Belkin F1PG200ENau Manual de instrucciones

Applies to:

F1PG200ENau –Belkin Analogue Telephone Adapter (ATA)

Firmware release notes

1. Voice over IP registration indicator and error codes

2. Error ‘482 loop detected’ fixed. This error is caused if the modem loses DSL sync and

the ATA will then try to connect to the next available SIP server, obviously connection

will fail as there is no DSL sync. Once the DSL becomes active again the ATA no

longer sits waiting for user intervention to re-connect and the ATA will gauge DSL

sync and re-establish connectivity to the SIP server. -

http://www.ietf.org/rfc/rfc2782.txt

3. OOB signalling –default is set to info (RFC 2976) for support for touch tone menu

options.

Introduction

From time to time Belkin releases new firmware which has enhancements or fixes to

the previous releases of firmware. Firmware resides on the networking product in

question and acts similar to an operating system on a computer.

This guide will explain the changes to the latest release of firmware for the ATA and

will also explain how to perform an upgrade in step by step format.

Before you begin:

You will need:

•Belkin ATA VoIP unit

•Power cable

•Network cable

•PC with network card

•Discovery tool –this was included on the supplied CDROM –if you do not have this

software please download from the following link:

http://www.belkin.com/support/download/download.asp?download=F1PG200ENau&l

ang=1&mode=

•Firmware for the ATA which you need to download and save on to your hard drive,

remember where you saved this firmware as you will need it shortly.

Please download this firmware from

http://www.belkin.com/support/download/download.asp?download=F1PG200ENau&l

ang=1&mode=

Hardware check:

•Your computer is switched on and connected to your router or modem

•The VoIP unit is switched on and connected to your router or modem

•Network cable connected from PC to router and the ATA is connected to the router as

per the following diagram.

•You can surf the web

1) Open and run the ATA Discovery Tool (located on CD provided with ATA, or

download from

http://www.belkin.com/support/download/download.asp?download=F1PG200ENau&l

ang=1&mode=

–run the software or insert the CDROM and after a few moments the software will

run and find any attached ATA devices.

2) The Discovery Tool will find the ATA, highlight the listing then click Open

3) The Login page will appear. Type in your current password (or the default password

of admin) then click LOGIN

4) On the left hand side of the screen click Advanced Setup

5) You will now be presented with more options in the menu on the left. Click Utilities

then choose Firmware Update

6) Click the browse button, located in the centre of the screen

7) You will now be asked to browse for the file you downloaded earlier. Browse to this

file and click Open

8) Click Update, two warnings will now appear, click OK on each warning.

NB –Progress bar will indicate the progress at the bottom of the screen in

percentage.

9) Once the Firmware Update process has completed, you will need to restart the ATA

by clicking the Restart ATAbutton

When the prompt asks you to restart please click yes.

The ATA will restart and take you back to the Login page. You can now Login to the ATA

again by typing in your password and you can confirm the Firmware Version which will be

shown in the top left of the screen.

Finally you will need to perform a factory reset of your ATA so you can continue using the

ATA with the newer firmware. Before conducting a factory reset ensure that you have your

VoIP phone number and password handy –write this information below to assist you later:

VoIP phone number ______________________

VoIP Password __________________________

To perform a factory reset follow these steps:

1. If you are already not logged in to your ATA then log in to the ATA using the method

described in steps 1-3 above

2. Click on advanced set up.

3. Under utilities\restore factory defaults, click on restore factory defaults.

4. Click restore defaults

5. Click OK, click OK again

6. Click restart ATA

7. Click OK –the router will now take a number of seconds to reboot.

8. Once the router has restarted type in your password again andlog in to the ATA.

9. Click on set up wizard in the top left of the screen below the iiNet logo.

10. Place a tick in the box for VoIP Account 1 or 2 and enter your VoIP Phone number

(with no spaces) and VoIP password.

On the back of the physical ATA unit you will see two ports for the telephone cord,

ensure that you have physically connected the telephone in the corresponding

physical Line 1 or Line 2 port in the back of the ATA unit.

11. Select the state in Australia that you are residing in from the drop down menu next to

the state option.

12. Ensure you have the correct details entered with no spaces andthen click on the

apply changes button.

13. Click on the ‘restart ATA’ button

14. Click ‘OK’ –the ATA will restart and take approximately 14 seconds.

15. You should notice the lights on the front of the ATA will illuminate –you should see

the following lights:

a) Power -

b) Connected –

c) and either phone line 1 or 2 illuminated.

Troubleshooting

If, after completing the above steps you do not see either phone line 1 or 2

illuminated please ensure that you are connected to the internet by trying to surf the

web. If you are confident you are connected to the internet then please ensure that

you have entered your VoIP phone number and password correctly (step 10 through

to 14 above). If after checking these two issues you still see no line 1 or 2

illumination then please turn off the ATA and wait for 1 hour before turning the ATA

back on –if after a few minutes the ATA Line 1 or 2 light does not illuminate please

contact Belkin technical support on 1800 235546.

Otros manuales para F1PG200ENau

Tabla de contenidos

Otros manuales de Adaptador de Belkin

Belkin

Belkin F5D4081 Manual de usuario

Belkin

Belkin F8Z452ea Manual de usuario

Belkin

Belkin F5U514 Manual de usuario

Belkin

Belkin F5L043-DL Manual de usuario

Belkin

Belkin Powerline AV Networking Adapters Manual de usuario

Belkin

Belkin F6D4050 Manual de usuario

Belkin

Belkin Bluetooth USB Adapter F8T012 Manual de usuario

Belkin

Belkin PM01146EA-A F5D4047V2 Manual de usuario

Belkin

Belkin F5D8051 Manual de usuario

Belkin

Belkin Smartbeam F5U235ea Manual de usuario

Belkin

Belkin F5D4077 Manual de usuario

Belkin

Belkin F4U047-RS Manual de usuario

Belkin

Belkin F8T008 Manual de usuario

Belkin

Belkin F5U206 Manual de usuario

Belkin

Belkin G+MIMO Manual de usuario

Belkin

Belkin MIRACAST VIDEO ADAPTER Manual de usuario

Belkin

Belkin F5U002-BLU Guía

Belkin

Belkin F5D5055 Manual de usuario

Belkin

Belkin SCREENCAST F7D4501 Manual de usuario

Belkin

Belkin F5U003-MAC Manual de usuario

Belkin

Belkin SURF N300 Manual de usuario

Belkin

Belkin F8T001 Manual de instrucciones

Belkin

Belkin F7D4550 Manual de usuario

Belkin

Belkin F5D4071 Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario