Basler CXP-12 Manual de usuario

QUICK INSTALL GUIDE

BASLER BOOST CXP-12

Basler AG

An der Strusbek 60–62

22926 Ahrensburg

Germany

All material in this publication is subject to change without notice and is

本出版物中的所有材料如有更改，恕不另行通知，且版权归

Basler AG

所有。

本文書のすべての内容は予告なしに変更される場合があります。また Basler AG

がその著作権を有します。

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

About this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Important Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Additional Accessories and Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

HARDWARE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Overview of the Components (Example Installation) . . . . . . . . . . . . . . . . 6

Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Step 1: Installing the Interface Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Step 2: Installing the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Step 3: Providing Camera Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

ACQUIRING YOUR FIRST IMAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Acquiring Images Using the pylon Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . 11

INTRODUCTION

About this Document

This document provides information about how to install a Basler

boost CXP-12 camera and a Basler CXP-12 Interface Card (referred to here

as "interface card").

It also provides step-by-step instructions that help you to connect the

camera and the interface card and acquire your first images.

Important Documentation

Before installing the hardware, Basler strongly advises reading the

precautions and safety instructions of the following documents:

Basler boost Getting Started Guide (AW001552)

Basler CXP-12 Interface Card 1C Getting Started Guide (AW001558)

Note: This document describes the installation of Basler products only,

i.e., Basler boost CXP-12 cameras, Basler CXP-12 interface cards, and

additional accessories needed for operation, such as cables or cooling

elements.

You can, however, use your own frame grabbers and accessories. In this

case, observe the documentation of the corresponding manufacturers

to ensure proper installation.

INTRODUCTION

For information about how to operate the Basler boost CXP-12 camera and

the Basler CXP-12 interface card, refer to the Basler Product Documentation

available at: docs.baslerweb.com

Additional Accessories and Software

Basler offers the following accessories that allow you to quickly get started

with your Basler boost CXP-12 camera:

CoaXPress 2.0 data cable, Micro-BNC x2 (HD-BNC), 3 m, 5 m, 10 m

Power-I/O cable M8 6p/open, 5 m, 10 m

Heat sink with mounting screws (M4x12)

Mount with mounting screws (M2.5x6), C-mount, F-mount, M42-mount

Power supply 18 W, M8 6p

These products can be purchased individually. Alternatively, you can

purchase the Basler CXP-12 Evaluation Kit boost, which includes a camera,

an interface card, and the accessories listed above apart from the power

supply.

For more information, visit www.baslerweb.com/boost.

The pylon Camera Software Suite (version 6.2 or higher) provides an SDK

for the camera and the interface card. Download the pylon Camera Software

Suite at: www.baslerweb.com/pylon

HARDWARE INSTALLATION

Overview of the Components (Example Installation)

Fig. 1: Example Installation of a Basler boost CXP-12 Camera with a C-mount Lens and a Basler

CXP-12 Interface Card 1C

VO.1 381JG848

RoHS 2011/65/EU

Status

LED

I/Oconnector

(M8 6-pin)

Micro-BNC

connector

Heat sink

C-mount

lens

2 x M4x12

4 x M2.5x6

Power-I/O

cable

CoaXPress

data cable

Micro-BNC

connector

Status

LED

D-Sub Micro-D

connector (15-pin)

PCIe power

connector (6-pin)

HARDWARE INSTALLATION

Prerequisites

The host computer must have at least one PCIe 3.0 x4 slot available on

the main board.

When using Power over CoaXPress (PoCXP), make sure that the power

supply of your computer provides a female 6-pin PCIe power connector.

If none is available, get an appropriate adapter.

If you are not using PoCXP, you need an external power supply.

Make sure that you have a suitable lens and the required accessories to

hand.

Step 1: Installing the Interface Card

1. Make sure that the host computer is shut down and unplugged from the

power outlet.

2. Remove the cover of the computer.

3. Plug the interface card into a free PCIe 3.0 x4 slot of the computer.

4. If you want to power the camera via the interface card (PoCXP), the

interface card needs to be connected to the power supply of the

computer.

Plug the female power supply connector of the computer to the power

connector of the interface card (PCIe 6-pin). If your computer doesn’t

provide a matching power supply connector, use an appropriate adapter.

HARDWARE INSTALLATION

5. Put the case of the computer back together.

Step 2: Installing the Camera

1. Make sure that the camera is disconnected from any power supply.

Contamination Hazard: Dust on the sensor may impair the camera’s

performance.

Make sure that the camera is pointing down during the next installation

steps.

2. Remove the seal from the camera front.

3. Attach a mount to the camera.

Note: If you want to use multiple interface cards in the same computer,

make sure that you have one PCIe 3.0 x4 slot per card on the main board

of that computer.

Use an adequate ventilation system within your computer and leave

sufficient free space between your interface card and other cards, if you

use any.

NOTICE

HARDWARE INSTALLATION

Damage Hazard: Inserting the lens too far into the camera may damage

the sensor.

When carrying out the next step, make sure not to insert the lens any

deeper than the specified maximum allowed lens intrusion.

For detailed information, refer to the Basler Product Documentation

available at: docs.baslerweb.com

4. Attach a suitable lens to the camera.

5. Provide sufficient heat dissipation, e.g., by attaching two heat sinks to

the camera.

Step 3: Providing Camera Power

1. If you are using PoCXP:

Plug one end of the CoaXPress cable into the Micro-BNC (HD-BNC)

connector of the camera and plug the other end of the CoaXPress cable

into the Micro-BNC connector of the interface card.

NOTICE

Note: The camera can be powered via PoCXP or via the I/O connector

using an external power supply (AUX power).

If you power your camera by both the CoaXPress interface and the

I/O connector, the power provided by the I/O connector is used only.

HARDWARE INSTALLATION

2. If you are using an external power supply:

a. Plug one end of the CoaXPress cable into the Micro-BNC (HD-BNC)

connector of the camera and plug the other end of the CoaXPress

cable into the Micro-BNC port of the interface card.

b. Connect the plug of the power I/O cable to the M8 6-pin connector

of the camera.

Observe the following pin assignment.

c. Connect the open end of the power I/O cable to a power supply.

d. Plug the power supply into a power outlet.

3. Reconnect the computer to the power outlet and boot the computer.

For information about the different LED states and corresponding colors,

refer to the Basler Product Documentation available at:

docs.baslerweb.com

Pin Line Function

I/O connector

of the camera

(M8 6-pin)

1 24 VDC camera power

2 1 Opto-coupled I/O input line

3 Ground for opto-coupled I/O lines

4 2 General purpose I/O (GPIO) line

5 3 General purpose I/O (GPIO) line

6 Ground for camera power and GPIO lines

Tabla de contenidos

Idiomas:

Otros manuales de Cámara digital de Basler

Basler

Basler aviator Camera Link Manual de usuario

Basler

Basler blaze-101 Manual de usuario

Basler

Basler DART BCON SERIES Manual de usuario

Basler

Basler ace Manual de usuario

Basler

Basler daA2500-14um Manual de usuario

Basler

Basler acA1300-75gc Hoja de instrucciones

Basler

Basler racer Manual de usuario

Basler

Basler Pioneer Manual de usuario

Basler

Basler A102f Manual de usuario

Basler

Basler A202k Manual de usuario

Basler

Basler ace Manual de usuario

Basler

Basler aviator Manual de usuario

Basler

Basler A202k Guía de configuración

Basler

Basler GigE VISION CAMERAS Manual de usuario

Basler

Basler A400K Manual de usuario

Basler

Basler ase Instrucciones de montaje

Basler

Basler A600f Guía de configuración

Basler

Basler A102K Manual de usuario

Basler

Basler GIGE VISION ace acA640-100gm/gc Manual de usuario

Basler

Basler A101f Manual de usuario

Basler

Basler A302f Manual de usuario

Basler

Basler A620f Manual de usuario

Basler

Basler acA2040-55 Manual de usuario

Basler

Basler dart Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Canon

Canon EOS ELAN7 Manual de usuario