
Properties.
www.billion.com.tw
www.smartgrid.com.tw
5. Select Internet Protocol
Version 4 (TCP/IPv4) then
click Properties.
6. In the TCP/IPv4 properties
window, select the Obtain
an IP address
automatically and Obtain
DNS Server address
automatically radio
buttons. Then click OK to
exit the setting.
7. Click OK again in the Local
Area Connection
Properties window to apply
the new configuration.
www.billion.com.tw
www.smartgrid.com.tw
Chapter 3: Factory Default Settings
Before configuring the Billion SG6300NZL router, you need to know the following default
settings.
Web Interface: (Username and Password)
Username: admin
Password: admin
The default username and password are “admin” and “admin” respectively.
Device LAN IP settings
IP Address: 192.168.5.254
Subnet Mask: 255.255.255.0
ISP setting in WAN site
Obtain an IP Address Automatically
DHCP server
DHCP server is enabled.
Start IP Address: 192.168.5.100
IP pool counts: 100
LAN and WAN Port Addresses
The parameters of LAN and WAN ports are preset at the factory. The default values are
shown below
LAN Port WAN Port
IP address 192.168.5.254 The DHCP function is
enabled to automatically get
the WAN port configuration
from the ISP.
Subnet Mask 255.255.255.0
DHCP server function Enabled in LAN port
IP addresses for
distribution to PCs
100 IP addresses continuing
from 192.168.5.100 through
192.168.5.199
Tabla de contenidos
Otros manuales de Puerta de Billion
Billion
Billion Bipac 9800 VNX Manual de usuario
Billion
Billion BiGuard 2 Manual de usuario
Billion
Billion BiGuard 50G Manual de usuario
Billion
Billion BiGuard 10 Manual de usuario
Billion
Billion BiGuard S3000 Manual de usuario
Billion
Billion BiGuard 30 Manual de usuario
Billion
Billion BiGuard 50G Manual de usuario
Billion
Billion BiGuard 50G Manual de usuario
Billion
Billion BiGuard 30 Manual de usuario
Billion
Billion BiGuard 2 Manual de usuario
Billion
Billion BiGuard S100N Manual de usuario
Billion
Billion BiGuard 50G Manual de instalación y operación
Billion
Billion BiGuard S100N Manual de usuario
Billion
Billion BiGuard S10 Manual de instrucciones
Billion
Billion BiGuard S10 Manual de usuario
Billion
Billion BiGuard S5 Manual de usuario
Billion
Billion BiGuard 2 Manual de usuario
Billion
Billion BiGuard 10 Manual de usuario
Billion
Billion BiGuard S10 Manual de usuario
Billion
Billion SG6200NXL Manual de usuario
Manuales populares de Puerta de otras marcas
LST
LST M500RFE-AS Manual de usuario
Kinnex
Kinnex Media Gateway Manual de usuario
2N Telekomunikace
2N Telekomunikace 2N StarGate Manual de usuario
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario
Telsey
Telsey CPVA 500 - SIP Manual de usuario
