Behringer 961 Interface Manual de usuario

Quick Start Guide

961 INTERFACE

Legendary Analog Multi-channel

Trigger Converter Module for Eurorack

Controls

(1) AUDIO IN – Use this 3.5 mm jack to route an audio

signal into the module for conversion to a V-Trig

(voltage trigger) signal. The audio signal passes through

the SENSITIVITY control before being converted, and the

nal, converted signal then exits the module at the V-TRIG

OUT parallel connections immediately to the right of the

SENSITIVITY knob.

(2) SENSITIVITY – Use this knob to adjust the gain of the

audio signal coming into the module through the AUDIO

IN jack. Rotate the knob until you nd a setting that gives

you the best audio-to-voltage conversion.

(3) V-TRIG OUT – Use the parallel jacks to route the converted

audio-to-voltage V-Trig signal back out of the module via

cables with 3.5 mm TS connectors.

(4) S-TRIG IN – Route S-Trig (switch trigger) control signals

into the module via cables with 3.5 mm TS connectors

for conversion to V-Trig (voltage trigger) signals.

The converted V-Trig signal comes back out of the

module via the parallel V-TRIG OUT jacks immediately

to the right of the S-TRIG IN jack.

(5) V-TRIG OUT – Use these parallel jacks to send the

converted V-Trig signal back out of the module via cables

with 3.5 mm TS connectors.

(6) V-TRIG IN A/B – Use these rows of 3.5 mm jacks to route

in multiple V-Trig (voltage trigger) signals for conversion

to an S-Trig (switch trigger) signal that exits the module

via the S-TRIG OUT jack assigned to this section of the

module. The V-TRIG IN A row of inputs go straight to

conversion and output, while the V-TRIG IN B row of

inputs pass through the SWITCH-ON TIME control before

being combined with the converted A signal for nal

output through the S-TRIG OUT jack. When any valid

V-TRIG input activates the S-TRIG output, any other V-TRIG

input activity will be ignored until the rst V-TRIG cycle

has ended.

(7) SWITCH-ON TIME – Use this knob to manually limit or

extend the “ON” time duration of V-Trig signals coming in

through the V-TRIG IN B row of input jacks. The “ON” time

can be varied from 40 milliseconds to a full 4 seconds.

(8) S-TRIG OUT – This jack routes the nal S-Trig signal from

the V-TRIG IN A/B jacks back out of the module via cables

with 3.5 mm TS connectors.

Power Connection

The 961 INTERFACE module comes with the required power cable

for connecting to a standard Eurorack power supply system.

Follow these steps to connect power to the module. It is easier to

make these connections before the module has been mounted

into a rack case.

1. Turn the power supply or rack case power o and

disconnect the power cable.

2. Insert the 16-pin connector on the power cable into the

socket on the power supply or rack case. The connector has

a tab that will align with the gap in the socket, so it cannot

be inserted incorrectly. If the power supply does not have

a keyed socket, be sure to orient pin 1 (-12 V) with the red

stripe on the cable.

3. Insert the 10-pin connector into the socket on the back of

the module. The connector has a tab that will align with the

socket for correct orientation.

4. After both ends of the power cable have been securely

attached, you may mount the module in a case and turn on

the power supply.

(1) (2) (4)

(5)

(7)

(6)

(8)

(3)

Installation

The necessary screws are included with the module for mounting

in a Eurorack case. Connect the power cable before mounting.

Depending on the rack case, there may be a series of xed holes

spaced 2 HP apart along the length of the case, or a track that

allows individual threaded plates to slide along the length

of the case. The free-moving threaded plates allow precise

positioning of the module, but each plate should be positioned in

the approximate relation to the mounting holes in your module

before attaching the screws.

Hold the module against the Eurorack rails so that each of the

mounting holes are aligned with a threaded rail or threaded

plate. Attach the screws part way to start, which will allow small

adjustments to the positioning while you get them all aligned.

After the nal position has been established, tighten the

screws down.

Specications

Signal Connections

Audio-to-voltage-trigger

converter

1 x circuit

Audio in 1 x 3.5 mm jack, AC coupled

Input impedance > 3 kΩ unbalanced

V-trig out 2 x 3.5 mm parallel jacks,

DC coupled

Output Impedance < 2 kΩ, unbalanced

Maximum output level +5 V

Switch-to-voltage-trigger

converter

2 x circuit (left and right)

S-trig in 1 x 3.5 mm jack, DC coupled

Operation Pull low to trigger

Maximum input level +12 V

V-trig out 2 x 3.5 mm parallel jacks,

DC coupled

Output Impedance < 2 kΩ, unbalanced

Maximum output level +5 V

Voltage-to-switch-trigger

converter

2 x circuit (left and right)

V-trig in A 6 x 3.5 mm jacks,

DC coupled

Input Impedance 10 kΩ, unbalanced

Maximum input level +5 V

Minimum level to trigger + 1.5 V

V-trig in B 6 x 3.5 mm jacks,

AC coupled

Input Impedance 10 kΩ unbalanced

Maximum input level +5 V

Minimum level to trigger + 1.5 V

S-trig out 1 x 3.5 mm jack, DC coupled

Operation Active low

Output level 0 V to +12 V pullup resistor

Controls

Sensitivity 1 x rotary knob

Switch-on time 2 x rotary knob

40 ms to 4 s, adjustable

Power

Power supply Eurorack

Current draw 50 mA (+12 V)

Physical

Dimensions 35 x 106 x 129 mm

(1.4 x 4.2 x 5.1")

Rack units 21 HP

Weight 0.22 kg (0.49 lbs)

LEGAL DISCLAIMER

Music Tribe accepts no liability for any loss which may be suered by any

person who relies either wholly or in part upon any description, photograph,

or statement contained herein. Technical specications, appearances and

other information are subject to change without notice. All trademarks are the

property of their respective owners. Midas, KlarkTeknik, Lab Gruppen, Lake,

Tannoy,Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone

and Coolaudio are trademarks or registered trademarks of MusicTribe

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information

regarding MusicTribe’s Limited Warranty, please see complete details online

at musictribe.com/warranty.

Zhongshan Eurotec Electronics Limited

No. 10 Wanmei Road, South China Modern Chinese Medicine Park,

Nanlang Town, 528451, Zhongshan City, Guangdong Province, China

Otros manuales para 961 Interface

Tabla de contenidos

Otros manuales de Unidad de control de Behringer

Behringer

Behringer 992 CONTROL VOLTAGES Manual de usuario

Behringer

Behringer 921A Oscillator Driver Manual de usuario

Behringer

Behringer 150 RING MOD/NOISE/S&H/LFO Manual de usuario

Behringer

Behringer 960 SEQUENTIAL CONTROLLER Manual de usuario

Behringer

Behringer 1027 Manual de usuario

Behringer

Behringer 902 Manual de usuario

Behringer

Behringer 992 CONTROL VOLTAGES Manual de usuario

Behringer

Behringer 923 FILTERS Manual de usuario

Behringer

Behringer MODAMP 2500 Series Manual de usuario

Behringer

Behringer 2500 Series Manual de usuario

Behringer

Behringer MIX-SEQUENCER MODULE 1050 Manual de usuario

Behringer

Behringer 2500 Series Manual de usuario

Behringer

Behringer 173 QUAD GATE/MULTIPLES Manual de usuario

Behringer

Behringer 140 DUAL ENVELOPE/ LFO Manual de usuario

Behringer

Behringer 921B OSCILLATOR Manual de usuario

Behringer

Behringer DUAL ENVELOPE GENERATOR MODULE 1003 Manual de usuario

Behringer

Behringer 994 MULTIPLES Manual de usuario

Behringer

Behringer CP35 Attenuators Manual de usuario

Behringer

Behringer 121 DUAL VCF Manual de usuario

Behringer

Behringer BRAINS Manual de usuario

Behringer

Behringer CP3A-O Manual de usuario

Behringer

Behringer 112 DUAL VCO Manual de usuario

Behringer

Behringer 2500 Series Manual de usuario

Behringer

Behringer 130 DUAL VCA Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario