Beninca DA.AX Manual de usuario

DA.AX

CENTRALINA A MICROPROCESSORE

CONTROL UNIT WITH MICROCONTROLLER

MIKROCONTROLLER-STEUERUNG

CENTRALE A MICROCONTRÔLEUR

CENTRALITA A MICROPROCESADOR

AUTOMATISMI PER CANCELLI

L8542605

Rev. 07/00/01

Libro istruzioni

Operating instructions

Betriebsanleitung

Livret d’instructions

Libro de instrucciones

UNIONE NAZIONALE COSTRUTTORI

AUTOMATISMI PER CANCELLI, PORTE,

SERRANDE ED AFFINI

UNI

EN ISO

9001

Dichiarazione CE di conformità Déclaration CE de conformité

EC declaration of confirmity Declaracion CE de conformidad

EG-Konformitatserklarung

Con la presente dichiariamo che il nostro prodotto

We hereby declare that our product

Hiermit erklaren wir, dass unser Produkt

Nous déclarons par la présente que notre produit

Por la presente declaramos que nuestro producto

DA.AX

è conforme alle seguenti disposizioni pertinenti:

complies with the following relevant provisions:

folgenden einschlagigen Bestimmungen entspricht:

correspond aux dispositions pertinentes suivantes:

satisface las disposiciones pertinentes siguientes:

Direttiva sulla compatibilità elettromagnetica (89/336/

CCE, 93/68/CEE)

EMC guidelines (89/336/EEC, 93/68/EEC)

EMV-Richtlinie (89/336/EWG, 93/68/EWG)

Directive EMV (89/336/CCE, 93/68/CEE) (Compatibilité

électromagnétique)

Reglamento de compatibilidad electromagnética (89/336/

MCE, 93/68/MCE)

Norme armonizzate applicate in particolare:

Applied harmonized standards, in particular:

Angewendete harmonisierte Normen, insbesondere:

Normes harmonisée utilisées, notamment:

Normas armonizadas utilzadas particularmente:

EN 55022, EN 61000-3-2, EN 61000-3-3, EN 50082-1

Norme e specifiche tecniche nazionali applicate in

particolare:

Applied national technical standards and specifications, in

particular:

Angewendete nationale Normen und technische

Spezifikationen, insbesondere:

Normes et specifications techniques nationales qui ont été

utilisées, notamment:

Normas y especificaciones técnicas nacionales que se

utilizaron particularmente:

UNI 8612

Data/Firma

Direttiva sulla bassa tensione (73/23/CEE, 93/68/CEE)

Low voltage guidelines (73/23/EEC, 93/68/EEC)

Tiefe Spannung Richtlinie (73/23/EWG, 93/68/EWG)

Directive bas voltage (73/23/CEE, 93/68/CEE)

Reglamento de bajo Voltaje (73/23/MCE, 93/68/MCE)

Norme armonizzate applicate in particolare:

Applied harmonized standards, in particular:

Angewendete harmonisierte Normen, insbesondere:

Normes harmonisée utilisées, notamment:

Normas armonizadas utilzadas particularmente:

EN 60204-1, EN 60335-1

Data/Firma

AUTOMATISMI PER CANCELLI

Automatismi Benincà Srl

Via Scamozzi, 3

36030 MONTECCHIO P. VI

ITALIA

TRF1

FF1

VDR2

R18 D1 TCA

FF4

INPUT

230VAC MANT.

OUT

24VAC

FTC

FCA

FCC

P.P.

CHIUDE

F N

COM. APRE CHIUDE

2 3 4 5 6 7 8 9 10 11 12 13 14 15

FF3

DA.AX

SW1

C15

v1.0

R21

R19

R20

U6 U4

R28

6.3A

VDR1 VDR3

RL1

COMUNE

RL2

APRE

RL3

CHIUDE

VDR4

POWER

1 Funz. P.P.

2 Rich. Aut.

3 Funz. Cond.

4 P.P./Apre

C6 C10

R8 R6

+TL

250mA

R23

C13

R15

R11

R16

R12

R17

R13

R14

R10

C12

C11

C14

R22

FUSE

DA.AX Control unit with microcontroller

The microprocessor control unit “DA.AX” can be used with motors having a power not exceeding 500W.

Installation instructions.

a) The electrical installation and functioning logic must comply with current standards.

b) It is advisable to keep the power cables (motor, power supply) detached from the control cables

(push-buttons, photocells, radio). In order to avoid any possible interference it is recommended

to provide for and use two separate sheaths (see EN 60204-1 15.1.3).

c) Before powering the unit, check again all connections which have been carried out.

d) Check the correct presettings of the Dip-Switches.

e) When the unit is powered, the LED “POWER” must be lit; in the negative, check fuses and that

230Vac 50Hz power supply is present between terminals 1 and 2 (INPUT 230VAC - keep to

phase / neutral).

f) The N.C. inputs not used must be connected to the common “+V”.

g) Should the direction of rotation of the motor be reversed, invert the motor wires “OPEN” with

“CLOSE” and the limit switches wires “FCA” with “FCC”.

Input/Output functions

(1,2) INPUT 230VAC= Control unit 230Vac 50 Hz power supply

(respect phase/neutral wire position).

(3,4,5) COM/APRE/CHIUDE= Connection to the corresponding 230Vac 50 Hz motor terminals

(the earth wire (green/yellow) must be connected to the motor housing).

(6,7) OUT 24VAC= 24Vac auxiliary power supply output (100mA max.).

(12) +V= Common connection to all the control inputs.

(9) FTC= Photocell receiver input (n.c. contact).

(10) FCA= Input of limit switch APRE (n.c. contact).

(11) FCC= Input of limit switch CHIUDE (n.c. contact).

(8) P.P.= Input, “PASSO-PASSO” push button or “APRE” push-button according to the Dip-Switch

presetting

(15) CHIUDE= CLOSE button input (n.o. contact).

(13,14) ANT.= Input of radio board antenna

Dip-switch functions

N.B.: Every change of functions have to be done without electricity.

DSW1= This selects the type of functioning of the P.P. button and Remote control.

Off= ”APRE” - ”STOP” - ”CHIUDE” functioning

On= ”APRE” - ”CHIUDE” - ”APRE” functioning.

DSW2= This enables or disables the automatic re-closing - ”TCA TRIMMER”.

Off= Automatic re-closing enabled

On= Automatic re-closing disabled

DSW3= This enables or disables the apartment building function (after the first opening command, the

P.P. button and the Remote control are deactivated).

Off= Apartment building function disabled.

On= Apartment building function enabled.

DSW4= It selects the operation of the “P.P.” input as push-button “PASSO-PASSO” or push-button

“APRE”.

Off= “P.P.” push-button

On= “APRE” push-button

Trimmer functions

TCA= This allows the automatic re-closing time to be adjusted when this is enabled by positioning the

DSW2 Dip-switch on OFF.

Adjustment can be from a minimum of 5 to a maximum of 150 seconds.

The minimum time is obtained by rotating the trimmer completely clockwise.

TL= This allows the working time of the automation to be adjusted. If the limit switches fail, the soft-

ware protection will intervene after this time has elapsed. (Add about 4 sec. to the actual stroke

time of the automation).

Adjustment can be from a minimum of 7 to a maximum of 180 seconds.

The minimum time is obtained by rotating the trimmer completely clockwise.

Note

• The ”STOP” control can be carried out by connecting the normally closed push button between the

common wire of the limit switch and the ”+V” terminal (see drawing).

• If the ”P.P.” input is used as ”APRE” (Dip-switch 4= ON), the automatic closure is not carried out until

the contact remains closed.

FTC

FCA

FCC

STOP button

Limit switch buttons

AUTOMATISMI PER CANCELLI

AUTOMATISMI BENINCÀ Srl - Via Capitello, 45 - 36066 Sandrigo (VI) - Tel. 0444 751030 r.a. - Fax 0444 759728

Otros manuales de Unidad de control de Beninca

Beninca

Beninca CORE Manual de usuario

Beninca

Beninca DA.24V Manual de usuario

Beninca

Beninca DA.BA Manual de usuario

Beninca

Beninca CELL.P Manual de usuario

Beninca

Beninca SA02MA Manual de usuario

Beninca

Beninca KER Manual de usuario

Beninca

Beninca SA.03 Head Manual de usuario

Beninca

Beninca CP.BULL OMI Manual de usuario

Beninca

Beninca RI.624 Manual de usuario

Beninca

Beninca KTE Manual de usuario

Beninca

Beninca BRAIN Manual de usuario

Beninca

Beninca HEADY 24 3B Manual de usuario

Beninca

Beninca SA02E Manual de usuario

Beninca

Beninca BRAINY 24 Manual de usuario

Beninca

Beninca CORE Manual de usuario

Beninca

Beninca DA.AXE Manual de usuario

Beninca

Beninca RI.15K Manual de usuario

Beninca

Beninca ZED-RE Manual de usuario

Beninca

Beninca CP.B24ESA Manual de usuario

Beninca

Beninca CP.J3M Manual de usuario

Beninca

Beninca CP.K Series Manual de usuario

Beninca

Beninca CP.J3-SW Manual de usuario

Beninca

Beninca CP.J3 Manual de usuario

Beninca

Beninca HEADY Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario