Bend-Pak PCL-18B Manual de usuario

PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO

INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT

YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF

THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO

OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.

Manual Revision A5 - Feb. 2020

Manual Part Number 5900170

INSTALLATION AND OPERATION MANUAL

SHIPPING DAMAGE CLAIMS

When this equipment is shipped, concerns for material

damaged in shipment must be noted by the purchaser on

the delivery receipt at the time shipment is received to

ensure proper handling by the shipper.

BE SAFE

Your new lift was designed and built with safety in mind.

However, your overall safety can be increased by proper

training and thoughtful operation on the part of the operator.

DO NOT operate or repair this equipment without reading

this manual and the important safety instructions shown

inside.

1645 Lemonwood Dr.

Santa Paula, CA. 93060, USA

Toll Free 1-800-253-2363

Tel: 1-805-933-9970

www.bendpak.com

Keep this operation manual near the

machine at all times. Make sure that ALL

USERS read this manual.

Portable Column Lifting System

Model: PCL-18B

IMPORTANT

Reference ANSI/ALI ALIS, Safety

Requirements for Installation and Service of

Automotive Lifts before installing lift.

PCL-18B

Portable Column Lift

This instruction manual has been prepared especially for you.

Your new lift is the product of over 40 years of continuous research, testing and development;

it is the most technically advanced lift on the market today.

READ THIS ENTIRE MANUAL BEFORE INSTALLATION & OPERATION BEGINS

RECORD HERE THE LIFT AND

POWER UNIT INFORMATION WHICH IS

LOCATED ON THE SERIAL NUMBER

DATA PLATES ON THE LIFT AND

ON THE POWER UNIT

Power Unit Model # _____________

Power Unit Date Of Mfg. _____________

Power Unit Serial # _____________

This information is required when

calling for parts or warranty issues.

PRODUCT WARRANTY

Our comprehensive product warranty means more than a commitment to you; it’s also a commitment to the value of your

new BendPak lift. For full warranty details contact your nearest BendPak dealer or visit:

http://www.bendpak.com/support/warranty/

OUR LIFTS ARE SHIPPED WITHOUT OIL.

ADD OIL TO POWER UNIT TANK BEFORE USE.

READ SECTION 8 FOR MORE INFORMATION.

IMPORTANT NOTICE

Do not attempt to install this lift if you have never been

trained on basic automotive lift installation procedures.

Never attempt to lift components without proper lifting

tools such as forklift or cranes. Stay clear of any moving

parts that can fall and cause injury. These instructions

must be followed to ensure proper installation and

operation of your lift. Failure to comply with these

instructions can result in serious bodily harm and void

product warranty. Manufacturer will assume no liability

for loss or damage of any kind, expressed or implied,

resulting from improper installation or use of this product.

PLEASE READ ENTIRE MANUAL

PRIOR TO INSTALLATION.

DEFINITIONS OF

HAZARD LEVELS

Identify the hazard levels used in this manual with the

following denitions and signal words:

Watch for this symbol. It means immediate hazards

which will result in severe personal injury or death.

Beware of this symbol. It means hazards or unsafe

practices could result in severe personal injury or death.

Take note of this symbol. It means hazards or unsafe

practices which may result in minor personal injury,

product or property damage.

OWNER’S RESPONSIBILITY

To maintain the lift and user safety, the

owner’s responsibility is to read and

follow these instructions:

t Follow all installation and operation instructions.

t Make sure installation conforms to all applicable Local,

State, and Federal Codes, Rules, and Regulations;

such as State and Federal OSHA Regulations and

Electrical Codes.

t Carefully check the lift for correct initial function.

t Read and follow the safety instructions. Keep them

readily available for machine operators.

t Make certain all operators are properly trained, know

how to safely and correctly operate the unit, and are

properly supervised.

t Allow unit operation only with all parts in place and

operating safely.

t Carefully inspect the unit on a regular

basis and perform all maintenance as

required.

t Service and maintain the unit only

with authorized or approved replacement parts.

t Keep all instructions permanently with the unit and

all decals on the unit clean and visible.

BEFORE YOU BEGIN

NOTIFY THE CARRIER AT ONCE if any hidden loss or

damage is discovered after receipt and request the carrier

to make an inspection. If the carrier will not do so, prepare

a signed statement to the effect that you have notied the

carrier (on a specic date) and that the carrier has failed to

comply with your request.

IT IS DIFFICULT TO COLLECT FOR LOSS OR DAMAGE

AFTER YOU HAVE GIVEN THE CARRIER A CLEAR

RECEIPT. Support claim with copies of the Bill of Lading,

freight bill, invoice, and photographs, if available. BendPak’s

willingness to assist in helping you process your claim does

not make BendPak responsible for collection of claims or

replacement of lost or damaged materials.

Warranty / Serial Number Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Definitions of Hazard Levels . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Owner’s Responsibility . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installer/Operator Agreement/ Protective Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety / Warning Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Section 1 / Selecting Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Section 2 / Floor Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Concrete Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Assembly View / Parts Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Section 3 / Layout / Specifications /Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10

Section 4 / Hydraulic Jacking System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Section 5 / Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Section 6 / Communication Cable and Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Column Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Section 7 / Control Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16

Section 8 / Initial Start-up and PLC System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Section 9 / Testing Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Section 10 / Operation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-23

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-24

Product Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-28

Safe Lift Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-30

Troubleshooting and Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-34

Installation Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Part Breakdowns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-46

Crossbeam Accessory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

TABLE OF CONTENTS

INSTALLER / OPERATOR

PLEASE READ AND FULLY

UNDERSTAND. BY PROCEEDING

YOU AGREE TO THE FOLLOWING:

t I have visually inspected the site where the lift is

to be installed and verified the concrete to be in good

condition and free of cracks or other defects. I understand

that installing a lift on cracked or defective concrete could

cause lift failure resulting in personal injury or death.

t I understand that a level floor is required for proper

installation and level lifting.

t I understand that I am responsible if my floor is of

questionable slope and that I will be responsible for all

charges related to pouring a new level concrete slab if

required.

t I will assume full responsibility for the concrete floor

and condition thereof, now or later, where the above

equipment model is to be installed. Failure to follow

Danger, Warning, and Caution instructions may lead to

serious personal injury or death to operator or bystander

or damage to property.

t I understand that BendPak lifts are designed to be

installed in indoor locations only. Failure to follow

installation instructions may lead to serious personal

injury or death to operator or bystander or damage to

property or lift.

Failure to follow Danger, Warning, and Caution

instructions may lead to serious personal injury or death

to operator or bystander or damage to property.

Please read the entire manual prior to installation.

Do not operate this machine until you have read and

have understood all of the Danger, Warning and

Caution alerts in this manual. For additional copies

or further information, contact:

BendPak Inc.

1645 Lemonwood Dr.

Santa Paula, CA. 93060

1-805-933-9970

www.bendpak.com

INSTALLER / OPERATOR

PROTECTIVE EQUIPMENT

Personal protective equipment helps to make installation

and operation safer; however, it does not take the place

of safe operating practices. Always wear durable work

clothing during any installation and/or service activity.

Shop aprons or shop coats may also be worn, however

loose-fitting clothing should be avoided.

Tight-fitting leather gloves are recommended

to protect the technician’s hands when

handling parts. Sturdy leather steel-toe

work shoes and oil resistant soles should

be used by all service personnel to help

prevent injury during typical installation and

operation activities.

Eye protection is essential during installation

and operation activities. Safety glasses with

side shields, goggles, or face shields are

acceptable. Back belts provide support

during lifting activities and are also helpful in

providing worker protection. Consideration

should also be given to the use of hearing protection if

service activity is performed in an enclosed area, or if

noise levels are high.

THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED

COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OR YOURSELF AND OTHERS

AND CAN CAUSE PERSONAL INJURY OR DEATH. READ AND FOLLOW ALL INSTRUCTIONS IN

THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

1. Carefully remove the crating and packing materials.

CAUTION! Be careful when cutting steel banding

material as items may become loose and fall causing

personal harm or injury.

2. Check the voltage, phase and proper amperage

requirements for the motor shown on the motor plate.

Wiring should be performed by a certied electrician only.

IMPORTANT SAFETY INSTRUCTIONS

Read these safety instructions entirely

IMPORTANT NOTICE

Do not attempt to install this lift if you have never been trained on

basic automotive lift installation procedures.

Never attempt to lift components without proper lifting tools such as forklift or cranes.

Stay clear of any moving parts that can fall and cause injury.

1. READ and understand all instructions and all safety

warnings before operating lift.

2. Care must be taken as burns can occur from touching

hot components.

3. DO NOT operate equipment with a damaged cord or

if the equipment has been dropped or damaged until it has

been examined by a qualied service person.

4. DO NOT let a cord hang over the edge of the table,

bench, or counter or come in contact with hot manifolds or

moving fan blades.

5. If an extension cord is necessary, a cord with a current

rating equal to or more than that of the equipment should be

used. Cords rated for less current than the equipment may

overheat. Care should be taken to arrange the

cord so that it will not be tripped over or pulled.

6. ALWAYS unplug equipment from

electrical outlet when not in use. Never use

the cord to pull the plug from the outlet. Grasp

plug and pull to disconnect.

7. Let equipment cool completely before

putting away. Loop cord loosely around cable

hook when storing.

8. DO NOT operate equipment in the vicinity of open con-

tainers of ammable liquids (gasoline) to reduce the risk of

re.

9. Adequate ventilation should be provided when working

on operating internal combustion engines.

10. Keep hair, loose clothing, ngers, and all parts of body

away from moving parts. Keep feet clear of lift

when lowering. Avoid pinch points.

11. DANGER! To reduce the risk of electric

shock, do not use on wet surfaces or expose

to rain. The power unit used on this lift contains

high voltage. Disconnect power at the recep-

tacle or at the circuit breaker switch before

performing any electrical repairs. Secure

plug so that it cannot be accidentally plugged

in during service. Or mark circuit breaker

switch so that it cannot be accidentally

switched on during service.

12. Use only as described in this manual.

Use only manufacturer’s recommended

attachments.

13. ALWAYS WEAR SAFETY GLASSES.

Everyday eyeglasses only have impact

resistant lenses, they are not safety

glasses.

14. CONSIDER WORK ENVIRONMENT. Keep work area

clean. Cluttered work areas invite injuries. Keep areas well lit.

15. GUARD AGAINST ELECTRIC SHOCK. This lift must be

grounded while in use to protect operator from electric shock.

Never connect the green power cord wire to a live terminal.

This is for ground only.

16. Only trained operators should operate this lift. All

non-trained personnel should be kept away from the work

area. Never let non-trained personnel come in contact with,

or operate lift.

17. DO NOT override self-closing lift controls.

18. CLEAR AREA if vehicle is in danger of falling.

19. ALWAYS make sure the safeties are

engaged before attempting to work on or

near a vehicle.

20. WARNING! RISK OF EXPLOSION.

This equipment has internal arcing or

sparking parts which should not be

exposed to ammable vapors. This

machine should not be located in a recessed area or below

oor level.

21. MAINTAIN WITH CARE. Keep lift clean for better and

safer performance. Follow manual for proper lubrication and

maintenance instructions. Keep control handles, buttons and

displays dry, clean and free from grease and oil.

22. Check for damaged parts. Check for alignment of

moving parts, breakage of parts or any condition that may

affect operation of lift. Do not use lift if any component is

broken or damaged.

23. NEVER remove safety related components from the lift.

Do not use lift if safety related components are missing or

damaged.

24. STAY ALERT. Use common sense and watch what you

are doing. Remember, SAFETY FIRST.

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

These instructions must be followed to ensure proper installation and operation

of your lift. Failure to comply with these instructions can result in serious

bodily harm and void product warranty. Manufacturer will assume no liability for

loss or damage of any kind, expressed or implied, resulting from

improper installation or use of this product.

PLEASE READ ENTIRE MANUAL PRIOR TO INSTALLATION

SECTION 1

(SELECTING SITE)

Before installing your new lift, check the following.

1. LIFT LOCATION: Always use architectural plans

when available. Check the layout dimension against the

oor plan requirements, making sure that adequate space

is available.

2. OVERHEAD OBSTRUCTIONS: The area where the

lift will be located should be free of overhead obstructions

such as heaters, building supports, electrical lines, etc.

3. DEFECTIVE FLOOR: Visually inspect the site where

the lift is to be installed and check for cracked or defective

concrete.

4. Lift is designed for INDOOR INSTALLATION ONLY.

Outdoor installation is prohibited. Always follow warnings

illustrated on equipment labels.

SECTION 2

(FLOOR REQUIREMENTS)

This lift must be installed on a solid level concrete

floor with no more than 3-degrees of slope. Failure

to do so could cause personal injury or death.

A level oor is suggested for proper use, installation

and level lifting. If a oor is of questionable slope, con-

sider a survey of the site and/or the possibility of pouring

a new level concrete slab.

t DO NOT install or use this lift on any asphalt surface

or any surface other than concrete.

t DO NOT install or use this lift on expansion seams

or on cracked or defective concrete.

t DO NOT install or use this lift on a second / elevated

oor without rst consulting building architect.

t DO NOT install or use this lift in extremely damp

environments.

t DO NOT install this lift outside. It is only approved for

indoor installations.

t Refer to ANSI/ALI ALIS Standard (R2015) Safety

Requirements for Installation and Service for more

information about safely installing your Lift.

ALL MODELS MUST BE INSTALLED ON CONCRETE

ONLY CONFORMING TO THE MINIMUM

REQUIREMENTS SHOWN ABOVE. NEW CONCRETE

MUST BE ADEQUATELY CURED BY AT LEAST

28 DAYS MINIMUM.

OUR LIFTS ARE SHIPPED WITHOUT OIL.

ADD OIL TO POWER UNIT TANK BEFORE USE.

LIFT MODEL CONCRETE REQUIREMENTS

PCL-18B 5” Min Thickness

When removing the lift from shipping angles, pay close attention as the columns can slide and can cause injury. Be

careful when cutting steel banding material as items may become loose and fall causing personal harm or injury.

Prior to removing the pallets make sure the posts are held securely by a fork lift or some other heavy lifting device.

PCL-18B PARTS INVENTORY

Be sure to take a complete inventory of parts prior to beginning installation.

Description Qty

Column Assembly 4

Carriage Assembly 4

Fork Arm Weldment 8

Displacement Sensor Cover 4

Control Box Assembly 4

Motor Cover Assembly 4

Parts Box (Packing List Enclosed) 4

Hydraulic Jack 4

Hydraulic Power Unit 4

Displacement Sensor

Cover

Control Box

Assembly

Hydraulic Jack

Motor Cover

Assembly

Carriage

Assembly

Column

Assembly

Fork Arm

Weldment

PCL-18B

Maximum Column Capacity Each Column 18,000 Lbs. / 8,165 Kg

Conguration Sold in sets of 2, 4 or 6 columns

Min. Column Height 97.5” / 2,572 mm

Maximum Lifting Height 71.5” / 1,889 mm

Length Lifting Fork 13.6” / 360 mm

Overall Length / Depth 47.5” / 1,206 mm

Width Inside Lifting Fork / Min. 9.5” / 241 mm

Width Inside Lifting Fork / Max. 22.7” / 576 mm

Overall Width 44” / 1,160 mm

Turning Circle 40” / 1,016 mm

Column Weight Each 1450 lbs. / 657 kg.

Lifting Speed 85 Seconds

Motor / 2HP * 208-240 V 50/60 Hz, 3 Phase

* Special Voltages Available Upon Request

The design, material and specications are subject to change without notice.

SECTION 3

(LAYOUT)

CLEARANCES

LIFT HEIGHT CLEARANCE NOTE: There must be a 148” MIN distance from ground to the nearest

overhead obstruction to clear the lift at full rise.

Otros manuales para PCL-18B

Tabla de contenidos

Otros manuales de Columna elevadora de Bend-Pak

Bend-Pak

Bend-Pak XPR-10XLS Manual de usuario

Manuales populares de Columna elevadora de otras marcas

Linak

Linak BL1 Manual de usuario

progressive automations

progressive automations FLT-03-2-2 Manual de usuario

Clemens Technologies

Clemens Technologies S-2R Manual de usuario

Ewellix

Ewellix CPSM Manual de usuario

MAHA

MAHA RGA UC Manual de usuario

Ewellix

Ewellix CPMT Manual de usuario

Dhollandia

Dhollandia DH-VO.20.K9 Manual de usuario

Linak

Linak TECHLINE ELEVATE - LC3 IC Manual de usuario

GE FineLINE 35 oligo Manual de usuario

Mohawk

Mohawk LMF-12 Documento técnico

OMA

OMA 511 Manual de usuario

Linak

Linak DL8IC Manual de usuario

Rotary

Rotary MCH418 Manual de usuario

progressive automations

progressive automations FLT-06 Manual de usuario

IDEAL

IDEAL MSC-18K-X-236 Manual

Ewellix

Ewellix CPMA Series Manual de usuario

Linak

Linak DESKLINE DL5 IC Manual de usuario

Ewellix

Ewellix LIFTKIT-0S-601 Manual de usuario