Bellfires VENTO CLASSIC SMALL Guía
Bellfires wishes you many cosy evenings with your new Bellfires gas fire
This document is an essential part of your gas fire.
Read it carefully before installation and maintenance
of the gas fire and keep it in a safe place!
INSTALLATION INSTRUCTIONS &
MANUAL FOR MAINTENANCE
VENTO CLASSIC SMALL
Gas fire with closed combustion system
Serial number:
Production date:
3
Bellfires English
Installation instructions
BELLFIRES GAS FIRE WITH CLOSED COMBUSTION SYSTEM:
Vento Classic Small (VCS)
4
Bellfires English
Installation instructions
5
Bellfires English
Installation instructions
CONTENTS
Page
1. INSTALLATION INSTRUCTIONS .............................................................. 7
2. MAINTENANCE ......................................................................................... 50
3. FAULTS ...................................................................................................... 51
4. DISMANTLING / ASSEMBLING OF THE GLASS,
THE REGULATOR AND BURNER ..
...
....................................
.
........
........
. 52
5. ELECTRICAL DIAGRAM .............................................................
.........
..... 54
6. DIMENSIONS ............................................................................................ 55
7. TECHNICAL DETAILS/REGULATIONS .................................................... 56
8. REPLACEMENT PARTS LIST .................................................................. 58
9. DISPOSAL OF PACKAGING AND APPLIANCE ....................................... 60
The installation must only be carried out by a
“Gas Safe Register” registered installation engineer.
IMPORTANT
6
Bellfires English
Installation instructions
7
Bellfires English
Installation instructions
1 INSTALLATION INSTRUCTIONS
1.1 GENERAL
The gas fire must be positioned and connected as a “room sealed system” (balance
flue) appliance by a “Gas Safe Register” registered gas installation engineer in
accordance with the following installation instructions, nationally and locally applicable
regulations (see “Technical Details/ Regulations” at the rear of this manual). If you have
any queries regarding the installation, please consult your local gas company.
Important: Before beginning the installation, check that the details on the
rating plate correspond to the gas type and pressure to which
the appliance will be connected.
The appliance is factory set to the correct nominal heat input. The pilot light is set to the
correct level of consumption.
The appliance has a Ø100 mm - Ø150 mm concentric connection for extracting the flue
gases and supply of combustion air.
It is possible to install the gas fire with either a wall or roof outlet.
The roof connection must be carried out using the concentric flue system Ø100 mm -
Ø150 mm. The fumes are exhausted naturally to the outside environment through the
inner Ø100 mm pipe whereas the combustion air supply passes between the Ø100 mm
and Ø150 mm pipes.
The wall connection must be carried out using the concentric flue system Ø100 mm -
Ø150 mm. The flue gases are evacuated outside by means of natural draft through the
internal pipe of Ø100 mm, whereas the combustion air is supplied between the pipes of
Ø100 mm and Ø150 mm.
The gas fire can be installed in a completely sealed or mechanically ventilated house
without extra ventilation and/or fume extraction.
The gas fire can be installed as an insertion into an existing open fire place or as
a built-in appliance in a new fire place.
In order to prevent the fireplace heating up excessively, it must be properly
ventilated by installing vents at the top and bottom of the fireplace.
If an existing chimney is to be used, please consult your installer first. If the chimney
was previously used for a wood or coal fire, then it should be cleaned by an expert.
8
Bellfires English
Installation instructions
N.B. If any part is missing, please contact your dealer.
1.3 INCLUDED
1.2 CONCENTRIC FLUE SYSTEMS Ø100 MM - Ø150 MM
• Bellfires (Muelink & Grol system)
• Poujoulat (PGI system)
• Ontop (Metaloterm US system)
The gas fire, in combination with the concentric flue system [Ø100 mm - Ø150 mm]
(rigid and/or flexible)
for the brands Bellfires (Muelink & Grol system), Poujoulat (PGI
system) or Ontop (Metaloterm US system), has been approved in accordance with the
European CE-norm for gas appliances and may therefore be used only with these
systems. The permitted components for these systems are listed in Chapter 1.6.2.
The guarantee on the appliance lapses if it is installed, fully or partially, with other
components or a different flue system.
The concentric flue [Ø100 mm - Ø150 mm] systems can be used with either a newly-
built or existing chimney.
Set documentation - Instructions for use
- Installation instructions
Attributes - Ceramic log set
9
Bellfires English
Installation instructions
1.4 OPTIONS AND ACCESSORIES
The following options and accessories can be supplied by your dealer:
Part no Accessorie
3........ Bellfires (M&G) concentric flue system
See component summary
3........ Poujoulat (PGI) concentric flue system
See component summary
3........ Ontop (Metaloterm US) concentric flue system
See component summary
Part no Option
311960 Mantle iron L = 1000 mm
10
Bellfires English
Installation instructions
1.5 PREPARATION FOR INSTALLATION
The following preparation must be carried out before the gas fire can be installed.
1.5.1 Instructions for positioning the outlet
1.5.1.1 Positioning the outlet for correct operation:
Roof-mounted outlet:
Figure 1: Roof-mounted outlet
This must be positioned at least 0.5 m from the roof edge;
the apex of the roof can be disregarded.
Wall-mounted outlet:
Figure 2: Wall-mounted outlet
This must be positioned at least 0.5 m from:
• the corner of the building.
• the roof overhang, the rain gutter.
• balconies etc., unless the exhaust construction
extends to at least the face of the protruding section.
>0.5 m
>0.5 m
Otros manuales para VENTO CLASSIC SMALL
1
Tabla de contenidos
Otros manuales de Chimenea de interior de Bellfires
Bellfires
Bellfires Smart Bell 65/55 MF Instrucciones de funcionamiento
Bellfires
Bellfires VIEW BELL DERBY 3 LF Manual de instalación y operación
Bellfires
Bellfires BCC-28 Tall Manual de usuario
Bellfires
Bellfires DERBY LARGE 3 CF Manual de usuario
Bellfires
Bellfires HORIZON BELL XS 3 CF Guía
Bellfires
Bellfires UNICA-2 40 Manual de usuario
Bellfires
Bellfires Smart Bell Panorama 45/59 MF Manual
Bellfires
Bellfires BELL SMALL 3 CF Manual de usuario
Bellfires
Bellfires HORIZON BELL SMALLTUNNEL 3 Guía de configuración
Bellfires
Bellfires Smart Bell 65 MF Manual
Bellfires
Bellfires CLASSIC BELL MEDIUM 3 PF Manual de instalación y operación
Bellfires
Bellfires VENTO CLASSIC SMALL Manual de instalación y operación
Bellfires
Bellfires DERBY SMALL 3 LF Manual de instalación y operación
Bellfires
Bellfires SMART BELL 80 Guía
Bellfires
Bellfires Wi-fi box Manual de usuario
Bellfires
Bellfires Box Gas Panorama 73/52 MF Manual
Bellfires
Bellfires Smart Bell 75/55 MF Manual
Bellfires
Bellfires Room Divider Large 3 Manual de usuario
Bellfires
Bellfires UNC-2 40 Guía
Bellfires
Bellfires Smart Bell 65 Manual
