BGS technic 6667 Manual de usuario

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

BGS 6667

Clutch Aligning Tool Set for Trucks

TOOLS

1 Centering mandrel (clutch disc), 42 - 52 mm

2 Centering mandrel (clutch disc), 36 - 45 mm

3 Centering sleeve (pilot bearing), 30 mm

4 Centering sleeve (pilot bearing), 27 mm

5 Centering sleeve (pilot bearing), 25 mm

6 Centering sleeve (pilot bearing), 20 mm

7 Replacement O-rings

INTENDED USE

This tool set is required when replacing truck single and double clutch discs and allows a professional

centering of clutch discs.

SAFETY INFORMATIONS

•Read carefully the instructions before working with this tool set.

•Do not use this tool set for other purpose for which it is designed.

•Observe the general safety instructions for garages.

•Keep your work area tidy and clean. Areas or corridors which are untidy increase the risk of injury.

•Lifting of vehicles only allowed on the special lifting points.

•Before starting the work under a vehicle always ensure that it is adequately supported by axle

stands or ramps. Chock wheels and ensure that the hand brake is firmly applied.

•Always use approved eye protection, especially when working under vehicles.

•Ensure a secure and well-gripped stance during fitting.

•Check the condition of the tool regularly and do not use it if it is damaged.

•Make sure the tool is properly mounted.

•This manual serves as a brief guide and does not replace a workshop manual. Always refer to the

vehicle-specific service literature, particularly the technical data such as torque values and

instructions for disassembly/assembly, etc..

•Keep children and other unauthorized persons away from the work area.

•Do not let children play with the tool or its packaging and keep this tool out of the reach of

children.

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

USE

Choose a suitable centring sleeve (3 - 6), it must fit in the

crankshaft bore / pilot bearing.

Choose a suitable centring mandrel (1 / 2) and install the

centring sleeve (3 - 6) onto the thread of the centring mandrel.

Insert the clutch centring mandrel into the clutch hub and fix

the centring mandrel in the clutch hub by turning the knurled

screw clockwise.

Centre the clutch disc with centring sleeve in the crankshaft

bore (pilot bearing) and install the clutch pressure plate.

Attention: Make sure that the clutch disc is mounted in the

proper position.

Loosen the centring mandrel by turning the knurled screw anti-

clockwise and remove it from the clutch hub.

Tabla de contenidos

Otros manuales de Herramientas de BGS technic

BGS technic

BGS technic 8262 Manual de usuario

BGS technic

BGS technic 3274 Manual de usuario

BGS technic

BGS technic 9414 Manual de usuario

BGS technic

BGS technic 1898 Manual de usuario

BGS technic

BGS technic 9584 Manual de usuario

BGS technic

BGS technic 8216 Manual de usuario

BGS technic

BGS technic 8418 Manual de usuario

BGS technic

BGS technic 8156 Manual de usuario

BGS technic

BGS technic 1899 Manual de usuario

BGS technic

BGS technic BGS 9071 Manual de usuario

BGS technic

BGS technic 1514 Manual de usuario

BGS technic

BGS technic 3324 Manual de usuario

BGS technic

BGS technic 6774 Manual de usuario

BGS technic

BGS technic 66202 Manual de usuario

BGS technic

BGS technic 8454 Manual de usuario

BGS technic

BGS technic 9637 Manual de usuario

BGS technic

BGS technic 8776 Manual de usuario

BGS technic

BGS technic B4204 Manual de usuario

BGS technic

BGS technic 6743 Manual de usuario

BGS technic

BGS technic 2832 Manual de usuario

BGS technic

BGS technic 1943 Manual de usuario

BGS technic

BGS technic 8723 Manual de usuario

BGS technic

BGS technic 3140 Manual de usuario

BGS technic

BGS technic 1521 Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar

Goobay

Goobay 97790 Manual de usuario