BGS technic 8216 Manual de usuario

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

Art. 8216

Engine Timing Tool Set VW 2,4 & 2,5 Diesel

GENERAL

This timing tool set enables checking and adjusting of the engine timing and is suitable for VW models

Transporter 2.4D (95-03), Crafter 2.5TDI (06-09) and LT models with engine codes AAB, AJA, BJJ,

BJK, BJL, BJM.

SAFETY ADVICE

xDO NOT use the set if any parts are missing or damaged.

xNever lay tools on the vehicle's battery. This may short the terminals together.

xBe careful when working on running engines. Loose clothes, tools and other things can be caught

up in revolving parts which may lead to serious injuries.

xKeep children and other unauthorised persons away from the working area.

xBe careful when working on hot engines – risk of burn!

xRemove the ignition key before repair so that the engine will not start unintentionally.

xThis manual is just brief information and will not replace a garage handbook.

xAlways consult specific service literature for information about torques, assemblies and

disassemblies etc.

xAfter any successful maintenance and before starting the engine, you should rotate the engine for

two turns manually to check the new control time.

xDo not use cleaning fluids on belts, sprockets or rollers

xTurn the engine in the normal direction (clockwise unless stated otherwise)

TOOLS

Crankshaft Counterholder

to be used as

OEM T10025

Pump Locking Tool

to be used as

OEM 2064

Crankshaft Adjusting Tool

to be used as

OEM 2065A

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

INSTRUCTIONS

Use this tool to hold the Crankshaft Pulley Flange during

loosening the pulley flange centre bolt.

Note: Do not release the pulley flange centre bolt during the

camshaft and crankshaft timing tools are in place.

Always use the counterholder during loosen the centre bolt.

Use this tool to adjust the injector pump wheel.

A fine adjustment of the injection pump must be made, where

appropriate, by turning the pump.

The tool is used to adjust the camshafts.

Turn the camshaft until one side of the tool on the sealing

surface rests.

Measure the clearance between the tool and the sealing

surface with the feeler gauge on the opposite side.

Aligning the camshaft so that feeler gauge fits with half

clearance on both sides between ruler and sealing surface.

Tabla de contenidos

Otros manuales de Herramientas de BGS technic

BGS technic

BGS technic 1898 Manual de usuario

BGS technic

BGS technic 3294 Manual de usuario

BGS technic

BGS technic 9246 Manual de usuario

BGS technic

BGS technic 8849 Manual de usuario

BGS technic

BGS technic 1773 Manual de usuario

BGS technic

BGS technic 6932 Manual de usuario

BGS technic

BGS technic 1230 Manual de usuario

BGS technic

BGS technic BGS 9086 Manual de usuario

BGS technic

BGS technic 1833 Manual de usuario

BGS technic

BGS technic 9088 Manual de usuario

BGS technic

BGS technic 9387 Manual de usuario

BGS technic

BGS technic 9324 Manual de usuario

BGS technic

BGS technic 70345 Manual de usuario

BGS technic

BGS technic 70112 Manual de usuario

BGS technic

BGS technic 74386 Manual de usuario

BGS technic

BGS technic 67307 Manual de usuario

BGS technic

BGS technic 62625 Manual de usuario

BGS technic

BGS technic 9858 Manual de usuario

BGS technic

BGS technic 3201 Manual de usuario

BGS technic

BGS technic 9015 Manual de usuario

BGS technic

BGS technic 9445 Manual de usuario

BGS technic

BGS technic 9992 Manual de usuario

BGS technic

BGS technic 62622 Manual de usuario

BGS technic

BGS technic 70009 Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar

Goobay

Goobay 97790 Manual de usuario