Biamp TesiraFORTE Manual de usuario
TesiraFORTÉ Fan Replacement
This article will walk you through the process to replace the fan inside of a TesiraFORTÉ unit. Please read this
document carefully in its entirety before beginning as there are delicate components inside the TesiraFORTÉ.
Locate the fan
The fan is located at the front of the Chassis for the TesiraFORTÉ, on the left side of the unit if you are looking straight
on at the device. Make sure that all cables are disconnected from the unit before you remove the Chassis from the rack,
and verify that the device has been powered down.
Open the chassis
Using a Phillips-head screwdriver, remove the three screws shown below from the back of the TesiraFORTÉ chassis.
Lift off the top plate to remove it and set aside.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 1
Remove the front panel
Before you remove the front panel, make note of the 2 ribbon cables on the TesiraFORTÉ. Take extra care to avoid
damaging these two cables. If they are damaged, the front panel LED screen may no longer function.
Unplug the white ribbing cable, grip gently and pull straight out of the connector.
Unclasp the front panel brackets and gently slide the front panel forward. Exercise caution to avoid damaging either
ribbon cable. Once the front panel is removed, rest it face side down to reduce the change of damaging the cables.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 2
Remove the fan
Now that the fan is exposed, remove the screws holding the fan housing in place. Note that the fan is attached to the
main board on the TesiraFORTÉ as well. Disconnect this carefully to avoid damaging the connector on the board.
Remove the screws from the front panel that hold the fan housing in place.
Push firmly at the bottom of the fan and will slide out under the metal lip of the chassis. Ensure that you press on the
bottom of the fan housing and not the fan itself.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 3
Remove the fan from its housing by removing the two retainer screws.
Install the new fan
Attach the new fan to the housing using the same screws removed in the previous step.
Insert the fan assembly back into the TesiraFORTÉ by hooking the fan underneath the lip of the TesiraFORTÉ frame
and push inward on the bottom of the assembly to move it into place. This will require firm pressure but not enough to
damage any components.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 4
Replace the front panel
Take note of the two holes in the front plate. These line up with the two ribbon cables attached to the front
panel assembly.
Line up the front panel with the plate and press it back into place until the front panel latches are engaged. Use caution
to avoid damage to the ribbon cables. If they are bent excessively or pinched, the front panel will likely no longer
function.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 5
Reconnect the white ribbon cable to its receiving connector located on the main circuit board. Press straight down and
take care to not bend the cable to the point of damage. The amount of pressure needed should be firm and steady, but
not excessive to where it will damage the cable.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 6
Otros manuales para TesiraFORTE
2
Tabla de contenidos
Otros manuales de Hardware de computadora de Biamp
Biamp
Biamp Nexia Series Manual de usuario
Biamp
Biamp ADVANTAGE NMP200 Manual de uso y mantenimiento
Biamp
Biamp Tesira SERVER Manual de usuario
Biamp
Biamp MSP11 Manual de usuario
Biamp
Biamp Devio SCX Manual de usuario
Biamp
Biamp ADVANTAGE NMP200 Manual de usuario
Biamp
Biamp VOCIA VI-6 Manual de usuario
Biamp
Biamp QtPro Series Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
.jpg?revision=1){kind=link}