BEL Engineering I-Thermo M5 Series Manual de usuario

Filename:QUICK_GUIDE_BILANCE_M5_EN+IT+POR_rev11;April16

Declaration of Conformity

EC-Konformitätserklärung

EC-Déclaration de conformité

EC-Dichiarazione di conformità

EC-Declarção de conformidad

EC-Declaration of conformity

EC-Declaración de conformidad

BEL Engineering s.r.l., Via Carlo Carrà 5 Monza 20900 (MB) ITALY

Declaration of conformity

We hereby declare that the product to which this declaration refers

complies with the following standards.

Konformitätserklärung

Wir erklären hiermit, dass das Produkt, auf das sich diese Erklärung

bezieht, mit den nachstehenden Normen übereinstimmt.

Déclaration de conformité

Nous déclarons avec cela responsabilité que le produit, auquel se

rapporte la présente déclaration, est conforme aux normes citées ci-après.

Dichiarazione di conformità

chiariamo con ciò che il prodotto al quale la presente dichiarazione si

riferisce è conforme alle norme di seguito citate.

Declarção de conformidade

Manifestamos en la presente que el product al que se refiere esta

declaración està de acuerdo con las normas siguientes..

Declaración de

conformidad

Declaramos por meio da presente que o produto no qual se refere esta

declaração, corresponde às normas seguintes

Electronic Balance: Series i-Thermo M5

Euro

pean Directive

Harmonized Standard

2014/30/EU (EMC) EN 61326-1:2013

2014/35/EU (LVD) EN 61010-1:2010

EN 61010-2-010:2014

2011/65/EU (RoHS) EN 50581:2012

ENGLISH

QUICK GUIDE

ELECTRONIC PRECISION MOISTURE BALANCES

Series: i-Thermo M5

ATTENTION:

This is a guide to start quickly working and do NOT substitute the complete user manual; we

please you to read completely the user manual for a correct installation and a right use of your

new electronic balance.

Usage of the instrument different from the one reported in the user manual does not ensure

anymore the safety of the product.

1. INSTALLATION INSTRUCTIONS

•Remove the balance, the calibration weight (if included) and the accessories from the

package and check if any visible damage of the instrument

•Do not install the balance in places with air flows, heavy thermal changes and vibrations.

Place the support pan and weighing pan on the balance

•Level the balances using the levelling feet and looking at

the level bubble

•

Wait for 30 minutes from switch on and the calibrate the balance (using the appropriate

mass if included) following the instructions of the paragraph “calibration”

Filename:QUICK_GUIDE_BILANCE_M5_EN+IT+POR_rev11;April16

ENGLISH

WARNING

Please follow carefully these steps for installing and use the new balance before

starting your work routine. A way of use of the instrument different from this user

manual will not guarantee the instrument’s safety anymore. Keep this manual in a safe

place.

Please follow these indications to avoid problems and to grant a safe use of

moisture analyzer:

Use the moisture analyzer exclusively for the moisture determination of samples.

Every incorrect use of this instrument may create danger for safety of persons and

may cause damages at the instrument or at other objects.

Do not use the instrument in areas where there is danger of explosions; also make

the instrument work only respecting the enviroment conditions as reported in this

manual.

If this material is used in plants or in enviroment conditions that require strict safety

conditions, please respect the instructions of the directives regarding the installation

of this material currently existing in your country.

This instrument must be used only by qualified personell, who knows the features

and characheristics of the sample under test.

Before starting to work with the instrument for the first time, please check that

voltage is the same of your electric mains.

To get the instrument free from tension, remove the power supply cable.

Place straight the power supply cable so that to avoid contact with the very hot

surfaces of the instrument.

Use only extension cables that are conform to normatives and that are equipped of

a protection conductor.

Attention, protection against heat

Respect the distance and the free space around the instrument to avoid an

accumulation of heat in the instrument and and the over heating of the instrument

ifself:

- 20 cm around the instrument

- 1 m upon the instrument

Do not place flammable materials upon, below or near the instrument since the

heater warms the surroinding area.

Remove the samples carefully, the heater and the dishes for samples may be still

very hot.

Danger for persons or objects when working with particular samples: Fire

Explosion

Flammable or explosive substances

Substances that contain solvents

Substances that during drying emit gas or flammable explosive vapors

ENGLISH

Package content

1 Device for humidity determination.

2 VDE power cable

3 15 pin M/F cable for connecting the

balance/heater

4 Tablemat

5 Sample-holder plate pan

6 Pan with antiventilation cylinder

7 #10 sample-holder plates

8 CD with instruction manual

1 2

Filename:QUICK_GUIDE_BILANCE_M5_EN+IT+POR_rev11;April16

ENGLISH

Start-up

The following describes all the steps required to prepare the device for the first start-up.

Open the oven lid and place:

1. Pan with the antiventilation cylinder

2. Place the sample-holder plate

extractor

3. Place the star on the weighing cone.

The balance is connected to the heater via

a 15-pin M/F cable.

Plug the cable into the two connectors on

the rear of the device as shown in the

figure.

Plug the VDE cable supplied into the

supply connector on the rear of the device.

N.B. Verify that the power supply indicated

on the device nameplate matches the one

in use in the country where you are

installing the unit.

So connect the VDE cable to the outlet in

the vicinity of the device. Do not use

cables/extensions non-compliant with

current regulations.

Wait 30 minutes after the start-up and calibrate the device prior its leveling. For the calibration

procedure, refer to Chapter 7.6. Perform calibration of the device each time it is moved to

another place.

It is recommended not to drop overweight items on the balance weighing pan to avoid

damaging it.

The service must be performed by trained personnel and spare parts used must be original.

To do that, please contact the retailer from whom the device was purchased.

ENGLISH

Display area functions

The thermobalance is equipped with a color display with tap screen functionality that allows

tapping on the screen in the active areas to quickly perform the access to the various menus

and functionality of the device.

Area showing the weighing values or data related to humidity during and at the end of

the drying cycle

g Display of the measurement unit; tapping the symbol, you can access the

menu of the measurement units and select the ones desired.

Stability value display.

T = Tare value display.

0%-100% Analog bar showing the magnitude being measured.

Area showing the heating operation status

60 °C Value display of the heater temperature.

Stb: 60°C Value display of the standby temperature of the heater.

High temperature danger display.

Filename:QUICK_GUIDE_BILANCE_M5_EN+IT+POR_rev11;April16

ENGLISH

Bar to display the time and date, to set the weighing parameters, to select the user, to

access to drying functions and to switch off the device.

By tapping this area, you access the menu of the drying mode functions

By tapping this area, you access the weighting menu settings, the viewing

preferences, the devices and user customization setup

By tapping this area, you access the switching off menu or enable the

standby status of the device

By tapping this area, you access the user menu to make your selection

quickly than desired

Bar to display the function keys.

By tapping the keys displayed in this area, the relative function will be executed. The

following are all available keys that may vary depending on the selected applications

ENGLISH

Standby, logout, switching off functions

After inserting the power cord into the wall outlet, the device will automatically switch on

taking in the basic weighing screen.

By tapping the area with the symbol

You access the switching off menu.

There are 3 switching off modes:

Display off.

Logout.

Switching off.

Display off

Selecting the display off mode, the

device will go in the standby state; the

display is turned off, so that only the

bottom right command to turn on the

system will be enabled.

Tapping the symbol, you will return to the

basic weighing screen.

Logout

Selecting the logout mode, you will

disable the current user

Tapping “Start”, it will activate the user

and in the case of password protected user

it will be asked you to enter it.

Tapping , you can select another

user by which you want to switch on the

device.

Switching off

Selecting the switching off command, the

device will be turned off. To turn it on, you

shall press the key on the left of the device

or remove the power plug and insert it

again.

Filename:QUICK_GUIDE_BILANCE_M5_EN+IT+POR_rev11;April16

ENGLISH

Determination of the humidity content with "Quick" method

This section describes how to perform the analysis of the humidity content using the "Simple"

method that allows you to perform a quick test by defining only the temperature and the

method of drying end.

To access the function, tap the "Simple" icon in the menu "Functions".

The display screen allows you to start a

drying cycle by tapping the "Start" button

with the temperature parameters and

modalities of the drying end displayed to

the right of the function.

Temperature.

Enter the desired temperature and tap the

“OK" key.

The temperature values that can be set

range from a minimum of 35°C to a

maximum of 160°C) with step of 1°C.

Drying end.

The end drying parameter is the setting

that defines the method by which you want

to determine the end of the humidity

measuring cycle contained in the

substance to be analyzed.

ENGLISH

Time: setting this method of the end

drying, the cycle will end when the time set

will be elapsed. Also you can end the cycle

manually at any time by tapping the "Stop"

key.

Enter the value of time and press the "OK"

button to confirm

Autostop %: setting this method of the

end drying, the cycle will end when the

variation of humidity loss will be less than

0.1% for a time interval of 30 seconds.

Also you can end the cycle manually at any

time by tapping the "Stop" key.

Start: tapping “Start”, you will enable the

procedure for the humidity content

analysis.

Load the test pan on the weighing plate

and close the oven. You will automatically

tare the test plate.

Load the substance to analyze and close

the oven.

N.B. The minimum amount of substance

required for the drying cycle based on

the balance resolution:

0.01g Min 500mg

0.001g Min 500mg

0.0001g Min 50mg

Tabla de contenidos

Idiomas:

Otros manuales de Escala de BEL Engineering

BEL Engineering

BEL Engineering HPBG Series Manual de usuario

BEL Engineering

BEL Engineering M5-iDens Manual de usuario

BEL Engineering

BEL Engineering Mark L Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario

BEL Engineering i-Thermo M5 Series Manual de usuario

Manuales populares de Escala de otras marcas