Bay Alarm Vista-20Bay Instrucciones de montaje

N7526-4V1 5/00 File No: S1632

9,67$%$<

6HFXULW\6\VWHP

,QVWDOODWLRQDQG6HWXS*XLGH

I I I I I I

OFF AWAY STAY

MAX TEST BYPASS

INSTANT CODE CHIME

READY

PANIC

SINCE 1946

Liberty System

ARMED

BYP SS CTIVEHE T COOL

SINCE 1946

iii

RECOMMENDATIONS FOR PROPER PROTECTION

The Following Recommendations For The Location Of Fire And Burglary Detection

Devices Help Provide Proper Coverage For The Protected Premises.

R comm ndations for Smok and H at D t ctors

With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations

contained in the National Fire Protection Association's (NFPA) Standard #72 noted below.

Early-warning fire detection is best achieved by the installation of fire detection equipment in all rooms

and areas of the household as follows: For minimum protection, a smoke detector should be installed

outside of each separate sleeping area, and on each additional floor of a multi-floor family living unit,

including basements. The installation of smoke detectors in kitchens, attics (finished or unfinished), or in

garages is not normally recommended.

For additional protection the NFPA recommends that you install heat or smoke detectors in the living

room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms,

basements and attached garages.

In addition, we recommend the following:

• Install a smoke detector inside every bedroom where a smoker sleeps.

• Install a smoke detector inside every bedroom where someone sleeps with the door partly or

completely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside

may not wake up the sleeper if the door is closed.

• Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air

conditioners or humidifiers) are used.

• Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long.

• Install smoke detectors in any room where an alarm control is located, or in any room where alarm

control connections to an AC source or phone lines are made. If detectors are not so located, a fire

within the room could prevent the control from reporting a fire or an intrusion.

THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR

TEMPORAL PULSE SOUNDING OF FIRE NOTIFICATION APPLIANCES.

DINING

KITCHEN

BEDROOM

LIVING ROOM

✪

✪✪

✪

▲

BEDROOM

BDRM

DINING

LIVING ROOM

TV ROOM KITCHEN

■■

■

✪

✪✪

✪

▲

✪

BEDROOM BEDROOM

■

LVNG RM

B SEMENT

KTCHN

▲

CLOSED

DOOR

G R GE

▲

Smoke Detectors for Minimum Protection

Smoke Detectors for dditional Protection

Heat- ctivated Detectors

R comm ndations for Prop r Intrusion Prot ction

For proper intrusion coverage, sensors should be located at every possible point of entry to a home or

commercial premises. This would include any skylights that may be present, and the upper windows in a

multi-level building.

In addition, we recommend that radio backup be used in a security system so that alarm signals can still be

sent to the alarm monitoring station in the event that the telephone lines are out of order (alarm signals are

normally sent over the phone lines, if connected to an alarm monitoring station).

Tabl of Cont nts

••••••••••••••••••••••••••••••••••••••••••••••••••

Conventions Used in This Manual ............................................................................................................... viii

Section 1 - Introduction .............................................................................................................................1–1

Description .......................................................................................................................................................1–1

Features............................................................................................................................................................1–1

Section 2 - Installing the Control.............................................................................................................2–1

General Information........................................................................................................................................2–1

Mounting the Cabinet .....................................................................................................................................2–1

Installing the Lock (if used) ............................................................................................................................2–1

Mounting the Control's Circuit Board Alone in the Cabinet ........................................................................2–2

Mounting Control and RF Receiver Circuit Boards Together in the Cabinet .............................................2–3

Standard Phone Line Connections .................................................................................................................2–4

Wiring the AC Transformer ............................................................................................................................2–5

Installing the Backup Battery ........................................................................................................................2–6

Earth Ground Connections .............................................................................................................................2–6

Section 3 - Installing Remote Keypads...................................................................................................3–1

General Information........................................................................................................................................3–1

Keypads That May Be Used............................................................................................................................3–1

Wiring to the Keypads.....................................................................................................................................3–1

Mounting the Keypads ....................................................................................................................................3–2

Using a Supplementary Power Supply to Power Additional Keypads.........................................................3–2

Preliminary Checkout Procedure ...................................................................................................................3–3

Section 4 - Basic Hardwired Zones 1–8...................................................................................................4–1

General Information........................................................................................................................................4–1

Installing the Hardwired Zones......................................................................................................................4–1

Programming Hardwired Zones .....................................................................................................................4–5

Checkout Procedure for Hardwired Zones .....................................................................................................4–5

Section 5 - Wired Zone Expansion ...........................................................................................................5–1

Introduction .....................................................................................................................................................5–1

Installing Zone Expansion Units....................................................................................................................5–1

Connections and Setup....................................................................................................................................5–1

Programming Wired Expansion Zones...........................................................................................................5–3

Checkout Procedure for Wired Expansion Zones ..........................................................................................5–3

Section 6 - Wireless Expansion (5800 System)......................................................................................6–1

About Wireless Expansion ..............................................................................................................................6–1

Installing the 5881/5882 Receiver ..................................................................................................................6–2

Installing the 5800TM Module .......................................................................................................................6–3

Jam Detection and Reporting .........................................................................................................................6–3

About 5800 Series Transmitters.....................................................................................................................6–3

Installing 5800 Series Transmitters...............................................................................................................6–7

Section 7 - Relay Outputs & Powerline Carrier Devices ...................................................................7–1

Relay/Powerline Carrier Device Basics..........................................................................................................7–1

4204 and 4229 Relay Modules ........................................................................................................................7–1

Powerline Carrier Devices ..............................................................................................................................7–3

Programming Relay Outputs..........................................................................................................................7–4

Section 8 - 4285 & 4286 VIP Module.........................................................................................................8–1

Introduction .....................................................................................................................................................8–1

Installing the Phone Module...........................................................................................................................8–1

Programming the 4285/4286 VIP Module......................................................................................................8–4

Checking 4285/4286 VIP Module Operation..................................................................................................8–4

Table of Contents (cont’d)

Section 9 - External Sounders ..................................................................................................................9–1

Compatible Sounders.......................................................................................................................................9–1

Sounder Connections.......................................................................................................................................9–2

Sounder Supervision .......................................................................................................................................9–2

Testing the Sounder ........................................................................................................................................9–2

Section 10 - Long Range Radio.................................................................................................................10–1

About Long Range Radio...............................................................................................................................10–1

Connection......................................................................................................................................................10–1

Dynamic Signaling Feature ..........................................................................................................................10–2

Section 11 - Remote Keyswitch.................................................................................................................11–1

Introduction ...................................................................................................................................................11–1

Installing the Keyswitch ...............................................................................................................................11–1

Programming for the Remote Keyswitch .....................................................................................................11–3

Keyswitch Operation .....................................................................................................................................11–4

Section 12 - Audio Alarm Verification (AAV) Unit...............................................................................12–1

General Information......................................................................................................................................12–1

Wiring Connections .......................................................................................................................................12–1

Section 13 - Final Power-Up......................................................................................................................13–1

Earth Ground Connections ...........................................................................................................................13–1

AC Power-Up .................................................................................................................................................13–1

Connecting the Backup Battery....................................................................................................................13–1

Battery Tests..................................................................................................................................................13–2

Section 14 - Mechanics of Programming................................................................................................14–1

About Programming ......................................................................................................................................14–1

Entering Program Mode................................................................................................................................14–2

Programming a Data Field............................................................................................................................14–2

Reviewing a Data Field/Erasing an Entry ...................................................................................................14–2

Interactive Mode Programming (✱56, ✱58, ✱80, ✱81, and ✱82)................................................................14–2

Loading Factory Defaults..............................................................................................................................14–3

Programming System Setup Fields..............................................................................................................14–3

Exiting the Programming Mode ...................................................................................................................14–3

Section 15 - Zone Response Type Definitions.......................................................................................15–1

Zone Type Definitions....................................................................................................................................15–1

Section 16 - Data Field Descriptions.......................................................................................................16–1

Introduction ...................................................................................................................................................16–1

Descriptions of System Data Fields..............................................................................................................16–1

Section 17 - Zone Programming ...............................................................................................................17–1

About Zone Programming .............................................................................................................................17–1

✱56 Zone Programming Procedures.............................................................................................................17–1

✱58 Expert Programming Mode Procedures ...............................................................................................17–4

To Remove a Zone..........................................................................................................................................17–6

To Delete a Transmitter Serial Number ......................................................................................................17–7

To Enter and Duplicate Wireless Keys ........................................................................................................17–7

Section 18 - Output Device Programming .............................................................................................18–1

Programming Options Defined .....................................................................................................................18–1

Programming Output Relays and Powerline Carrier Devices....................................................................18–3

Section 19 - Zone Lists ................................................................................................................................19–1

About Zone List Menu Mode.........................................................................................................................19–1

Zone List Displays .........................................................................................................................................19–1

Section 20 - Alpha Descriptor Programming ........................................................................................20–1

About Alpha Descriptor Programming.........................................................................................................20–1

Zone Descriptors ............................................................................................................................................20–1

Programming Zone Descriptors (program menu mode ✴82)......................................................................20–1

Adding Custom Words...................................................................................................................................20–3

Table of Contents (cont’d)

Section 21 - Remote Programming and Control (Downloading)......................................................21–1

About Remote Programming.........................................................................................................................21–1

Equipment Required .....................................................................................................................................21–1

Initial Download ............................................................................................................................................21–2

Remote Programming Commands................................................................................................................21–2

Remote Programming Advisory Notes .........................................................................................................21–2

Section 22 - System Communication.......................................................................................................22–1

Panel Communication with Central Station................................................................................................22–1

Report Code Formats.....................................................................................................................................22–1

Section 23 - System Operation..................................................................................................................23–1

Security Codes ...............................................................................................................................................23–1

Keypad Functions..........................................................................................................................................23–2

Relay/Powerline Carrier Devices..................................................................................................................23–3

4285/4286 VIP Module (if used)....................................................................................................................23–3

Exit Error Alarm Displays (if programmed)................................................................................................23–3

Trouble Conditions ........................................................................................................................................23–4

Section 24 - Testing the System................................................................................................................24–1

Test Procedure ...............................................................................................................................................24–1

Section 25 - Troubleshooting Guide........................................................................................................25–1

Section 26 - Specifications & Accessories..............................................................................................26–1

Specifications .................................................................................................................................................26–1

Accessories (Compatible Devices).................................................................................................................26–3

Appendix A - 5800 RF System Wireless Transmitters ............................................................................A–1

Transmitter Input Loop Identification.......................................................................................................... A–1

Appendix B - Regulatory Agency Statements...........................................................................................B–1

Appendix C - Warnings and Limited Warranty........................................................................................ C–1

Index...........................................................................................................................................................Index - 1

Programming Form ...................................................................................................................................Insert

vii

List of Figur s

••••••••••••••••••••••••••••••••••••••••••••••••••

Figure 1. Installing the Cabinet Lock.................................................................................................................2–2

Figure 2. Mounting the PC Board.......................................................................................................................2–2

Figure 3. Mounting the PC Board and RF Receiver Together in the Cabinet.................................................2–3

Figure 4. Telephone Line Connections ...............................................................................................................2–4

Figure 5. Connections of 4300 Transformer to the Control Board ...................................................................2–5

Figure 6. Keypad Connections to the Control Board.........................................................................................3–2

Figure 7. Using a Supplementary Power Supply for Keypads .........................................................................3–3

Figure 8. 2-Wire Smoke Detector Connected to Zone 1.....................................................................................4–2

Figure 9. 4-Wire Smoke Detector Connections (Zones 2–7)..............................................................................4–3

Figure 10. Glassbreak Detector Connections to Zone 8.....................................................................................4–4

Figure 11a. Wiring Connections, 4219 Expansion Module ...............................................................................5–2

Figure 11b. Wiring Connections, 4229 Expansion Module ...............................................................................5–2

Figure 12. 5881/5882 RF Receiver (cover removed)...........................................................................................6–2

Figure 13. 4204 Connections to Control .............................................................................................................7–2

Figure 14. 4229 Connections to Control .............................................................................................................7–3

Figure 15. 4300 Transformer Wiring Connections ............................................................................................7–4

Figure 16. 4285/4286 VIP Module Wiring Connections ....................................................................................8–3

Figure 17. Typical Sounder Wiring......................................................................................................................9–2

Figure 18. Bell Supervision Wiring .....................................................................................................................9–2

Figure 19. Long Range Radio Connections ......................................................................................................10–1

Figure 20a. Keyswitch Wiring (4300 Interface Transformer not used)..........................................................11–2

Figure 20b. Keyswitch Wiring (4300 Interface Transformer also used) ........................................................11–2

Figure 21. Connection of AAV Unit When not Using a 4285/4286 VIP Module ............................................12–2

Figure 22. Connection of AAV Unit When also Using a 4285 or 4286 VIP Module ......................................12–2

Figure 23. VISTA-20BAY Summary of Connections ................................................................ Inside Back Cover

viii

Conv ntions Us d in This Manual

••••••••••••••••••••••••••••••••••••••••••••••••••

Before you begin using this manual, it is important that you understand the meaning of the following

symbols:

UL UL note includes specific information that must be followed if you are installing this system for a

UL Listed application.

checked note includes information you should be aware of before continuing with the

installation, and which, if not observed, could result in operational difficulties.

This symbol warns of conditions that could seriously affect the operation of the system, or cause

damage to the system. Please read each warning carefully. This symbol also denotes warnings

about physical harm to the user.

Enter Zone Num.

(00 = Quit)

You may program many system options by responding to alpha keypad display

prompts. These prompts are shown in a double-line box.

✴00 When programming the system, data fields are indicated by a “star” (✴) followed by

the data field number.

PRODUCT MODEL NUMBERS: Unless noted otherwise, references to specific model numbers represent

ADEMCO products.

1–1

SECTION 1

Introduction

••••••••••••••••••••••••••••••••••••••••••••••••••

In This S ction

♦Description ♦Features

••••••••••••••••••••••••••••••••••••••••••••••••••

D scription

The VISTA-20BAY is a security system control that supports up to 38 zones, including eight

basic hardwired zones (1 through 8) and a maximum of 30 expansion zones. These expansion

zones may include up to eight hardwired zones, or up to 30 wireless zones if hardwired zones

are not used. Three separate keypad-activated zones are also provided.

F atur s

Basic Hardwir d Zon s

Provides 8 basic hardwired zones having the following characteristics:

• EOLR supervision supporting N.O. or N.C. sensors

• Programmable response time (10, 350, or 700 milliseconds)

• Up to sixteen 2-wire smoke detectors on zone 1

• 4-wire smoke or heat detectors on zones 2 through 7 (as many as can be powered from

Auxiliary Power on the control).

NOTE: 4-wire smoke/heat detectors cannot be used in UL installations

• Up to fifty 2-wire latching-type glassbreak detectors on zone 8 with auto reset

Optional Expansion Zon s (up to 30 total, wir d and wir l ss)

Wir d Expansion:

Supports up to 8 additional wired zones using a 4219 Expansion Module or 4229

Expansion/Relay Module. These zones have the following characteristics:

• EOLR supervision supporting N.O. or N.C. sensors

• 300-500mSec normal response with an option for fast (10-15mSec) response on loop A

(first expansion zone)

Wir l ss Expansion:

Supports up to 30 wireless zones (less if using wired expansion zones).

• Requires the use of a 5881 (5882 in Canada) type RF receiver, as indicated below:

Receiver Model No. of Zones

5881L/5882L Up to 8

5881M/5882M Up to 16

5881H/5882H Up to 30

• Requires the use of 5800 Series Wireless Transmitters

VISTA-20BAY Installation & Setup Guide

1–2

R mot K ypads

Up to 4 of either of the following keypads may be used in the installation:

• Fixed-Word Keypad: 6128

• Alpha Keypad: SK6139A-BAY (2-line alphanumeric displays).

To program from a keypad, you must connect a SK6139 -B Y 2-line alpha keypad, but it need not

stay in the system.

S curity Cod s

The system supports the following security codes:

• One Installer code for entire system (user 1)

• One Master code for entire system (user 2)

• 12 Secondary User codes (users 3-14)

• One Babysitter code (user 15)

• One Duress code (user 16).

Babysitter Code: special code that can be used to disarm the system only if that particular code

was used to arm it.

Duress Code: n emergency code which, when entered by

any

user to disarm or arm the system,

will send a silent duress message to the Central Station.

K ypad Panic K ys

• Up to 3 programmable panic key functions (designated as zones 95, 96, and 99)

• Activated by wired and wireless keypads

• Distinguished by subscriber ID number

Zon Monitor F atur

The control senses a high resistance in the loops on hardwired zones 2-8 if it is present, and

displays a trouble message (rather than an alarm) for the affected zone when the system is in

the disarmed mode. This feature also prevents the system from being armed while this high-

resistance condition exists.

Exit Error Fals Alarm Pr v ntion F atur

This feature enables the system to determine the difference between an actual alarm and an

alarm caused by leaving an Entry/Exit or Interior zone open after the Exit Delay expires. If

it is not disarmed in time, an alarm sounds and an Exit Error report is sent to the Central

Station.

An Exit Alarm condition also occurs if an Entry/Exit or Interior zone re-opens within 2

minutes after the end of an Exit Delay.

Optional Output R lays and Pow rlin Carri r D vic s (X-10 typ )

• Up to 4 relays using one 4204 Relay Module

• Up to 2 relays using one 4229 Zone/Relay Module

• Up to 8 Powerline Carrier devices are supported (you must subtract the number of relay

outputs actually used by the 4204 or 4229 modules, if used)

• Actions are programmable to respond to zone activity or manual keypad entries.

Otros manuales para Vista-20Bay

Tabla de contenidos

Otros manuales de Sistema de seguridad de Bay Alarm

Bay Alarm

Bay Alarm In-Home Medical Alert System Manual de usuario

Bay Alarm

Bay Alarm Vista-20Bay Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario