BAUKER BTC180B Guía del usuario
ORIGINAL INSTRUCTION MANUAL
BTC180B
600W TILE CUTTER
EN-2
Important - Please read these instructions fully before starting assembly
General Power Tool Safety Warnings
SAFETY INFORMATION
WARNING! When using electric tools basic safety
precautions should always be followed to reduce the risk of
re, electric shock and personal injury including the following.
Read all these instructions before attempting to operate this product
and save these instructions".
Maintenance and Servicing
Remove the plug before carrying out any adjustment, servicing or
maintenance.
Safe operation
1. Keep work area clear
- Cluttered areas and benches invite injuries.
2. Consider work area environment
- Do not expose tools to rain.
- Do not use tools in damp or wet locations.
- Keep work area well lit.
- Do not use tools in the presence of ammable liquids or gases.
3. Guard against electric shock
- Avoid body contact with earthed or grounded surfaces {e.g.
pipes, radiators, ranges, refrigerators).
4. Keep other persons away
- Do not let persons, especially children, not involved in the work
touch the tool or the extension cord and keep them away from
the work area.
5. Store idle tools
- When not in use, tools should be stored in a dry locked-up
place, out of reach of children.
6. Do not force the tool
- It will do the job better and safer at the rate for which it was
intended.
7. Use the right tool
- Do not force small tools to do the job of a heavy duty tool.
- Do not use tools for purposes not intended; for example do not
use circular saws to cut tree limbs or logs.
8. Dress properly
- Do not wear loose clothing or jewellery, they can be caught in
moving parts.
EN-3
Important - Please read these instructions fully before starting assembly
General Power Tool Safety Warnings
- Non-skid footwear is recommended when working outdoors.
- Wear protective hair covering to contain long hair.
9. Use protective equipment
- Use safety glasses.
- Use face or dust mask if working operations create dust.
10. Connect dust extraction equipment
- If the tool is provided for the connection of dust extraction and
collecting equipment, ensure these are connected and properly
used.
11. Do not abuse the cord
- Never yank the cord to disconnect it from the socket Keep the
cord away from heat, oil and sharp edges.
12. Secure work
- Where possible use damps or a vice to hold the work. It is safer
than using your hand.
13. Do not overreach
- Keep proper footing and balance at all times.
14. Maintain tools with care
- Keep cutting tools sharp and clean for better and safer
performance.
- Follow instruction for lubricating and changing accessories.
- Inspect tool cords periodically and if damaged have them
repaired by an authorized service facility.
- Inspect extension cords periodically and replace if damaged.
- Keep handles dry, clean and free from oil and grease.
15. Disconnect tools
- When not in use, before servicing and when changing
accessories such as blades, bits and cutters, disconnect tools
from the power supply.
16. Remove adjusting keys and wrenches
- Form the habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning it on.
17. Avoid unintentional starting
- Ensure switch is in "off” position when plugging in
18. Use outdoor extension leads
- When the tool is used outdoors, use only extension cords
intended for outdoor use and so marked.
19. Stay alert
- Watch what you are doing, use common sense and do not
EN-4
operate the tool when you are tired.
20. Check damaged parts
- Before further use of tool, it should be carefully checked to
determine that it will operate properly and perform its intended
function.
- Check for alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions that may
affect its operation.
- A guard or other part that is damaged should be properly
repaired or replaced by an authorized service centre unless
otherwise indicated in this instruction manual.
- Have defective switches replaced by an authorized service
centre.
- Do not use the tool if the switch does not turn it on and off.
21. Warning
- The use of any accessory or attachment other than one
recommended in this instruction manual may present a risk of
personal injury.
22. Have your tool repaired by a qualied person
- This electric tool complies with the relevant safety rules.
Repairs should only be carried out by qualied persons using
original spare parts, otherwise this may result in considerable
danger to the user.
23. If the replacement of the supply cord is necessary, this has to
be done by the manufacturer or his agent in order to avoid a
safety hazard.
24. For tools intended to be connected to a water supply:
- Never use the tool without the PRCD delivered with the tool,
- Replacement of the plug or the supply cord shall always
be carried out by the manufacturer of the tool or his service
organisation,
- Keep water clear off the electrical parts of the tool and away
from persons in the working area.
EN-5
SYMBOLS
To reduce the risk of injury, user must read instruction manual
Wear eye protection
Wear ear protection
Wear dust mask
Warning
Double insulation
Always wear gloves
Remove plug from mains before maintenance or if cord is damaged.
Waste electrical products must not be disposed of with household waste. Please recycle
where facilities exist. Check with your local authorities or retailer for recycling advice.
EN-6
4 5 6 7
8
9
10
1
12
11
2
3
EN-7
14
15
16
17
18
13
2
Inner domed washer Outer domed washer
A B
C D
E F
G H
I J
K
EN-8
14
15
16
17
18
13
2
Inner domed washer Outer domed washer
A B
C D
E F
G H
I J
K
EN-9
COMPONENT LIST
1. ON/OFF SWITCH
2. PARALLEL GUIDE SECURING KNOB (ONE EACH SIDE)
3. FIXING PLATE(UNDER THE TABLE EDGE)
4. PARALLEL GUIDE
5. MITER GAUGE
6. BLADE GUARD
7. BLADE GUARD BRACKET
8. DIAMOND CUTTING BLADE
9. BLADE GUARD COVER AND SPACING PLATE
10. WATER TRAY
11. TABLE ANGLE SECURING KNOB (ONE EACH SIDE)
12. RCD SWITCH (ONLY FOR BTC180B.1)
Not all the accessories illustrated or described are included in standard delivery.
TECHNICAL DATA
Voltage
Power input
No load speed
Blade size
Cutting depth 90 degree
Table bevel range
Table size
Machine weight
Protection class
ACCESSORIES
Parallel guide 1
Water tank 1
45° miter gauge 1
Spanner 2
Blade 1
We recommend that you purchase your accessories from the same store that sold you the tool. Refer to
the accessory packaging for further details. Store personnel can assist you and offer advice.
230V~ 50Hz
600W S2:10 Min
2,950 /min
Φ180 x 2.2 xΦ25.4 mm
34 mm
0-45°
330 x 360 mm
8.4 kg
/ I
EN-10
NOISE AND VIBRATION DATA
A weighted sound pressure LpA =92dB(A)
KpA= 3.0dB(A)
A weighted sound power LwA =105dB(A)
KwA: 3.0dB(A)
Wear ear protection.
Tabla de contenidos
Manuales populares de Cortador de otras marcas
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Manual de usuario
Makita
Makita DCS552 Manual de usuario
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Manual de usuario
Makita
Makita 4112HS Manual de usuario
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Manual de usuario
Hitachi
Hitachi CM 4SB2 Guía de solución de problemas
