Belkin F5D8231-4 - N1 Wireless Router Guía de inicio rápido
F5D8231-4 Operational Principle
1. FUNCTION DESCRIPTION
The Belkin F5D8231-4 Wireless-11N Router is a next generation Router with
built-in wireless access point (AP), 4-port Fast Ethernet (10/100Base-T) switch for
LAN, and 1 Fast Ethernet port for WAN connection. The Router operates on
2.4GHz frequencies, which conforms to the IEEE 802.11b/g wireless standards,
and the draft 802.11n specification. The router features Atheros’s
draft-802.11n-compliant radio in 2x3 (TX/RX) configuration offering breakthrough
performance and enhanced coverage to it’s WiFi network. The Router is to be
used with either a Broadband ADSL or Cable Modem via the WAN port to share
broadband connections with up to 4 computers via the LAN ports and 32
computers via the WLAN. Each LAN port supports 10/100 Base-T Networks with
auto sensing and switching compatibilities. The Router’s Next Gen EZ install
software operates on Microsoft’s Windows 2000 and XP, and on Mac OS X. The
Router can be configured through a web-browser interface. The product is
designed for the home and small office and will be available through major
retailers and online retailers.
The F5D8231-4 uses the Marvell 88F5180N CPU as the micro-controller and
it offers a memory configuration of 4M Bytes Flash and 32MBytes DDR RAM
This device derives its power from a 12V DC power adapter which needs to
be converted to 3.3V, 2.5V, 1.5V, 1.4V and 1.2V.
The functional requirements of the system are as follows:
1. CPU Marvell 88F5180n 333MHz
2. CODE SIZE 4Mbyte
3. SDRAM 32Mbytes
4. Switch Marvell 88E6061
5. WAN Port One RJ45 port with auto negotiation
6. LAN Port Four RJ45 port with LED and auto negotiation
7. Power Adapter DC 12V/1.2A
8. LEDs Refer to Table 1
9. Reset button Reset to factory default by pressing 5 seconds
11. EMC Class–B
12. PCB Layout 4 layers
Table 1: LED Table
Label Activity Description
OFF Wireless security is OFF
Wireless Security Solid Blue Wireless security is ON
OFF Wireless computer is not present
Solid Blue Wireless computer is connected to the Router
Wireless Computer
Status
Blinking Amber Problem with wireless computer connecting properly
to the Router (Pending feasibility confirmation with
ODM) Our suggestion now is
when there is at least one wireless computer cannot
access the router, then blinking amber.
Need marvell’s support to see if marvell driver can
report some of wireless computer is power on, but
has problem to associate. This may be not doable.
OFF Wired computer is not present
Solid Blue Wired computer is connected to the Router
Wired Computer
Status Blinking Amber Problem with wired computer connecting properly to
the Router (Pending feasibility confirmation with
ODM) Could have the same problem with the
wireless computer.
OFF Router is OFF
Blinking Blue Router is booting up
Router / Power
Status Solid Blue Router is ON and ready
OFF Wireless is OFF
Wireless Status Solid Blue Wireless is ON
Solid Blue Router is connected to Modem and functioning
properlyModem/WAN Status Blinking Amber Problem with Modem (such as boot failure, etc.)
Blinking Blue Router is attempting to connect to the Internet
Solid Blue Router is connected to the Internet
Internet/Connected Blinking Amber Router is NOT connected to the Internet
Link/Act Green Indicate that LAN is connected or there is data
transactionLAN1 Speed Indicate that the connect is 10baseT or 100baseT
Link/Act Green Indicate that LAN is connected or there is data
transaction
LAN2 Speed Indicate that the connect is 10baseT or 100baseT
Link/Act Green Indicate that LAN is connected or there is data
transactionLAN3 Speed Indicate that the connect is 10baseT or 100baseT
Link/Act Green Indicate that LAN is connected or there is data
transaction
LAN
LAN4 Speed Indicate that the connect is 10baseT or 100baseT
2. Block Diagram
The HW Block Diagram as below:
Operating Frequency in USA: 2412-2462 MHz
Operating Frequency in Europe: 2412-2472 MHz
3. Operational Principle
1). Power on the DUT, then connect WAN port with PC1 and LAN port with PC2.
2). Set PC1(Connected with WAN) IP as:
IPAddress:10.10.10.11;
Subnet Mask:255.255.255.0;
Gateway:10.10.10.1.
3). PC2(Connected with LAN) can get IP address from F5D8231-4 and the default
IP subnet is 192.168.2.0. So PC2’s IP address may be 192.168.2.x.
4). Open the Internet Explorer and type theAddress: 192.168.2.1. Then press
“Enter”.
5)WAN Setting
Step1
Step2
Step3
Step4
Step5
Step6
Step7ÆCompleted
6). Then we can ping PC1 from PC2 (ping 10.10.10.11)
7). LAN subnet setting (If need)
Step1
Step2
Step3
8). WLAN setting
Step1
Step2
Step3
Then can use a PC3 with wireless module to connect with the DUT.
Otros manuales para F5D8231-4 - N1 Wireless Router
3
Tabla de contenidos
Otros manuales de Enrutador inalámbrico de Belkin
Belkin
Belkin F5D7234np4 Manual de usuario
Belkin
Belkin F5D7233au Manual de usuario
Belkin
Belkin F6D3230-4 Manual de usuario
Belkin
Belkin Surf + 8820ed00372_F7D2301_v1 Manual de usuario
Belkin
Belkin F5D6231-4 - Wireless Cable/DSL Gateway... Manual de usuario
Belkin
Belkin AC1750 DB Manual de usuario
Belkin
Belkin F5D7230au4 Manual de usuario
Belkin
Belkin PM01218ea Manual de usuario
Belkin
Belkin F5D8236-4 Manual de usuario
Belkin
Belkin VISION N1 Manual de usuario
Belkin
Belkin F5D7234-4 Manual de usuario
Belkin
Belkin AC1200 DB Manual de usuario
Belkin
Belkin F7D3302 Manual de usuario
Belkin
Belkin Wireless G Router Manual de usuario
Belkin
Belkin F9K1108v1 8820-00973 Rev. A00 Manual de usuario
Belkin
Belkin VISION N1 Manual de usuario
Belkin
Belkin SURF N 15 N150 Manual de usuario
Belkin
Belkin F5D8233-4 Manual de usuario
Belkin
Belkin F5D8232-4 - N1 Vision Wireless Router Manual de usuario
Belkin
Belkin AX3200 Manual de usuario
