BC Biomedical MAXISIM 2000 Manual de usuario

User Manual

MAXISIM 2000

Patient Simulator

CONTENTS

I. MANUAL REVISION RECORD .................................2

II. INTRODUCTION....................................................... 3

III. SPECIFICATIONS .................................................... 4

IV. RECEIPT, INSPECTION & RETURN......................... 6

V. CONTROL SWITCHES AND TERMINALS................ 7

VI. WARRANTY ........................................................... 10

VI. TECHNICAL SUPPORT.......................................... 10

I. MANUAL REVISION RECORD

This record page is for recording revisions to your MAXISIM 2000 User Manual that have been published

by BC Biomedical or its authorized representatives. We recommend that only the management or facility

representative authorized to process changes and revisions to publications:

•Make the pen changes or insert the revised pages;

•Ensure that obsolete pages are withdrawn and either disposed of immediately, or marked as

superseded and placed in a superseded document file, and;

•Enter the information below reflecting that the revisions have been entered.

Rev No Date Entered Reason Signature of Person Entering Change

0 - Initial Release

1.1 4-16-04 Adding CPV on Pg. 4 KB

II. INTRODUCTION

BC Biomedical’s MaxiSim 2000 is a high performance simulator designed to simplify patient monitor

testing, and is designed to be used by trained service technicians. It simulates electrocardiogram,

respiration, dynamic blood pressure and static temperature.

It offers three preprogrammed automatic test modes (ECG rate, ECG performance rate, and BP level),

plus a built-in ECG lead continuity test. Arrhythmia selection includes two supraventricular, two-

conduction; eight ventricular,

one paced; and one fetal/maternal ECG simulation.

General MaxiSim 2000 Information:

Display/Control: 2-digit numeric display keys

5 switches for BP, respiration, temperature

and Power On/Off

ECG Output Connectors

High Level: Standard phone jack

Low level: 10 AHA color-coded standard safety banana

connectors with detachable banana to snap

adapter.

Power: 9 V Alkaline battery or battery eliminator

Case: High impact plastic

Weight: 0.5 kg / 1.1 lbs.

Dimensions: Height: 47 mm / 1.8 in.

Width: 138 mm / 5.4 in.

Length: 190 mm / 7.5 in.

Standard Accessories: MaxiSim 2000 Patient Simulator

Carrying Case

Snap-to-Banana Adapters (10pk)

User Manual MaxiSim 2000

Optional Accessories: Unterminated or prewired BP Cable

Unterminated or prewired 400/700

YSI-series Temperature Cable

110 V or 220 V AC Adapter

III. SPECIFICATIONS

ECG General

Lead Configuration: 12-lead simulation derived from one resistively

divided analog signal.

RL, RA, LA, LL, V1-6

Output Impedance

Limb leads: 500 or 1000 ohms to RL

V Leads: 1000 ohms to RL

High Level Output: 0.5 V/mV of low level (Lead II)

Normal Sinus

Rates: 30, 60, 80, 120, 180, and 300 BPM

Rate Accuracy: ± 1% of selection

Amplitudes: 0.5mV, 1.0mV, 1.5mV and 2.0mV (Lead II)

Amplitude Accuracy: ± 5%. (Lead II 1.0mV)

Automatic ECG Rate Test

Manual ECG Performance Test

Square Wave: 2.0Hz 1.0 V p-p biphasic

DC pulse: 4.0 sec. 1.0 mV

Sine Waves: 0.1, 0.5, 10, 40, 50, 60 and 100 Hz

Triangle Wave: 2.0 Hz

Amplitude: 0.5mV, 1.0mV, 1.5mV and 2.0mV (Lead II)

Amplitude Accuracy: ± 5%. (Lead II 1.0mV)

Automatic ECG Performance Test

Gain/Damping: 2 Hz square wave

Frequency Response

Low Frequency: 4 second DC pulse

Band Pass: 10 Hz sine

Monitor: -3dB point: 40 Hz sine

Power Li ne Notch Filter: 50 Hz sine

Linearity: 2 Hz triangle wave

ECG Lead Test

Display flashes if lead resistance is <3 kOhms (DC lead wire only)

Blood Pressure General

Input/Output Impedance: 300 Ohms

Exciter Voltage Range: 2 to 16 volts

Exciter Frequency Range: DC to 4000 Hz

Output Sensitivity: 5 or 40 µV/V/mmHg

Accuracy: ± 1% full scale ± 1 mmHg

Calibrated Rate: 80 BPM

Dynamic Blood Pressure Selections

Arterial: 120/80 mmHg

Left Ventricle: 20/0 mmHg

Right Ventricle: 25/0 mmHg

Pulmonary Artery: 25/10 mmHg

CVP (Central Venous Pressure): 15/10 mmHg

PAW (Pulmonary Wedge): 10/2 mmHg

Static Levels: 0, 20, 40, 80, 100, 200, 250, 300 mmHg

Arrhythmia Selections

Atrial Fibrillation 1 & 2

Premature Atrial Contraction

Premature Ventricular Contraction (PVC)

Early PVC

R on T PVC

Multifocal PVCs

Bigeminy

Bigeminy Run of 5 PVCs

Ventricular Tachycardia

Ventricular Fibrillation

Second Degree Type 2

Right Bundle Branch Block

Asynchronous Pacemaker

Fetal/Maternal ECG

Respiration

Normal Physiological Simulation

Baseline Impedances: 500 to 1000 Ohms

Impedance Variations: 0.1, 0.2, 0.5, 1.0, and 3.0 Ohms

Rates: 0 (Apnea), 15, 20, 30, 40, 60, 120 BPM

Output Configuration: Lead 1, 11, RL-LL

Temperature

30°C / 86°F, 37°C / 98.6°F, 40°C / 104°F

Compatible with YSI 400/700 series

Accuracy: ± 0.25°C

IV. RECEIPT, INSPECTION & RETURN

1. Inspect the outer box for damage.

2. Carefully unpack all items from the box and check to see that you have the following items:

•MaxiSim 2000 Patient Simulator

•Carrying Case

•10 Pack, Snap-to-Banana Adapters

•MaxiSim 2000 User Manual

3. If you note physical damage, or if the unit fails to function according to specification, inform the

supplier immediately. When BC Biomedical or the company’s representative, is informed, measures

will be taken to either repair the unit or dispatch a replacement. The customer will not have to wait for

a claim to be investigated by the supplier. The customer should place a new purchase order to ensure

delivery.

4. When returning an instrument to BC Biomedical, or the company representative, fill out the address

label, describe what is wrong with the instrument, and provide the model and serial numbers. If

possible, use the original packaging material for return shipping. Otherwise, repack the unit using:

•A reinforced cardboard box, strong enough to carry the weight of the unit.

•At least 5 cm of shock-absorbing material around the unit.

•Nonabrasive dust-free material for the other parts.

Repack the unit in a manner to ensure that it cannot shift in the box during shipment.

BC Biomedical’s product warranty is on page 8 of this manual. The warranty does not cover freight

charges. C.O.D. will not be accepted without authorization from BC Biomedical or its representative.

V. CONTROL SWITCHES AND TERMINALS

Front Panel

1. Power Switch Turns the power on and off.

2. LCD Display Sets LCD display waveform values. Use the

right key to enter units, and the left key to enter

tens. Press the top of the key to increase the

value. Press the bottom of the key to decrease

the value.

3. Enter Pressing this stores newly specified waveform

value set by the keys.

4. High Level ECG

Connector

Standard phone jack connecting the high level

ECG output signal.

5. BASE (Baseline

Impedance) Slide

Switch

Sets the impedance between each lead. The

respiration parameter (breathing rate/min) is

selected and stored in the display.

6. LEAD Slide

Switch

Determines which lead is in use. The position

of the switch must correspond to the type of

patient monitor in use.

7. Blood Pressure

Slide Switch

(µV/V/mmHg)

Sets the sensitivity to match the input sensitivity

of the patient monitor (either 5 or 40

FV/V/mmHg). The waveform is selected and

stored in the display.

8. Temperature

Slide Switch

Sets the temperature to be used.

9. Lead Test

Terminals

For testing ECG leads. Connect each end of

the lead to one of the two Lead Test Terminals.

The LCD display will flash if the lead is OK.

MaxiSim 2000 Patient Simulator

Rear Panel

10. Low level ECG

Connectors

10 AHA color-coded 4mm safety

terminals. Snap-to-banana

adapters for the terminals are

supplied with the MaxiSim 2000.

11. Battery

Eliminator

Micro jack for connecting the 9V

plug-in power supply transformer

for use in operating the unit from

any standard electrical outlet.

USE

1. Power

The power switch is the slide-switch situated at the bottom right-

hand corner of the panel. The instrument should be switched off

when not in use, to save the battery. A flashing display indicates

low battery power.

2. Battery Replacement

The battery is situated in the base of the instrument. Use a 9 volt

alkaline battery.

3. Top Panel Controls and Connectors Display and Keyboard

The MaxiSim 2000 has a two-digit display. To the left of the LCD

display is a listing of available waveforms and two-digit codes.

Access a waveform by displaying its corresponding two-digit code.

Use the two keys below the LCD display to enter units and tens

(the right key is for units; the left is for tens). Pressing the top of

the keys increases the values, while pressing the bottom of the

keys decreases the values. The selected waveform is stored by

pressing Enter. Repeat the above procedure if you desire to store

several waveforms. By using the left-hand key (tens), you can

switch between waveforms stored in the instrument.

When the apparatus is switched on, the display will show the

program version for a short period before switching into standard

mode.

Manual ECG, High Level Output

The high level ECG output signal is a Lead II waveform with

0.5V/mV of low level Lead II. The high level ECG connection

(standard phone jack) is situated in the upper left-hand corner of

the instrument.

NOTE

Use only BC Biomedical

AC Adapter plug-in power

supply transformer

supplied with the unit.

NOTE

Do not use mercury,

air or carbon-zinc

batteries.

NOTE

When the instrument

is switched off, all

stored information will

be canceled.

Respiration

The respiration signal is transferred via ECG connections. The

position of the LEAD switch determines which lead is in use. The

position of the switch must correspond to the type of patient

monitor being used. The BASE (baseline impedance) switch sets

the impedance between each lead. The respiration parameter

(breathing rate/min.) is selected and stored in the display.

Blood Pressure

The sensitivity switch (pVN/mmHg) must be set to match the input

sensitivity of the patient monitor (either 5 or 40 pVN/ mmHg). The

waveform is selected and stored in the display. Prewired cables

and diagrams for connecting various types of monitors are

available from BC Biomedical. Unterminated cables are also

available.

CABLE CONNECTION MATRIX

BLOOD PRESSURE CABLE

DIN Plug Pin No. Color Function

4 Black Output (+)

1 Red Output (-)

3 White Exciter (+)

5 Green Exciter (-)

2 Blue ECG ref

Temperature

(See below). The type of cable used determines the type of probe

simulated, either 400 or 700 series YSI probes. Temperature is

selected by a slide switch. Prewired 400/700 YSI-series

temperature cables to connect to the temperature connector are

available from BC. Unterminated cables are also available.

CABLE CONNECTION MATRIX

UNIVERSAL TEMPERATURE CABLES

DIN Plug Pin No.

Color

OUTPUT 1

400 Series

OUTPUT 2

700 Series

1 Green Tip No conn.

2 Red No conn. Tip

3 White No conn. Ring

4 Black Barrel Barrel

Lead Testing

ECG leads should be tested regularly. Connect each end of a lead to one

of the two Lead Test terminals. The display will flash if the lead is OK.

4. Rear Panel Connectors

Low-Level ECG Leads

There are ten AHA color-coded 4mm safety terminals located on the rear

panel. Snap-to-banana adapters for the terminals are supplied with the

MaxiSim 2000

Battery Eliminator

BC Biomedical’s AC Adapter plug-in power supply transformer allows you

to use the MaxiSim 2000 anywhere a standard electrical outlet is

available. To attach the AC Adapter insert the adapter’s small connector

into the micro jack labeled “Batt. Elim. 9V DC” on the right rear of the unit.

Plug the large connector into the nearest standard electrical outlet.

NOTE

Remove the batteries

and disconnect the AC

dapter if you do not

intend to use the

MaxSim 2000 for an

extended period of time.

Tabla de contenidos

Otros manuales de Equipo médico de BC Biomedical

BC Biomedical

BC Biomedical FINGERSIM PULSE OXIMETER TEST SYSTEM Instruction... Guía de solución de problemas

BC Biomedical

BC Biomedical PS-2110 Manual de usuario

BC Biomedical

BC Biomedical Auxiliary ESU Load Resistor Manual de usuario

BC Biomedical

BC Biomedical PS-2200 series Manual de usuario

BC Biomedical

BC Biomedical PLA Manual de usuario

BC Biomedical

BC Biomedical NIBP-1010 Manual de usuario

BC Biomedical

BC Biomedical ENDOCHECK Test system Manual de usuario

BC Biomedical

BC Biomedical ESU-2000 Series Guide Manual de usuario

BC Biomedical

BC Biomedical PS-2105 Manual de usuario

Manuales populares de Equipo médico de otras marcas

TekTone

TekTone Tek-CARE160 Manual de usuario

NeuroMetrix

NeuroMetrix Quell 2.0 Manual de usuario

AMT

AMT XLR8 Manual de usuario

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 Manual de usuario

EDAN

EDAN SONOTRAX Pro Manual de usuario

Restorative Therapies

Restorative Therapies RT300 Manual de usuario

Gendex

Gendex Expert DC Manual de usuario

Dexcowin

Dexcowin ADX4000W Manual de usuario

Libelium

Libelium MySignals Manual de usuario

Acelity

Acelity V.A.C.ULTA 4 Manual de usuario

Caputron

Caputron ActivaDose II tDCS Manual de usuario

FujiFilm

FujiFilm Sonart Manual del propietario

Plinth 2000

Plinth 2000 93CDT Manual de usuario

GE SENOGRAPHE 800T Manual de usuario

GE Definium 5000 Manual de usuario

Kanmed

Kanmed GE-1380 Manual de usuario

Huntleigh

Huntleigh FD1 Manual de usuario

Stryker

Stryker SPR Plus Manual de usuario