Becom Argos3D-Pulse Manual de usuario

Argos3D-Pulse

Quick Start Guide

Version 2

Quick Start Guide - Argos3D-Pulse

Last change: 1 October 2021/Version 2

2| 11

BECOM Systems GmbH

Gutheil-Schoder-Gasse 17

1230 Wien

AUSTRIA

office.systems@becom-group.com

systems.becom-group.com

Argos3D-Pulse –Quick Start Guide

Document No.: 900-308 / A

Publication date: October 1, 2021

Subject to change without notice. Errors excepted.

for any purpose in any form or by any means, electronically or mechanically, without expressly written permission by

BECOM Systems.

Windows is a registered trademark of Microsoft.

Quick Start Guide - Argos3D-Pulse

Last change: 1 October 2021/Version 2

3| 11

Table of Contents

1Unboxing.......................................................................................................................................................................................................................5

1.1 In the box................................................................................................................................................................................................................5

1.2 Connecting your Argos3D-Pulse.......................................................................................................................................................5

1.3 Connector Overview.................................................................................................................................................................................5

1.3.1 Connecting the break-out board................................................................................................................................................6

1.3.2 Connecting the power supply ......................................................................................................................................................6

1.3.3 Connecting the Ethernet Cable ...................................................................................................................................................7

2Evaluation Software .............................................................................................................................................................................................8

2.1 Prepare your Network Interface Card (NIC)..............................................................................................................................8

2.2 Start using your Argos3D-Pulse with ‘BltTofSuite’...............................................................................................................8

3System Requirements & Support................................................................................................................................................................9

3.1 Support...............................................................................................................................................................................................................9

4Document Revision History...........................................................................................................................................................................10

AList of Figures and Tables.................................................................................................................................................................................11

Quick Start Guide - Argos3D-Pulse

Last change: 1 October 2021/Version 2

4| 11

The information herein is given to describe certain components and shall not be considered as a guarantee of

characteristics.

Terms of delivery and rights of technical change reserved.

We hereby disclaim any warranties, including but not limited to warranties of non-infringement, regarding circuits,

descriptions and charts stated herein.

BECOM Systems makes and you receive no warranties or conditions, express, implied, statutory or in any communication

with you. BECOM Systems specifically disclaims any implied warranty of merchantability or fitness for a particular purpose.

BECOM Systems takes no liability for any damages and errors causing of the usage of this board. The user of this board is

responsible by himself for the functionality of his application. He is allowed to use the board only if he has the

qualification. More information is found in the General Terms and Conditions (AGB).

Information

For further information on technology, delivery terms and conditions and prices please contact BECOM Systems

www.becom-group.com

Warning

Due to technical requirements components may contain dangerous substances.

5| 11

Quick Start Guide - Argos3D-Pulse

Last change: 1 October 2021/Version 2

1Unboxing

1.1 In the box

•Argos3D-Pulse

•CAT5/7 Ethernet Cable

•Interface Breakout-Board

•Quick Start Guide

•Power Supply

Note

The power supply’s operating temperature is specified from 0 to +40°C. This represents not

the effective working temperature of the Argos3D-Pulse sensor!

1.2 Connecting your Argos3D-Pulse

1.3 Connector Overview

The Argos3D-Pulse uses one common connector for power and interfaces. For test purposes the KIT contains a

breakout-board to have individual access to the interfaces of the Argos3D-Pulse.

The break-outboard has three main interfaces:

a. Power Connector

b. Ethernet

c. Argos3D-Pulse common connector

Figure 1-1: Argos3D-Pulse break-out board front and rear view

6| 11

Quick Start Guide - Argos3D-Pulse

Last change: 1 October 2021/Version 2

Note

Please follow the next steps in the right order to get your ‘Argos3D-Pulse’up and running

correctly.

1.3.1 Connecting the break-out board

Please connect the break-out board to the Argos3D-Pulse common connector first.

Figure 1-2: Argos3D-Pulse common connector

1.3.2 Connecting the power supply

To ensure, that your Argos3D-Pulse works correctly, connect the ‘Argos3D’ to a 12-30V DC power supply using

connector (a) and wait for approximately 20 seconds until the camera boots up.

Pin assignment on the power connector (a): Pin #1: +12V to +30V, Pin#2: GND

Note

The power supply connector is protected against wrong polarity but the ‘Argos3D’ will not

work in case you don’t use the correct polarity! If the Argos3D-Pulse doesn’t work please

check the power supply polarity first!

7| 11

Quick Start Guide - Argos3D-Pulse

Last change: 1 October 2021/Version 2

1.3.3 Connecting the Ethernet Cable

Plug in the Ethernet cable (b) and connect your Argos3D-Pulse to your PC.

Figure 1-3: Argos3D-Pulse connected to power and Ethernet

8| 11

Quick Start Guide - Argos3D-Pulse

Last change: 1 October 2021/Version 2

2Evaluation Software

Please open the website at support.systems.becom-group.com and select “Support, Documentation & Software

Download”. Please select the Argos3D-Pulse product link and download the Blt Tof Suite.

2.1 Prepare your Network Interface Card (NIC)

Once you have connected your Argos3D-Pulse to a Network Interface Card (NIC) of your PC give this NIC the IP-

Address 192.168.0.1 with a subnet mask of 255.255.255.0.

No driver must be installed on your PC!

The Argos3D-Pulse uses IP-Address 192.168.0.10 with subnet mask 255.255.255.0.

2.2 Start using your Argos3D-Pulse with ‘BltTofSuite’

Using this software, you can simply display the depth image, the pointcloud and the amplitude image of the

Argos3D-Pulse. For a detailed introduction to the software, please read the ‘ToF Suite - Quick Start Guide’

Go to the directory where you unzipped the software and start the “

BltTofSuite.exe

”. On how to use the ToF

Suite, please refer to the user manual.

9| 11

Quick Start Guide - Argos3D-Pulse

Last change: 1 October 2021/Version 2

3System Requirements & Support

An Argos3D-Pulse enabled application is required in order to use this ‘Argos3D’ device.

Connect to a system with:

•Operating System: Microsoft Windows 7/8/10

•32 bit (x68) or 64 bit (x64) processor

•Dual-core 2 GHz or faster CPU

•Dedicated Ethernet port

•4 GByte RAM

3.1 Support

For answers to common questions, troubleshooting steps and further documentation visit our BECOM Systems

support website or using the direct link: https://support.bluetechnix.com/wiki/Main_Page

10 | 11

Quick Start Guide - Argos3D-Pulse

Last change: 1 October 2021/Version 2

4Document Revision History

Version

Date

Document Revision

2021 08 02

First draft

2021 10 01

Review, minor changes and release

Table 4-1: Revision history

Otros manuales para Argos3D-Pulse

Tabla de contenidos

Otros manuales de Accesorios de Becom

Becom

Becom TOREO-P650 Manual de usuario

Becom

Becom TOREO-P650 Instrucciones de uso

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario