Baroness LM56 Series Manual

Technical Information Leaflet

TIL: 013

LM56/66

Height of Cut Adjustment

HEIGHT OF CUT ADJUSTMENT

The setting bar for the Baroness LM56/66 range of mowers has two adjusting screws which

are used as follows:

This setting bar needs to be set as follows:

Groomer height setting screw. If no groomer

is fitted then this screw is not used.

Height of Cut Setting Screw

This end of this screw (as shown) needs to

be adjusted so that it measures the same

distance as the desired groomer setting.

This screw needs to be adjusted so that the

distance between the setting bar and the underside

of the head of the screw (as shown) is adjusted so

that it measures the same distance as the desired

height of cut.

Loosen the height of cut locking nut

using a 13mm spanner.

Once it is loose, lightly tighten it by

hand so that it is held in place but

able to be moved.

Repeat this on both sides of the

machine.

With the machine tipped back, fit the

setting bar as shown with the underside

of the adjusting screw head resting on

the cutting edge of the bottom blade.

Raise the front roller up by twisting

the height of cut adjuster nut anti-

clockwise. Make sure that you do

this on both sides of the machine by

equal amounts.

Note: This is only necessary if you

are lowering the current height of

cut. If you are raising the height of

cut you can skip this stage.

The end closest to the height adjusting

screw should be resting on the rear roller

as shown.

You now need to adjust the height of

the front roller until the correct

setting is achieved. To adjust the

front roller height, twist this

adjusting nut. Twisting it clockwise

will lower the roller and twisting it

anti-clockwise will raise the roller.

The front roller needs to be adjusted so that

with the underside of the adjusting screw

head resting on the cutting surface of the

bottom blade, the setting bar is touching

both the front and rear roller as shown.

Make sure that this setting is achieved on

both ends of the bottom blade. If the front

roller is adjusted correctly you should be

able to slide the setting bar out from this

position with just a light resistance. If the

resistance is too hard then the front roller is

down too low. If there is hardly any

resistance then the front roller is too high

and further small adjustments are needed.

Remember to double check both ends

several times to ensure uniform adjustment.

Finally tighten the roller adjuster locking

nuts. After tightening these, re-check the

height of cut to see that nothing has moved.

If it has, then re-adjust as necessary.

Otros manuales para LM56 Series

Este manual sirve para los siguientes modelos

Otros manuales de Cortacésped de Baroness

Baroness

Baroness LM531 Manual de operación

Baroness

Baroness LM2700 Manual

Baroness

Baroness LM315GC Manual de operación

Baroness

Baroness SUPER MOWER LM180B Manual de usuario

Baroness

Baroness LM285 Manual de operación

Baroness

Baroness LM66GC Manual de operación

Baroness

Baroness LM2700 Manual de operación

Baroness

Baroness SP05 Manual de usuario

Baroness

Baroness LM2700 Manual

Baroness

Baroness LM551 Manual de usuario

Baroness

Baroness GM1700 Manual de operación

Baroness

Baroness LM315GC Manual de operación

Baroness

Baroness LM315GC Guía de configuración

Baroness

Baroness GM2810A Manual de operación

Baroness

Baroness LM2400 Manual de operación

Baroness

Baroness LM315GC Manual

Baroness

Baroness GM2800A Manual de usuario

Baroness

Baroness LM2400 Manual de operación

Baroness

Baroness LM180 Manual

Baroness

Baroness LM18G Series Manual de usuario

Baroness

Baroness LM18GC Manual de operación

Baroness

Baroness LM54GB Manual de usuario

Baroness

Baroness LM2400 Manual de operación

Baroness

Baroness LM54GA-R Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario