Bennett H35 Series Manual de usuario

H35 Series Operation Manual

Operation Manual

High Flow H35 Hydrogen Series

Dual Cabinet Configuration

154807 Rev. B, 12.20.2023

H35 Series Operation Manual i

READ THIS MANUAL

Only Trained Personnel May Work on This Equipment

This manual contains important information for the safe operation of this equipment. Read and

understand this manual before applying power. All service personnel should read this manual prior to

performing service activities. The material included in this installation manual is accurate at the date of

publication. Failure to follow these instructions can cause bodily injury, damage to the equipment, or

death.

NOTE:Inspect shipped materials for damage or missing equipment. Bennett Pump Company is not

liable for the hazards of transportation. Please address damage claims directly to the delivery company.

NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

interference received, including interference that may cause undesired operation.

NOTE: Not all equipment covered in this manual is listed by Underwriters Laboratories.

REV LEVEL DATE DESCRIPTION

11/22/2023

Release

B 12/20/2023 Revised Safety Instructions. Revised Error Code Table. 6.3 Safety Device Fault

Response created. Updated all section and figure references.

H35 Series Operation Manual ii

1SAFETY INSTRUCTIONS .......................................1

1.1 SAFETY MESSAGES ...........................................1

2OVERVIEW AND FEATURES.................................3

2.1 EXTERIOR LAYOUT ............................................3

2.2 ELECTRONICS UNIT INTERIOR DOOR LAYOUT.........4

2.3 MANAGER’S KEYPAD.........................................5

2.4 POWER SWITCH ...............................................5

2.5 MAIN DISPLAY REED SWITCHES ..........................6

2.6 ELECTRO-MECHANICAL TOTALIZER -OPTIONAL......7

3HOW TO OPERATE ..............................................8

3.1 DISPENSING FUEL .............................................8

3.2 ERROR MESSAGES ..........................................10

3.3 AC OFF MESSAGE .........................................11

4SETUP AND PROGRAMMING ............................12

4.1 BATTERY DISCONNECT BUTTON ........................13

4.2 DEFAULT SETTINGS .........................................13

4.3 INITIAL SETUP SEQUENCE.................................14

4.4 DISPENSER DISPLAY ........................................15

4.5 MANAGER’S KEYPAD OPERATION......................16

4.6 MANAGER’S ACCESS .......................................17

4.7 SELECT THE DISPENSER DISPLAY TYPE .................17

4.8 MENU CODE 0: DIAGNOSTICS ..........................18

4.9 MENU CODE 1: HOSE TOTALS ..........................18

4.10 MENU CODE 2: TOTALIZER TOTALS ...................19

4.11 MENU CODE 3: MANAGER’S ACCESS .................20

4.12 MENU CODE 4: PRICING..................................21

4.13 MENU CODE 5: TOTALIZER VALUE.....................22

4.14 MENU CODE 6: SPEED PROGRAMMING..............23

4.15 MENU CODE 7: DISPENSER TYPE.......................24

4.16 MENU CODE 8: DECIMAL LOCATION ..................26

4.17 MENU CODE 9: NO FLOW TIMEOUT ..................27

4.18 MENU CODE 11: MASS ALLOCATION.................28

4.19 MENU CODE 12: PRE-CHARGE TIME .................28

4.20 MENU CODE 13: BEEPER.................................30

4.21 MENU CODE 14: PPM DISPLAY OPTIONS ..........31

4.22 MENU CODE 15: FLEET OPTION .......................33

4.23 MENU CODE 16: PUMP HANDLE INPUTS ............34

4.24 MENU CODE 18: MONEY TOTALS .....................35

4.25 MENU CODE 21: COMMUNICATION TYPE...........36

4.26 MENU CODE 22: DISPENSER ADDRESS,PLC, PLC

LOWEST........................................................37

4.27 MENU CODE 26: SHIFT TOTALS ........................40

4.28 MENU CODE 27: ELECTRONIC CALIBRATION........43

4.29 MENU CODE 28: ROUNDING............................45

4.30 MENU CODE 29: RESETTABLE TOTALS ...............46

4.31 MENU CODE 30: REAL TIME CLOCK ..................47

4.32 MENU CODE 49: SOFTWARE REBOOT ................48

4.33 MENU CODE 50: PULSE OUTPUT ......................49

4.34 MENU CODE 51: NOZZLE DRYER CONFIGURATION

AND TIMING..................................................51

4.35 MENU CODE 66: NOZZLE TIME OUT..................52

4.36 MENU CODE 80: NOZZLE DRYER VALVE TEST ......53

4.37 MENU CODE 94: WEIGHTS AND MEASURES

TIMEOUT DELAY.............................................54

4.38 MENU CODE 99: VIEW E-CAL .........................55

5DIAGNOSTICS ................................................... 56

5.1 DIAGNOSTIC CODE 0.......................................56

5.2 DIAGNOSTIC CODE 1: DISPLAY SEGMENT TEST.....58

5.3 DIAGNOSTIC CODE 2: ERROR HISTORY ...............58

5.4 DIAGNOSTIC CODE 3: CPU TEST .......................59

5.5 DIAGNOSTIC CODE 4: FAULT HISTORY ................59

5.6 DIAGNOSTIC CODE 5: PUMP HANDLE TEST .........59

5.7 DIAGNOSTIC CODE 6: NOT USED.......................60

5.8 DIAGNOSTIC CODE 7: PRODUCT SELECT,KEYPAD

TEST ............................................................60

5.9 DIAGNOSTIC CODE 8: LAST SALE LIMIT ...............60

5.10 DIAGNOSTIC CODE 9: NOT USED.......................61

5.11 ERROR CODES................................................62

6APPENDIX ........................................................ 64

6.1 DISPENSER IDENTIFICATION NUMBER (DIN)........64

6.2 PULSE OUTPUT ..............................................65

6.3 SAFETY DEVICE FAULT RESPONSE ......................68

TABLE OF CONTENTS

Safety Instructions

H35 Series Operation Manual Back to TOC 1

1SAFETY INSTRUCTIONS

Please read and understand the following grouped safety messages that contain safety symbols and

safety words. They are defined as:

RED AND WHITE.IF YOU DO NOT FOLLOW THE INSTRUCTIONS, SEVERE INJURY OR DEATH WILL

OCCUR.

Orange and black. If you do not follow the instructions, severe injury or death can occur.

Yellow and Black. If you do not follow the instructions, damage can occur to the dispenser.

White italic NOTICE over blue. Indicates important information that should be observed.

1.1 SAFETY MESSAGES

1. DANGER: HYDROGEN IS FLAMMABLE. NO SMOKING OR OPEN FLAME.

2. DANGER: ALWAYS PLACE A PHYSICAL BARRIER AROUND THE WORK AREA BEFORE

PERFORMING SERVICE OR MAINTENANCE.

3. DANGER: DISCONNECT ALL POWER TO THIS EQUIPMENT DURING INSTALLATION, SERVICE,

OR ANY MAINTENANCE.

1. WARNING: To prevent electric shock, keep the electrical parts of the dispenser dry.

2. WARNING: Electronic components are static sensitive. Use proper static precautions (static

straps) before working on the equipment.

3. WARNING: Only technicians who have been trained in operation and programming of this

dispenser should perform programming and maintenance.

Safety Instructions

H35 Series Operation Manual Back to TOC 2

1. CAUTION: Do not drill holes in fuel dispensers. Holes can cause failure of the electronic

equipment. The warranty will become void. Use only adhesive backed sign mounting

brackets.

Overview and Features

H35 Series Operation Manual Back to TOC 3

2OVERVIEW AND FEATURES

2.1 EXTERIOR LAYOUT

1. Main Display

2. Payment Panel Display (optional)

3. Nozzle Boot

4. Handle Switch

5. Locks (5 places each side each unit).

6. Electro-Mechanical Totalizer (optional)

7. Price Per Mass Displays (PPM) and

Product Select Buttons

Figure 1.1. H35 Dual Layout

Dispenser Unit

Electronics Unit

Overview and Features

H35 Series Operation Manual Back to TOC 4

2.2 ELECTRONICS UNIT INTERIOR DOOR LAYOUT

1. Main Display Board

2. NFC Reader (optional)

3. Payment Card Reader (optional)

4. Keyboard (optional)

5. Payment Panel Display Board (optional)

6. Printer (optional)

7. Price Per Mass Board

Figure 1.2. Interior Door Layout

Overview and Features

H35 Series Operation Manual Back to TOC 5

2.3 MANAGER’S KEYPAD

•The Manager’s Keypad allows users to program and access data, see Figure 1.3.

•Various modes are available to configure and calibrate the dispenser for specific applications.

•The Manager’s Keypad connects to the PPM Circuit Board, refer to Section 4.5 Manager’s Keypad

Operation.

2.4 POWER SWITCH

4. WARNING: To prevent electric shock, make sure the circuit breaker(s) are OFF and locked

and tagged out before doing any repairs or maintenance to the dispenser.

The power switch on the 819 Power

Board turns the dispenser power ON and

OFF, see Figure 1.4. If the Power Board is

switched to OFF, the displays in the

dispenser remain illuminated for 30

seconds with power supplied by the 12-

volt battery.

Figure 1.3. Manager’s Keypad

Figure 1.4. 819 Power Board.

Top arrow - battery disconnect button.

Bottom arrow - ON/OFF switch.

Overview and Features

H35 Series Operation Manual Back to TOC 6

2.5 MAIN DISPLAY REED SWITCHES

The Reed Switches access electronic totals, the last sale, and audit trail

information. They are activated with the Access Magnet provided with the

dispenser, see Figure 1.5.

The reed switch locations are shown on Figure 1.6.

2.5.1 TOTALS SWITCH

To access totals:

1. Hold the Access Magnet over the location on Figure 1.6.

2. After a few seconds, “Prev” will be displayed on the

Price Per Mass (PPM) display.

3. Lift the magnet away.

4. The Main Display will show the previous sale amount

that occurred prior to the transaction that had appeared

on the display while idle.

5. To view the Totals, tap the magnet over the Totals Reed

Switch again. When the first money totals appear,

remove the magnet. The PPM display indicates the first

money total for product.

6. Tap the magnet over the Totals Reed Switch to view all totals from Mode 1 Hose Totals, Mode 2

Totalizer Totals, and Mode 26 Shift Totals.

Figure 1.5. Access Magnet

Battery Recall Reed Switch

Totals Recall Reed Switch

Figure 1.6. Magnet Reed Switch Locations.

Sale $

Kilograms

Overview and Features

H35 Series Operation Manual Back to TOC 7

To obtain Audit Trail information:

1. Hold the black Access Magnet over the Kilograms text (Totals Reed Switch) for a longer period of

time after the Totals Mode is displayed.

2. Once the data scrolls past the Totals Mode the Audit Trail information will appear. Lift and

return the magnet to cycle through:

2.5.2 LAST SALE RECALL SWITCH

The recall switch is behind the “SALE $” print. If dispenser AC power is OFF the recall switch connects the

displays to the battery and displays the last sale.

NOTE: If a pump handle is lifted and the dispenser is activated during this operation, the display returns

to idle.

To recall the last sale with battery power:

•Hold the Access Magnet over the “SALE $” print for approximately 2 seconds.

•The last sale in progress will display for 30 seconds.

2.6 ELECTRO-MECHANICAL TOTALIZER - OPTIONAL

The electro-mechanical totalizer displays cumulative totals in gallon or liter increments for each meter

and therefore each product being dispensed, see Figure 1.1. The totalizer is located below the product

select buttons on each side of the dispenser.

NOTE: Because of rounding methods used in electronic totals, over time electronic totals and electro-

mechanical totals will not match exactly.

Magnet Action Dispenser Display Audit Trail Sub-Menu Description

Touch magnet to Totals

Reed Switch

ECAL 1A, b, c

000001

E-Cal changes for Side 1 meters.

Lift away reengage ECAL 2A, b, c

000001

E-Cal changes for Side 2 meters.

Lift away reengage unitch

00000

Mass Unit Changes (gallons to liters to

imperial gallons).

Lift away reengage 4olrES

0000

Mass resolution changes (0.001 or

0.01).

Otros manuales para H35 Series

Tabla de contenidos

Otros manuales de Equipos marinos de Bennett

Bennett

Bennett LNG Series Manual de usuario

Bennett

Bennett HIGH FLOW H35 Manual de usuario

Bennett

Bennett 621 Manual de usuario

Bennett

Bennett H35 Series Manual de usuario

Bennett

Bennett BOLT Control BCI8000 Manual de usuario

Bennett

Bennett H35 Series Manual de usuario

Bennett

Bennett BOLT Rocker BRC4000 Manual de usuario

Bennett

Bennett SITE MASTER EMV Manual de usuario

Manuales populares de Equipos marinos de otras marcas

Clarion

Clarion CMS2 Manual de reparación

EBS

EBS M7000 Manual de usuario

Kongsberg

Kongsberg M3 Bathy Manual de usuario

NPK

NPK SCS-1002 Manual de usuario

Furuno

Furuno FE-800 Manual de usuario

Harken

Harken 1561 Manual de usuario

Simrad

Simrad DD15 Manual de usuario

Notifier

Notifier FS-BSO Manual de usuario

Raymarine

Raymarine ST40 Manual de usuario

E2S

E2S E2XS112UL Manual de usuario

R2Sonic

R2Sonic 2026 Manual de usuario

COBHAM

COBHAM SAILOR 6000 Manual de usuario

Clarion

Clarion GR10BT Manual de reparación

Raymarine

Raymarine Maxiview ST80 Guía del usuario

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Instrucciones de montaje

Raymarine

Raymarine ST60 Tridata Guía del usuario

olympia electronics

olympia electronics ΒS-531/1/MAR Manual de usuario

Sonic

Sonic 2024 Manual de usuario