Beckhoff CX2500-0061 Manual de usuario

Manual

CX2500-0061

Power over Ethernet (PoE) module

1.0

2016-07-13

Version:

Date:

Table of contents

1 Foreword ....................................................................................................................................................4

1.1 Notes on the documentation............................................................................................................. 4

1.2 Safety instructions ............................................................................................................................ 5

1.3 Documentation issue status.............................................................................................................. 5

2 Product overview.......................................................................................................................................6

2.1 Intended use ..................................................................................................................................... 6

2.2 System overview............................................................................................................................... 7

2.3 CX2500-0061 - Technical data ......................................................................................................... 8

3 Unpacking and transport ..........................................................................................................................9

4 Mounting and wiring ...............................................................................................................................10

4.1 Installing at the CX20x0 system ..................................................................................................... 10

4.2 Installing the bar clips ..................................................................................................................... 12

4.3 Installation on the mounting rail ...................................................................................................... 13

4.4 Ethernet interface (X610)................................................................................................................ 16

5 Error handling and diagnostics .............................................................................................................17

5.1 Diagnostic LEDs ............................................................................................................................. 17

5.2 Faults .............................................................................................................................................. 18

6 Removal and disposal.............................................................................................................................19

7 Appendix ..................................................................................................................................................21

7.1 Certifications ................................................................................................................................... 21

7.2 Support and Service ....................................................................................................................... 22

CX2500-0061 3Version: 1.0

Foreword

1 Foreword

1.1 Notes on the documentation

This description is only intended for the use of trained specialists in control and automation engineering who

are familiar with the applicable national standards.

It is essential that the following notes and explanations are followed when installing and commissioning

these components.

The responsible staff must ensure that the application or use of the products described satisfy all the

requirements for safety, including all the relevant laws, regulations, guidelines and standards.

Disclaimer

The documentation has been prepared with care. The products described are, however, constantly under

development.

For that reason the documentation is not in every case checked for consistency with performance data,

standards or other characteristics.

In the event that it contains technical or editorial errors, we retain the right to make alterations at any time

and without warning.

No claims for the modification of products that have already been supplied may be made on the basis of the

data, diagrams and descriptions in this documentation.

Trademarks

Beckhoff®, TwinCAT®, EtherCAT®, Safety over EtherCAT®, TwinSAFE®, XFC®and XTS® are registered

trademarks of and licensed by Beckhoff Automation GmbH.

Other designations used in this publication may be trademarks whose use by third parties for their own

purposes could violate the rights of the owners.

Patent Pending

The EtherCAT Technology is covered, including but not limited to the following patent applications and

patents:

EP1590927, EP1789857, DE102004044764, DE102007017835

with corresponding applications or registrations in various other countries.

The TwinCAT Technology is covered, including but not limited to the following patent applications and

patents:

EP0851348, US6167425 with corresponding applications or registrations in various other countries.

EtherCAT® is registered trademark and patented technology, licensed by Beckhoff Automation GmbH,

Germany

The reproduction, distribution and utilization of this document as well as the communication of its contents to

others without express authorization are prohibited.

patent, utility model or design.

CX2500-00614 Version: 1.0

Foreword

1.2 Safety instructions

Safety regulations

Please note the following safety instructions and explanations!

Product-specific safety instructions can be found on following pages or in the areas mounting, wiring,

commissioning etc.

Exclusion of liability

All the components are supplied in particular hardware and software configurations appropriate for the

application. Modifications to hardware or software configurations other than those described in the

documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG.

Personnel qualification

This description is only intended for trained specialists in control, automation and drive engineering who are

familiar with the applicable national standards.

Description of symbols

In this documentation the following symbols are used with an accompanying safety instruction or note. The

safety instructions must be read carefully and followed without fail!

DANGER

Serious risk of injury!

Failure to follow the safety instructions associated with this symbol directly endangers the

life and health of persons.

WARNING

Risk of injury!

Failure to follow the safety instructions associated with this symbol endangers the life and

health of persons.

CAUTION

Personal injuries!

Failure to follow the safety instructions associated with this symbol can lead to injuries to

persons.

Attention

Damage to the environment or devices

Failure to follow the instructions associated with this symbol can lead to damage to the en-

vironment or equipment.

Note

Tip or pointer

This symbol indicates information that contributes to better understanding.

1.3 Documentation issue status

Version Changes

1.0 First version

CX2500-0061 5Version: 1.0

Product overview

2 Product overview

2.1 Intended use

The CX20x0 device series is a modular control system designed for DIN rail installation. The system is

scalable, so that the required modules can be assembled and installed in the control cabinet or terminal box

as required.

Only switch the PC off after closing the software

Before the Embedded PC is switched off, the software currently running on it should be stopped properly in

order to avoid data loss on the hard disk. Please read the section on “Switching off”.

Switch off all system components and uncouple the Industrial PC from the system if the PC is not used for

control purposes, e.g. during a function test. To disconnect first pull the first terminal behind the power

supply unit (optional), then pull the connectors of the fieldbus connections.

System components that have been switched off must be secured against being switched on again.

The Embedded PC’s power supply unit must be supplied with 24VDC.

Attention

Damage to the environment or devices

Do not exchange any parts when under power! The exchange of controller parts when live

can lead to short-circuits or overvoltages. These can damage the controller itself and con-

nected peripherals (terminals, monitors, input devices, etc.).

When components are being fitted or removed, the supply voltage must be switched off.

Software knowledge

Attention

System malfunctions

Mandatory software knowledge! Every user must be familiar with any of the functions of the

software installed on the PC that he can reach.

CX2500-00616 Version: 1.0

Product overview

2.2 System overview

The system modules for the CX2000 family are connected to the CPU on the left-hand side via a multi-pin

connector. Internally they are connected via PCI Express. Up to four modules can be connected in any

order.

The CX2500-0020 audio module has jack plug (5 x 3.5 mm) and cinch plug for digital signals (SPDIF). Up to

7.1 multi-channel audio can be used. Serial interfaces can be added with the modules CX2500-0030

(RS232) and CX2500-0031 (RS422/RS485). The CX2500-0060 module provides two further independent

Gbit Ethernet interfaces. The CX2500-0070 module can be used to add up to four further USB 3.0 interfaces.

Power over Ethernet (PoE) module CX2500-0061

The CX2500-0061 Power over Ethernet module supports devices with PoE class 0, 1, 2, 3 and 4 in

accordance with the PoE standard IEEE 802.3af-2003. The maximum PoE power output is 15.4 W. The PoE

supply voltage is generated internally, no external power supply is necessary. In the case of an overload of

the CX2500-0061, the PoE supply shuts down for two seconds, then restarts. The diagnostic LEDs PWR,

PoE, PM1 and PM2 provide information about the type of PoE supply (mode A or B) as well as about the

PoE class reported by the powered device.

CX2500-0061 7Version: 1.0

Product overview

2.3 CX2500-0061 - Technical data

Dimensions

The system module CX2500-0061 provides a further Power over Ethernet (PoE) interface for the CX20x0.

Technical data CX2500-0061

Interfaces 1 x RJ45, 10/100/1000 MBit/s with Power-over-Ethernet (PoE)

max. PoE power delivery 15,4 W

Supported devices Devices of PoE Class 0, 1, 2, 3 and 4 as defined by PoE standard IEEE

802.3af-2003

Power supply via system bus (through CX2100-0xxx power supply modules)

internal generation of PoE supply voltage (no external 48 V power feeding

required)

max. Power loss 3 W

Dielectric strength 500 V (supply / internal electronics)

Dimensions (W x H x D) 24 mm x 99 mm x 54,5 mm

Weight approx. 208 g

Operating/storage temperature -25° C ... +60° C / -40° C ... +85° C

Relative humidity 95 %, no condensation

Vibration/shock resistance conforms to EN 60068-2-6/EN 60068-2-27

EMC immunity/emission conforms to EN 61000-6-2/EN 61000-6-4

Protection class IP 20

Further Information: www.beckhoff.de/CX2000

CX2500-00618 Version: 1.0

Unpacking and transport

3 Unpacking and transport

Note

Short circuit due to moisture

Moisture can lead to short circuits. Moisture can form during transport in cold weather or in

the event of large temperature fluctuations.

Avoid moisture formation (condensation) in the device, and leave the device to adjust to

room temperature slowly. If condensation has occurred, wait at least 12 hours before

switching on the device.

Proceed as follows to unpack the unit:

1. Remove packaging.

2. Do not discard the original packaging. Keep it for transporting the device in the future.

3. Check the delivery for completeness by comparing it with your order.

4. Please keep the associated paperwork. It contains important information for handling the unit.

5. Check the contents for visible shipping damage.

6. If you notice any shipping damage or inconsistencies between the contents and your order, you should

notify Beckhoff Service.

Shipping and relocation

Despite the robust design of the unit, the components are sensitive to strong vibrations and impacts.

Therefore, during transport please protect your device from:

• mechanical stress and

• use the original packaging.

Follow the specified storage conditions for the device and store it at temperatures between -40 °C and +85

°C.

CX2500-0061 9Version: 1.0

Mounting and wiring

4 Mounting and wiring

4.1 Installing at the CX20x0 system

Note

Damage to the contacts

Incorrect installation may result in damage to the contacts of the system modules.

The system modules may only be attached on the left-hand side of the basic CPU module.

A maximum of four system modules can be attached to the basic CPU module via the internal PCI Express

bus. In delivery state the system module is equipped with a protective cap for the bus connector.

Before continuing, connect the system module to the basic CPU module.

Prerequisites for this step:

• Exit the software and shut down the CX20x0 hardware configuration.

• Switch off the power supply.

Install the system module as follows:

1. Put a screwdriver into the recess on the short side of the protective cap and lever it off.

2. Remove the protective cap to expose the bus connector.

3. Insert the system module on the left-hand side of the basic CPU module.

CX2500-006110 Version: 1.0

Tabla de contenidos

Otros manuales de Unidad de control de Beckhoff

Beckhoff

Beckhoff EM2042 Manual del operador

Beckhoff

Beckhoff CX2550-0020 Manual de usuario

Beckhoff

Beckhoff EJ40 Series Manual del operador

Beckhoff

Beckhoff EP1 Series Manual del operador

Beckhoff

Beckhoff C9900-M900 Guía del usuario

Beckhoff

Beckhoff EP3204 Manual del operador

Beckhoff

Beckhoff KM2002 Manual del operador

Beckhoff

Beckhoff EJ7211-0010 Manual del operador

Beckhoff

Beckhoff KM10 2 Series Manual del operador

Beckhoff

Beckhoff EJ6910 Manual de usuario

Beckhoff

Beckhoff M1400 Guía

Beckhoff

Beckhoff C9900-M800 Manual de usuario

Beckhoff

Beckhoff KM4602 Manual del operador

Beckhoff

Beckhoff AX2090-MD50 Series Manual del operador

Beckhoff

Beckhoff EP31 Series Manual del operador

Beckhoff

Beckhoff BK5200 Guía

Beckhoff

Beckhoff EPP3174 Manual del operador

Beckhoff

Beckhoff EP7211-0034 Manual del operador

Beckhoff

Beckhoff PS9031-4820-0001 Manual del operador

Beckhoff

Beckhoff KL85 Series Manual del operador

Beckhoff

Beckhoff EP7041 Series Manual del operador

Beckhoff

Beckhoff CX2550-0010 Manual de usuario

Beckhoff

Beckhoff M2510 Manual de lista de piezas

Beckhoff

Beckhoff AX5801 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario