Behringer CAT Guía de referencia

page 1 of 6

985-40000-01170 Rev.A

2021-02-02

Condential, for internal use only. Not to be reproduced.

The unit is carefully calibrated at the factory. The performance may change over time or due to environmental changes,

and the following recalibration procedures can be used to bring it back to its factory settings. If you do not feel comfortable

doing these calibrations, then we recommend they are done by an experienced audio service technician. This is especially true

for those units that need to be opened to gain access to voltage test points and calibration potentiometers.

CAUTION: Incorrect calibration or damage to the delicate adjustment potentiometers may lead to the unit

becoming inoperable.

Note: Although re-calibration will not invalidate the warranty, any damage caused during re-calibration may invalidate

the warranty.

Legendary Duophonic Analog Synthesizer

with Dual VCOs, 4 Mixable Waveforms,

External Signal Processor, 16-Voice Poly Chain,

and Eurorack Format

Synthesizers and Samplers

CAT

User Support Bulletin

Equipment required

1. Small insulated trimmer screwdriver.

2. Small Phillips screwdriver.

3. A at sheet of cardboard or another insulator as wide as the unit. (This will help prevent damage to the top panel when it is

inverted and resting on the bottom chassis).

4. Digital DC Voltmeter with a scale that can display accurately to 0.001 V.

5. Guitar tuner

6. An external MIDI keyboard of at least 6 octaves including A1 and A7.

7. MIDI cable.

8. Pair of headphones or a sound system to monitor the main output.

Important Note:

Leave the unit turned on for approximately 30 minutes. This will allow the circuits time to warm up and the components and

performance to stabilize with temperature. Without this warm-up time, the calibrations will be inaccurate.

Introduction

page 2 of 6

985-40000-01170 Rev.A

2021-02-02

Condential, for internal use only. Not to be reproduced.

page 2 of 6

Turn over the top panel to gain access to the bottom surface of the printed circuit board (pcb). Be careful not to strain

the ribbon cables. Use the cardboard to protect the top panel.

Caution:

Make sure that the circuit board is not touching any bare metal that may cause a short circuit and damage the unit.

Do not touch the circuit board while the unit is powered up.

Remove the 8 screws holding the top panel to the chassis.

Leave the unit turned on for approximately 30 minutes.

Preparation

Remove all cables and connections to the unit.

Carefully connect the power and turn on the synthsizer.

Follow all steps in the order in which they are presented.

Synthesizers and Samplers

CAT

page 3 of 6

985-40000-01170 Rev.A

2021-02-02

Condential, for internal use only. Not to be reproduced.

page 3 of 6

Synthesizers and Samplers

CAT

Oscillator Calibration using a guitar tuner:

The positions of knobs and switches are shown in red on Figure 1.

Connect a guitar tuner to the rear panel main 1/4" output.

Please pay special attention to the FREQUENCY knobs of VCO1 and VCO2.

Note that a pitch within 2 to 3 cents of the target frequency should be ne.

Figure 1

Calibration Procedure

VCO1 Calibration

Turn on the VCO1 SAW fader.

On your external keyboard, press the A2 key and adjust the VCO1 OFFSET trimmer (VR42 on the bottom side) while

observing the guitar tuner display (A2-110Hz) (See gure 2 below).

page 4 of 6

985-40000-01170 Rev.A

2021-02-02

Condential, for internal use only. Not to be reproduced.

page 4 of 6

Synthesizers and Samplers

CAT

VCO2 Calibration

Turn on the VCO2 SAW fader.

On your external keyboard, press the A2 key and adjust the VCO2 OFFSET trimmer (VR44 on the bottom side) while

observing the tuner display (A2-110Hz).

On your external keyboard, press the A5 key and adjust the VCO2 SCALE trimmer (VR43 on the bottom side) while

observing the tuner display (A5-880Hz).

Turn o the VCO1 SAW fader.

Repeat steps 2 and 3 above until both notes are correct in the display. This may need to be repeated several times to

get right.

On your external keyboard, press the A5 key and adjust the VCO1 SCALE trimmer (VR41 on the bottom side) while

observing the tuner display (A5-880Hz).

Figure 2

page 5 of 6

985-40000-01170 Rev.A

2021-02-02

Condential, for internal use only. Not to be reproduced.

page 5 of 6

Synthesizers and Samplers

CAT

OCTAVE Calibration (factory mode)

Set the Digital Voltmeter to measure a range below 10 VDC.

Locate the test points TP20 and GND on the bottom side. Set the position of the front panel OCTAVE SHIFT to -2.

Figure 3

Repeat steps 2 and 3 above until both notes are correct in the display. This may need to be repeated several times to

get right.

Turn o the VCO2 SAW fader.

This calibration is done after the oscillator calibration. The positions of knobs and switches are shown in red on

Figure 1.

page 6 of 6

985-40000-01170 Rev.A

2021-02-02

Condential, for internal use only. Not to be reproduced.

page 6 of 6

Condential, for internal use only. Not to be reproduced.

Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.

Technical specications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik,

Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global

Synthesizers and Samplers

CAT

Connect the negative probe of your voltmeter to GND (shown in gure 3).

Turn o the power and unplug the power connector.

Measure the output voltage. It should read +2.000 V (+/-0.5mV).

Make sure the internal connections are still correctly inserted and secured.

If not, then adjust the OCT ADJ potentiometer (VR45) until the measured output voltage is +2.000 V (+/-0.5mV).

Ret the top panel back into the bottom chassis and secure with all the screws.

This calibration is done after the oscillator calibration. The positions of knobs and switches are shown in red on Figure 1.

Connect a guitar tuner to the rear panel main 1/4" output.

OCTAVE Calibration (user mode)

Turn on the VCO1 SAW fader.

Set the position of the front panel OCTAVE SHIFT to -2. On your external keyboard, press the A4 key and adjust the

FREQUENCY knobs of VCO1 while observing the tuner display (A4 with OCTAVE SHIFT at -2: 110Hz).

Set the position of OCTAVE SHIFT to +2, observe the tuner display (A4 with OCTAVE SHIFT at +2: 1760Hz). If not, then

adjust the OCT ADJ potentiometer (VR45 on the bottom side) until the frequency is correct.

End of Procedure

Connect the positive probe of your voltmeter to TP20 (shown in gure 3).

Tabla de contenidos

Otros manuales de Sintetizador de Behringer

Behringer

Behringer CRAVE Manual de usuario

Behringer

Behringer PRO-VS MINI Manual de usuario

Behringer

Behringer 2600 Manual de usuario

Behringer

Behringer PRO-VS MINI Manual de usuario

Behringer

Behringer UB-Xa Manual de usuario

Behringer

Behringer SYSTEM 100 172 PHASE SHIFTER/DELAY/LFO Manual de usuario

Behringer

Behringer TORO Manual de usuario

Behringer

Behringer 112 DUAL VCO Manual de usuario

Behringer

Behringer MonoPoly Instrucciones de instalación

Behringer

Behringer POLY D Manual de usuario

Behringer

Behringer DeepMind 6 Manual de usuario

Behringer

Behringer VOCODER VC340 Manual de usuario

Behringer

Behringer 110 VCO/VCF/VCA Manual de usuario

Behringer

Behringer CRAVE Instrucciones de instalación

Behringer

Behringer CRAVE Manual de usuario

Behringer

Behringer MS-1 Manual de usuario

Behringer

Behringer TD-3 Manual de usuario

Behringer

Behringer EDGE Manual de usuario

Behringer

Behringer DEEPMIND 12 Manual de usuario

Behringer

Behringer POLY D Instrucciones de instalación

Behringer

Behringer MS-1-BK Manual

Behringer

Behringer ODYSSEY Manual de usuario

Behringer

Behringer 2600 Manual de usuario

Behringer

Behringer K-2 Manual de usuario

Manuales populares de Sintetizador de otras marcas

Kawai

Kawai MP7 Manual técnico

Joranalogue

Joranalogue Contour 1 Manual de usuario

Full Bucket Music

Full Bucket Music Mono/Fury Manual de usuario

Kawai

Kawai PH50 Manual de usuario

IK Multimedia

IK Multimedia UNO Synth PRO X Manual de usuario

Roland

Roland Gaia SH-01 Manual de usuario

Roland

Roland GR-30 Manual de usuario

Gotharman

Gotharman Gotharman's anAmoNo-box Manual de usuario

Yamaha

Yamaha DX21 Manual de usuario

QuStream

QuStream HDFS-550 Manual de usuario

Modal Electronics

Modal Electronics ARGON8 Manual de usuario

Roland

Roland GS-500 Manual de usuario

Octave

Octave Cat SRM Manual de usuario

Dreadbox

Dreadbox Murmux Initiate Manual de usuario

neutral labs

neutral labs ELMYRA 2 Manual de usuario

Waldorf

Waldorf KYRA Manual de usuario

Tubbutec

Tubbutec Juno-66 Manual de usuario

EFM

EFM VCADSR - 3510 Manual de usuario