BigSAT BS-S 67CR-M Manual de usuario

SAFETY PRECAUTION

CAUTION:

The lightning flash with

arrowhead symbol, within

an equilateral triangle, is

intended to alert the user

to "dangerous voltage"

and to prevent from a risk

of electric shock.

Warning:

To reduce the risk of

electric shock, don't open

the cabinet. Refer

servicing to qualified

personnel only.

The exclamation point

within an equilateral

triangle is intended to alert

the user to important

operating and

maintenance (servicing).

WARNING: Do not use this STB where contact with or immersion in water is a possibility. Do

not use near flower vase, washbowls, kitchen sinks, laundry tubs, swimming pools, etc.

WARNING: Do not put the candle or lamp stand on the cabinet; otherwise, there is the danger

of fire.

WARNING: The unit should be connected to a power supply only of the type described in the

operating instructions or as marked on the unit. If you are not sure of the type of power supply

(for example, 120 or

230 V) to your home, consult your local dealer or local power company.

WARNING: This product install diodes. Do not open the cabinet or touch any parts in the inner

mechanism. Consult your local dealer for technical service if the opening is required.

Note: To ensure proper use of this product, please read this User manual carefully and

retain for further reference.

Note: This product install diodes. Do not open the cabinet to avoid the unit direct exposure to

radiation.

Unit Cleaning: After the unit power is turned off, you can clean the cabinet, panel and remote

control with a soft cloth lightly moistened with a mild detergent solution.

Attachments: Never add any attachments and/or equipment without the manufacturer

consent; as such additions may result in the risk of fire, electric shock, or other personal injury.

Locating: Slots and openings in the cabinet are provided for ventilation to protect it from

overheating. Do not block these openings or allow them to be blocked by placing the STB on a

bed, sofa, or other similar surface, nor should it be placed over a radiator or heat register.

Power-Cord Protection: Place the power-supply cord out of the way, where it will not be

walked on. Please take special attentions to cords at plugs, convenience receptacles, and the

point where they exit from the unit.

Object and Liquid Entry: Never put objects of any kind into this STB through openings, as

they may touch dangerous voltage points or short-out parts that could result in a fire or electric

shock. Never spill any liquid on the STB.

Note: Moisture may be formed on the lens In the following conditions:

when the unit is suddenly moved from a cold environment or an air-condition room to a

warm place.

immediately after a heater has been turned on.

in a steamy or very humid room.

If the moisture forms inside the unit, it may not operate properly. To correct this problem, turn

on the power and wait about two hours for the moisture to evaporate.

Parts Replacement: When the unit parts need to be replaced, user should make sure the

service technician use the replacement parts specified by the manufacturer or having the

same characteristics as the original part. Unauthorized replacement may put the unit In the

risk of fire, electric shock or other hazards.

Safety Check: After all the maintenances and repairs are done, user is required to request the

service technician to conduct the overall safety check to ensure the machine is In the proper

condition.

Basic Operations

CONTENTS

REMOTE CONTROL.......................................................................................................4

FRONT PANEL...............................................................................................................5

REAR PANEL .................................................................................................................5

CONNECTING YOUR SYSTEM......................................................................................6

CHANNEL.......................................................................................................................7

5.1

HANNEL

ANAGER

...............................................................................................................7

5.1.1

Group .........................................................................................................................................................................7

5.1.2

Skip.............................................................................................................................................................................8

5.1.3

Edit.............................................................................................................................................................................8

5.1.4

Sort.............................................................................................................................................................................9

5.1.5

Favorite......................................................................................................................................................................9

5.1.6

Find..........................................................................................................................................................................10

5.2

ADIO

HANNEL

IST

..................................................................................................................10

5.3

ELETE

.................................................................................................................................10

INSTALLATION ............................................................................................................11

6.1

NSTALLATION

.............................................................................................................................11

6.2

ETTING

.................................................................................................................................13

SYSTEM SETUP...........................................................................................................13

7.1

ANGUAGE

...................................................................................................................................14

7.2

YSTEM

..................................................................................................................................14

7.3

OCAL

IME

ETTING

..................................................................................................................15

7.4

IMER

...........................................................................................................................................15

7.5

TARTUP

HANNEL

......................................................................................................................16

7.6

HANNEL

LAY TYPE

...................................................................................................................17

7.7

OSD

ETTING

...............................................................................................................................17

7.8

ARENTAL

OCK

..........................................................................................................................18

TOOLS..........................................................................................................................19

8.1

NFORMATION

..............................................................................................................................19

8.2

ATELLITE

UIDE

........................................................................................................................19

8.3

EFAULT

ALUE

..........................................................................................................................20

8.4

OFTWARE

PGRADE

...................................................................................................................20

GAME............................................................................................................................22

9.1

ETRIS

..........................................................................................................................................22

9.2

NAKE

..........................................................................................................................................22

9.3

THELLO

......................................................................................................................................22

10.

TROUBLE SHOOTING .................................................................................................23

11.

SPECIFICATIONS.........................................................................................................24

11.1

ENERAL

......................................................................................................................................24

11.2

A/V

ODE

...................................................................................................................................24

11.3

ICROPROCESSOR

EMORIES

.................................................................................................24

11.4

OWER

NVIRONMENT

ONDITION

.........................................................................................24

11.5

HYSICAL

PECIFICATION

............................................................................................................24

11.6

ONNECTION

................................................................................................................................24

Basic Operations

1. Remote Control

You can power on/off the receiver, operate on screen menu, and use a variety of hot key function.

POWER

To switch your receiver on from standby or standby to on.

MUTE

Used to enable or disable the audio

Displays the Main Menu on the screen, or return to the previous menu

or status

(PREVIOUS

)

Return to the previous menu or status.

SAT

Display satellite list.

EXIT

Cancel the user selection and return to the viewing mode from a menu.

(

((

(

TV / RADIO)

Receiver switches between TV and Radio mode.

(INFORMATION)

To display channel status or various program information of current

service.

NUMERIC KEYS

Used to select channels or enter programming parameters

To select menu option, or to updated on entry.

PAUSE

Used to select the freeze function.

Press once to freeze the screen picture.

Press again to go to normal state.

<,> KEY

To adjust volume level, or to move cursor left or right in the menu

^,v KEY

To change channels, or to move cursor up or down in the menu

UHF

In case your TV is connected through RF Modulator (UHF), select

output channel number between CH21 and CH69 with up and down

key.

FAV(FAVORITE)

To set receiver to the favorite server mode,

display the favorite channel

AUDIO

To select audio mode; Left, Right, Stereo

P+/P-

To move up the cursor to the next or previous page

in the menu or channel list

TV/SAT

Receiver switches between TV and Satellite receive mode.

(ZOOM)

Press key select zoom times, from X1 to X16.

(WHITE KEY)

Subtitle Display.

TIMER(YELLOW KEY)

Press timer key then enter timer menu. You can setup up total 8 tasks.

(RED KEY)

Audio channels setup, to select audio mode; Left, Right , Stereo.

(GREEN KEY)

Multi channels display. You can choice the desire channel use <,> ^,v

and press ok confirm.

TELETEXT(BLUE KEY)

Shows teletext information of the current channel supports.

(FIND)

Use to prompt find channels sort by character.

Basic Operations

2. Front panel

POWER: To switch the receiver power on/stand by

VOL^, v KEY: To adjust volume level, or to move cursor left or right in the menu

CH ^, v KEY : To change channels, or to move cursor up or down in the menu

Remote Sensor: Detects infrared signal from remote control unit

Display(4-Digit/7-Segment): Indicates operating status of receiver

Power Led: Lights up while the receiver is power on

Signal Led: When receiving signal is strong, the signal led is lighted.

MENU KEY: To enter into the main menu

OK KEY: To see TV/Radio channel list, or to confirm in the menu

3. Rear Panel

Please refer to the diagram above for all possible connections of your receiver

Do not connect the unit to the mains socket until all other connections have been made and

checked.

LOOP: This enables the connection of another receiver.

13/18V 500mA MAX LNB IN: This port is to connect the coaxial cable from LNB of your Dish.

ANT IN: Connect to Analog TV antenna.

TV OUT : This is used to connect your TV through RF cable.

VIDEO : This RCA connector is used to connect any external video.

0-12V :This is used to Connect 12V to an external 0V/12V switch.

AUDIO R/L : These RCA connectors are used to connect any external audio amp or system.

RS 232C SERIAL PORT: This is used to connect your receiver to a computer through a serial

cable.

TV : This is used to connect your TV through SCART cable.

Basic Operations

4. Connecting Your System

There are three ways to connect the receiver to your existing TV system. We recommend using one

of the following cases for the best result :

1. Connect one end of SCART cable to the TV(SCART) jack on the back of the receiver and the

other end to a SCART jack on your TV.

2. Connect one end of RCA cable to the RCA jack on the back of the receiver and the other end to a

RCA jack on your TV.

3. If your TV doesn't have a RCA jack, connect one end of RF cable to the TV on the back of the

receiver and the other end to a RF input jack on your TV.

Finally connect the coaxial cable from the LNB to the LNB IN jack on the receiver.

_ With External Audio / Hi-Fi System

To connect any external Audio Hi-Fi system, the receiver has been provided with two RCA

connectors

at the back of the receiver marked with Audio L and R.

Connect an RCA stereo cable from the AUDIO L, R jacks on the back of the receiver to the LINE,

AUX, SPARE OR EXTRA input jacks on your Hi-Fi System.

4.1 TV with Motorized System (DiSEqC 1.2)

Connect one end of your coaxial cable to the LNB IN connector on the receiver and the other end to

the REC or Receiver connector on the DiSEqC 1.2 motor.

Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1.2 motor.

All our receivers are designed to be DiSEqC 1.0 and DiSEqC 1.2 compatible.

This allows multiple antennas to be connected to the receiver at the same time.

If you have two or more fixed antennas or LNBs, then we recommend you use a DiSEqC 1.0

switch.

Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC

switch.

Do the same for any other LNBs that you have.

Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch,

connect the other end to the LNB IN socket on the receiver.

To the digital receiver, you can connect either a single satellite antenna directly or LNB of

multi-feed equipment.

Menu Operations

5. Channel

When you press[Menu]key to enter menu,

there will display the picture like below:

Press[Up/Down]key to select menu pages

among Channel, Installation, System and

Tools.

Press[OK]key to enter the selected item.

In “Channel” menu:

Press[Channel Up/Channel Down]key to

select menu items among TV Channel, Radio

Channel and Delete All.

Press[OK]key to enter the selected item.

5.1 TV Channel Manager

When you enter to “Channel List” menu, there

will display the screen like below.

You can move highlight by press[Channel

Up/Channel Down]key and press[OK]key to

preview the current highlighted program in the

right side preview window.

You can press[Page Up/Page Down]key to

implement the Page Up/Page Down function.

You can use Red button to switch “Program

Group”.

You can press[Menu]or[Exit]keys to enter full

screen playing mode.

Press color key can implement the

corresponding function in “Channel Manager”.

5.1.1 Group

Press [Red] key can open the “Group” window

like above

You can press [Up/Dwon] key to move

highlight and press [OK] key to select group.

Press [Red] key or [Menu] key to close

“Group” list.

Menu Operations

5.1.2 Skip

In “TV Channel Manager” menu, press

[Green] key can make a “skip mark” in the

right side of the highlighted channel.

After save and exit “TV Channel Manager”

menu, the channel will be skip while user

change channel in the full screen.

5.1.3 Edit

Press [Yellow] key, it will show input password

dialog. If the password is correct, it will open the

window like below. The default password is

0000.

5.1.3.1 Delete

In this menu, press [Red] key can make a

delete mark in the right side of the highlighted

channel.

Press [Red] key again can cancel the deleted

mark on the current channel.

When exit the menu, it will ask you whether to

save the change. Select “Yes” to save the

change.

5.1.3.2 Create

If you press[Green] key, it will display create

window like below:

In “Satellite” item, press[OK] key can

display satellite list and you can select a

satellite that you want to setting.

In “TP Index” item, you can press[Volume

Up/Volume Down]key can switch TP

number, and the next three items will show

up corresponding parameters.

In “Name” item, press[OK]key can display

the keypad, and you can edit new name

here for selected channel.

In “Video PID”, “Audio PID” and “PCR PID”

items, you can use the number key directly

to modify corresponding parameters of the

items.

After modification, move highlight to “Save”

item and press[OK]key, can save

parameter and exit “Edit” mode. Otherwise,

move highlight to [Exit]item and

press[OK]key can exit “Edit” mode and

won’t save any modification.

5.1.3.3 Edit

If you press[Yellow] key, it will show the window

like below:

Menu Operations

1 On the “Name” item, press[OK]key can

display keypad to edit the name of selected

channel.

2 On the “Video PID”, “Audio PID” and “PCR

PID” items, you can input numerals to

modify the according item’s value.

3 After modification, move highlight to “Save”

item and press[OK]key can save the

modified value and exit “Edit” mode.

Otherwise, move highlight to [Exit]item and

press[OK]key can exit “Edit” mode and

won’t save any modification.

5.1.3.4 Lock

Press [Blue] key can make a “lock mark” in

the right side of the highlighted channel.

After save and exit the menu, STB will

request you to input the password while you

want to watch the locked channel.

5.1.3.5 Move

In this menu, press [White] key can make a

moving mark in the right side of the

highlighted channel.

Press [Up/Down] key to move the channel

Press [OK] key to put the channel to the

target place.

When exit the menu, it will ask you whether

to save the change. Select “Yes” to save

the change.

5.1.4 Sort

Press [Blue] key can open the “Sort”

window like above. There are five kinds of

sorting ways. You can press[Channel

Up/Channel Down]key to move highlight

and press[OK]key to confirm you selection

The five kinds of sorting way are:

Default: Sorting by scanning result.

Name (A-Z): Sorting in Alphabetical

Order, ignore “$” symbol.

Name (Z-A): Sorting in Alphabetical

Order, ignore “$” symbol.

FTA: Sort channel by free and scramble

sequence. Free channel will at front of

channel list and scramble channel will at

reat of channel list

Lock: Accumulated all locked channels

and list in the last of TV Channel List.

5.1.5 Favorite

Menu Operations

1 Press [White]key can open the “Favorite”

window like above

2 You can move highlight between 8 favorite

groups by press[Channel Up/Channel

Down]key and press[OK]key to make a

favorite mark in the right side of the

selected Favorite group.

3 Press[OK]key on the marked Favorite

group can cancel the exist favorite mark.

4 After marking, press[Exit]key can back to

“TV Channel List” , there will show a

favorite mark beside the marked channel.

5.1.6 Find

Press[Find] key can open the “Find”

window like above. You can press[Channel

Up/Channel Down/Volume Up/Volume

Down]key to move highlight and

press[OK]key to input the selected symbol

or letter into the dialogue.

After input each character, the program list

on the left will search the channel

according your input, and list the matched

channel.

Press[Exit]key can close “Find” window

and you can select channel from the

channels list directly.

5.2 Radio Channel List

Basically, the operation of “Radio Channel

Manager” is same as “TV Channel Manager”,

but there is one point different: In “Radio

Channel Manager” mode, there is no video

information, so it will always display Radio’s

logo in the right side preview window.

5.3 Delete All

In “Delete All” item:

There will display an dialogue for user to

key in password. The default Password is

“0000”.

When you input the correct password, there

will show up a warning message box to

inquire you whether delete all or not.

If you select “Yes”, all channels will be

deleted.

In step 1 and step 2, press[Exit]key can exit

the function directly without save.

?Frequently Asked Question

Q: IF I incautiously delete all channels,

what should I do?

A: there are two ways to restore:

To re-search all channels in “Installation”

function.

Use “Default Value” function to restore all

channels in “Tools” function.

Tabla de contenidos

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario