Belkin F5D5230 Manual de usuario

Belkin Components

501 West Walnut Street

Compton • CA • 90220 • USA

310.898.1100

Mac is a registerd trademark of Apple Computer, Inc. P73882

belkin.com

Belkin Components, Ltd.

Unit 13 • Gatelodge Close • Round Spinney

Northampton • Northants • NN3 8RX • United Kingdom

+44 (0) 1604678300

Belkin Components, Ltd.

7 Bowen Cresent • West Gosford

NSW 2250 • Australia

+61 (2) 4372 8600

4-Port Cable/DSL

Gateway Router

Quick Setup Guide for Mac®

F5D5 30

Setting up the Router is accomplished in three easy steps:

1. Connect the Router to your network.

2. Configure your computer’s TCP/IP settings.

3. Configure the Router to your ISP’s settings.

Step 1: Connect the Router to your network

1. Power down your equipment.

2. Connect a network cable between each of your computers and the Router.

Connect each Mac to one of the ports on the rear of the Router labeled 1–4.

Do not connect a computer to the port labeled “WAN”.

3. Connect a network cable between the Router and your cable or

DSL modem.

Be sure this cable is plugged into the port labeled "WAN" on the Router.

4. Power on the cable or DSL modem.

BELKIN

GATEWAY

ROUTER

5. Select your connection type (this information is provided by your ISP) and click

"Select". Depending on your selection, you will see the "Static IP Address" page or

the "PPPoE" page. Enter the required values provided by your ISP and click "Enter".

6. The “MAC Cloning/Entry” screen will appear. If your ISP binds your connection to

the MAC address of your network adapter, click "Clone MAC Address" or enter the

MAC address here. Press “Enter”.

Your Router has been set up to communicate with your ISP.You should have Internet

access at this point. If you are having trouble, see the “Troubleshooting” section in the

user’s manual.

5. Connect the power adapter to the Router.

6. After the cable or DSL modem and the Router are turned on, the Router’s

WAN link light should be on. This indicates that the modem and the Router

are connected to each other.

7. Turn on the rest of your computers.

After your computers boot up, a LAN link light (on the front of the Router) will

be on for each port to which a computer is connected. These lights are your

means to verify that your computers are connected to the Router.

Step 3: Configure the Router to your ISP’s settings

1. Using the computer that was originally connected directly to the cable or DSL

modem, launch your browser. Note: You can access the setup utility from any

computer on the network, however, use the original computer for this procedure at

this time.

2. In the address bar, type the following address: 192.168.2.1.The Router login screen

will appear. Enter "Admin" in the User Name field, and do not enter anything in the

"Password" field. Click "OK".

3. The Router’s status page will appear.

4. Click on "Initial Setup" in the top left-hand corner. The following page will appear.

Step : Configuring TCP/IP for dynamic IP configuration

Your computer will communicate with the Router through TCP/IP. To configure

your Mac computer’s TCP/IP settings to communicate with the Router, follow the

steps below.

1. Pull down the “Apple” menu. Select "Control Panels" and select "TCP/IP".

2. At "ConnectVia:", choose either "Ethernet Built In" or "Ethernet" based on your

Mac computer’s interface.

3. At "Configure:" choose "Using DHCP Server".This will tell the computer to obtain

an IP address from the Router.

4. Close the window.The following window will appear. Click "Save".

5. Restart the computer.

You are now finished with dynamic IP configuration. Perform this operation for each

computer that you will be connecting to the Router.

When finished configuring yourTCP/IP settings, you need to start File Sharing to enable.

Otros manuales para F5D5230

Este manual sirve para los siguientes modelos

Otros manuales de Enrutador de red de Belkin

Belkin

Belkin F9K1104 Manual de usuario

Belkin

Belkin VoIP Manual de referencia

Belkin

Belkin F9K1113 v5 Manual de usuario

Belkin

Belkin F5D7230au4P Manual de usuario

Belkin

Belkin F6D6230-4 v1 Manual de usuario

Belkin

Belkin F9K1002V1 Manual de usuario

Belkin

Belkin Basic Manual de usuario

Belkin

Belkin 802.11g Wireless Ethernet Bridge Manual de usuario

Belkin

Belkin F9K1121v1 Manual de usuario

Belkin

Belkin F5D52314 - Cable/DSL Gateway Router Manual de instrucciones

Belkin

Belkin F9K1105V2 Manual de usuario

Belkin

Belkin WIRELESSBRIDGE GERMAN Guía de inicio rápido

Belkin

Belkin Bob Manual de usuario

Belkin

Belkin F6D4230-4 Manual de usuario

Belkin

Belkin F1PI241EGau Guía de referencia

Belkin

Belkin F5D5230-F Manual de usuario

Belkin

Belkin F5D52314 - Cable/DSL Gateway Router Manual de usuario

Belkin

Belkin SURF N300 Manual de usuario

Belkin

Belkin PARTAGE DE DOSSIER AVEC UN ROUTEUR Instrucciones de montaje

Belkin

Belkin F5D92304 - Wireless G Plus MIMO Router Manual de usuario

Belkin

Belkin AC 1600 DB Manual de usuario

Belkin

Belkin F7D3301 Manual de usuario

Belkin

Belkin OmniView 5000HQ Manual de usuario

Belkin

Belkin FILTRAGE DE MAC ADRESSE Instrucciones de montaje

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad