Behringer MonoPoly Manual de usuario

page 1 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

Analog 4-Voice Polyphonic Synthesizer with

37 Full-Size Keys, 4 VCOs, VCF,

2 LFOs, 2 Envelopes, Sync and Cross

Modulation and Arpeggiator

Synthesizers and Samplers

MONOPOLY

Service Support Bulletin

History

Requirement

This calibration function is only available on 1.0.5 or later version rmware.

Date Version Note

2021-03-03 Rev0 Initial version

How to start calibration

Power o MONOPOLY rst.

Long press and hold button HOLD and POLY simultaneously.

page 2 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 2 of 6

Synthesizers and Samplers

MONOPOLY

Cycle power on MONOPOLY.

Wait approximately 2 seconds until power LED blinking slowly.

Release all buttons.

There are 3 sub calibration menus. Press the corresponding button to enter the sub menu.

Tip:

You can only calibrate one channel at a time. Ignore the other channels if you don't want to change them.

Sub Calibration Menu

(Channel) Buttons Function Button LEDs VCO LEDs

1MONO UNISON PITCH WHEEL MAX/MIN indicates PITCH WHEEL position VCO1 LED on

2POLY UNISON PITCH WHEEL dead zone indicates PITCH WHEEL dead zone VCO2 LED on

3POLYPOLY MOD WHEEL MAX/MIN indicates MOD WHEEL position VCO3 LED on

page 3 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 3 of 6

Synthesizers and Samplers

MONOPOLY

Calibration Procedure

Follow all steps in the order they are presented.

Start BEND WHEEL Calibration

Press button MONO UNISON, then VCO1 LED will illuminate.

Calibrate BEND WHEEL maximum position

Move the BEND WHEEL to its maximum position.

page 4 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 4 of 6

Synthesizers and Samplers

MONOPOLY

Calibrate BEND WHEEL minimum position

Move the BEND WHEEL to its minimum position.

Start BEND WHEEL dead zone calibration

This step is to ensure that no bend information is sent while bend wheel is not being touched.

1. Make sure the BEND WHEEL is released and returned to its center position before further operation.

2. Press button POLY UNISON, then VCO2 LED will light up.

page 5 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 5 of 6

Synthesizers and Samplers

MONOPOLY

Start MG1 WHEEL Calibration

Press button POLY POLY, then VCO3 LED will illuminate.

Calibrate MG1 WHEEL maximum position

Move the MG1 WHEEL to its maximum position.

Calibrate BEND WHEEL dead zone

Move the BEND WHEEL within the dead zone where you don't feel the tension of the spring.

page 6 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 6 of 6

Condential, for internal use only. Not to be reproduced.

Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.

Technical specications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik,

Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of

Synthesizers and Samplers

MONOPOLY

End of Procedure

Complete calibration

Short press HOLD + EFFECTS will conrm and save all calibration result. If successful, all BUTTON LEDs will blink at the

same time for a while. Otherwise, it may be a failed calibration.

NOTE: Press HOLD + MONO CHORD will cancel all calibration and return back to normal mode.

Calibrate MG1 WHEEL minimum position

Move the MG1 WHEEL to its minimum position.

Otros manuales para MonoPoly

Tabla de contenidos

Otros manuales de Sintetizador de Behringer

Behringer

Behringer MS-1 Manual de usuario

Behringer

Behringer K-2 Manual de usuario

Behringer

Behringer 2600 Manual de usuario

Behringer

Behringer DEEPMIND 12 Manual de usuario

Behringer

Behringer MS-1-BK Manual

Behringer

Behringer NEUTRON Manual de usuario

Behringer

Behringer FILTAMP MODULE 1006 Manual de usuario

Behringer

Behringer DEEPMIND 12 Manual de usuario

Behringer

Behringer 962 SEQUENTIAL SWITCH Manual de usuario

Behringer

Behringer CRAVE Manual de usuario

Behringer

Behringer UB-Xa Manual de usuario

Behringer

Behringer PRO-1 Manual de usuario

Behringer

Behringer SYSTEM 55 Manual de usuario

Behringer

Behringer 110 VCO/VCF/VCA Manual de usuario

Behringer

Behringer SYSTEM 15 Manual de usuario

Behringer

Behringer Legendary 2500 Series Manual de usuario

Behringer

Behringer CRAVE Instrucciones de instalación

Behringer

Behringer 110 VCO/VCF/VCA Manual de usuario

Behringer

Behringer SYSTEM 55 Manual de usuario

Behringer

Behringer 914 Fixed Filter Bank Manual de usuario

Behringer

Behringer POLY D Instrucciones de instalación

Behringer

Behringer PRO-1 Manual de usuario

Behringer

Behringer D A-440 Instrucciones de instalación

Behringer

Behringer DeepMind 6 Manual de usuario

Manuales populares de Sintetizador de otras marcas

Kawai

Kawai MP7 Manual técnico

Joranalogue

Joranalogue Contour 1 Manual de usuario

Full Bucket Music

Full Bucket Music Mono/Fury Manual de usuario

Kawai

Kawai PH50 Manual de usuario

IK Multimedia

IK Multimedia UNO Synth PRO X Manual de usuario

Roland

Roland Gaia SH-01 Manual de usuario

Roland

Roland GR-30 Manual de usuario

Gotharman

Gotharman Gotharman's anAmoNo-box Manual de usuario

Yamaha

Yamaha DX21 Manual de usuario

QuStream

QuStream HDFS-550 Manual de usuario

Modal Electronics

Modal Electronics ARGON8 Manual de usuario

Roland

Roland GS-500 Manual de usuario

Octave

Octave Cat SRM Manual de usuario

Dreadbox

Dreadbox Murmux Initiate Manual de usuario

neutral labs

neutral labs ELMYRA 2 Manual de usuario

Waldorf

Waldorf KYRA Manual de usuario

Tubbutec

Tubbutec Juno-66 Manual de usuario

EFM

EFM VCADSR - 3510 Manual de usuario