BBB DIGIBOARD Manual de usuario

Complete manual

BCP-51W

BCP-51WH

BCP-52WA

BCP-52WAH

CyCling Computer

DigiboarD

English

SCreen elementS

SCREEN ELEMENTS

» BCP-52WA / BCP-52WAH

» BCP-51W / BCP-51WH

operationS button

OPERATIONS BUTTON

ContentS

SECTION 1 : inStallation

A Hardware: Mounting bracket, wheel magnet and speed sensor

B. Heart rate: Heart rate sensor set

C. Cadence: Cadence magnet and cadence sensor

SECTION 2 : FIRST TIME SET-UP

A. Battery installation

B. Settings

» Setting clock

» Setting heart rate values

» Setting gender

» Setting weight

» Setting wheel size

» Setting Km/h or M/h

» Setting odometer 1

» Setting total time 1

» Pairing

C. Setting home altitude

SECTION 3 : BEFORE EACH RIDE

» Trip data reset

» Home altitude calibration

SECTION 4 : ADVANCED SETTINGS

A. Second bike set-up

B. Advanced time settings

C. Advanced trip distance settings

D. Advanced heart rate settings

E. Advanced cadence settings

F. Advanced altitude settings

G. Temperature and Backlight

SECTION 5 : ADDITIONAL INFORMATION

A. Menu structure

B. Display elements

C. Functions overview

D. Troubleshooting

E. Technical specifications

SeCtion 1

inStallation

SECTION 1A : inStallation - HarDWare

1. Install the wheel magnet on a spoke, using a Phillips srewdriver.

2. Position the speed sensor on the fork leg to achieve the correct alignment with the wheel mag-

net. If needed, move the wheel magnet. When you have achieved the correct alignment, pass

two zip-ties through the speed sensor and around the fork leg.

3. Re-check the alignment of the speed sensor, and tighten both zip-ties. The distance between

the wheel magnet and the sensor point should be maximum 5mm.

4. Cut off the excess length of the zip-ties.

INSTALLING THE WHEEL MAGNET AND SPEED SENSOR

124

5. The bracket can be installed on the stem as well as the handlebar. The bracket is pre-assembled

in the handlebar position.

6. If you would like to have your computer on the stem, loosen the four screws on the bracket,

rotate the bracket 90 degrees and tighten the four screws.

7. Pass two zip-ties through the bracket and around the stem/handlebar. Cut off the excess length

of the zip-ties.

8. Place the BBB computer in the bracket and rotate clockwise till you hear a “click” sound.

INSTALLING THE COMPUTER BRACKET

SECTION 1B : inStallation - Heart rate

The heart rate sensors are integrated in the soft elastic belt. For

a correct heart rate measurement, the belt must be positioned

slightly below your chest, directly on your skin.

1. Make the two contact areas moist before you start your exer-

cise.

2. The chest belt needs to be snug to stay in place. Slide the buck-

les to adjust the length of the belt for a snug but comfortable

fit.

3. Press the ANT+ transmitter to the elastic belt on the two push-

button connectors.

Maintenance

- Remove the transmitter from the elastic belt after every use

and dry the push-buttons connectors on the transmitter. Rinse

the soft elastic belt under running water after every use.

- Wash the elastic belt regularly in a washing machine at 30ºC.

Use a washing pouch. Do not spin-dry, iron, dry clean or bleach

the elastic belt. Do not use detergent with bleach or fabric soft-

ener.

- Never put the transmitter in the washing machine!

INSTALLING THE HEART RATE SENSOR

The sensor batteries are pre-installed. When needed, check below illustrations for correct

replacement.

1. Open the battery cover by turning the cover counter clockwise.

2. Insert the battery (CR 2032) with the negative side (-) facing up for 3 seconds. This will

reset the sensor.

3. Insert the battery (CR 2032) with the positive side (+) facing up. Close the battery cover by

turning it clockwise.

Batteries should be disposed of in compliance with local regulations.

» BATTERY REPLACEMENT FOR THE HEART RATE SENSOR

SECTION 1C : inStallation - CaDenCe

1. Install the cadence magnet on the non drive train side of the crank.

2. Install the cadence sensor on the chainstay.

3. Position the cadence sensor on the chainstay to achieve the correct alignment with the cadence

magnet. If needed, move the cadence magnet. The distance between the magnet and the sensor

point should be maximum 3mm. When you have achieved the correct alignment, pass two zip-

ties through the sensor and around the chainstay.

4. Cut off the excess length of the zip-ties.

INSTALLING THE CADENCE MAGNET AND CADENCE SENSOR

124

The sensor batteries are pre-installed. When needed, check below illustrations for correct

replacement.

1. Open the battery cover by turning the cover counter clockwise.

2. Insert the battery (CR 2032) with the negative side (-) facing up for 3 seconds. The will

reset the sensor.

3. Insert the battery (CR 2032) with the positive side (+) facing up. Close the battery cover by

turning it clockwise.

Batteries should be disposed of in compliance with local regulations.

» BATTERY REPLACEMENT FOR THE CADENCE SENSOR

SeCtion 2

FirSt time Set-up

SECTION 2A : FirSt time Set-up : battery

1. Open the battery cover by turning the cover counter clockwise.

2. Insert the battery (CR 2032) with the positive side (+) facing up. Close the battery cover by

turning it clockwise

After the battery installation the first time setup menu will start automatically.

The first time setup procedure can be restarted by pressing the “AC” button on the back side the of

computer.

INSTALLING BATTERY INTO THE COMPUTER

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios para bicicletas de BBB

BBB

BBB BCP-01 Manual de usuario

BBB

BBB BCP-04C Manual de usuario

BBB

BBB BCP-22 Manual de usuario

BBB

BBB BCP-51W Manual de usuario

BBB

BBB BCP-05 Manual de usuario

BBB

BBB BCP-01 Manual de usuario

BBB

BBB SWAT Manual de usuario

BBB

BBB BCP-01 Manual de usuario

BBB

BBB BCP-32 Manual de usuario

BBB

BBB nanostrike BLS-130 Manual de usuario

BBB

BBB BCP-51W Manual de usuario

Manuales populares de Accesorios para bicicletas de otras marcas

Sigma

Sigma BC 16.16 Manual de usuario

Playcore

Playcore Dero Setbacks Manual de usuario

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manual de usuario

Cateye

Cateye RAPID X2 Manual de usuario

buratti meccanica

buratti meccanica Clorofilla Trail Manual de usuario

Shimano

Shimano SG-8R20 Instrucciones de funcionamiento

BOB

BOB YAK Manual de usuario

APLIC

APLIC 303303/20190717TW012 Manual de usuario

SRAM

SRAM AXS BlipBox Manual de usuario

Garmin

Garmin EDGE 500 Manual de usuario

Shimano

Shimano FD-RX810 Manual de usuario

Cateye

Cateye V2C - Manual de instrucciones

KMART

KMART 43115907 Manual de usuario

SIGMA SPORT

SIGMA SPORT Buster 2000 Manual de usuario

NVO Components

NVO Components STEM Manual de usuario

DAXYS

DAXYS BP188 Manual de usuario

XLC

XLC BV-W17 Manual de usuario

Deda Elementi

Deda Elementi SUPERBOX Manual de usuario