Barnett Engineering PRO TALK CV2 Manual de usuario

INSTRUCTION MANUAL

1272M001

Manual Revision: 9.4 - November 2007

Contents

1 GettingStarted .................................... 1-1

2 Operations Overview

Cv2 capabilities (Advanced Mode) ........................... 2-1

Whatconstitutesanalarm? .............................. 2-1

How are alarms processed? .............................. 2-2

What actions should occur when an alarm is detected? ...... 2-3

How do you want to respond to an alarm call? .............. 2-4

Whatifanalarmisnotacknowledged? .................... 2-4

WhatdoyouwanttheCv2todowhenyoucallit? ........... 2-4

Sendingremotecontrolcommands ....................... 2-5

Cv2 capabilities (Basic Mode) ............................... 2-5

Whatconstitutesanalarm? .............................. 2-6

How are alarms processed? .............................. 2-6

What actions should occur when an alarm is detected? ...... 2-6

How do you want to respond to an alarm call? .............. 2-7

Whatifanalarmisnotacknowledged? .................... 2-7

WhatdoyouwanttheCv2todowhenyoucallit? ........... 2-7

Sendingremotecontrolcommands ....................... 2-7

Indicators .................................... 2-8

Troubleshooting .................................... 2-8

3 Installation

Antennarequirements .................................... 3-1

Mounting .................................... 3-1

Input port connections .................................... 3-2

Outputportconnections ................................... 3-4

Configurationprogrammingconnection ...................... 3-4

4 Configuration with the PC

PCrequirements .................................... 4-1

Installingtheprogram .................................... 4-1

Startingtheconfigurationprogram .......................... 4-1

How to access programming functions ....................... 4-1

Program Functions - Advanced mode ........................ 4-2

Program Functions - Basic mode ............................ 4-3

ConfiguringtheCv2-Advancedmode ....................... 4-4

Hardware .................................... 4-4

Points .................................... 4-6

Groups .................................... 4-11

Directories .................................... 4-14

General .................................... 4-16

Configurationprogramming.............................. 4-19

ConfiguringtheCv2-Basicmode ........................... 4-20

Alarms .................................... 4-20

Controls .................................... 4-21

General .................................... 4-22

Directories .................................... 4-22

5 Remote Data Access .................................... 5-1

6 Voice Storage and Configuration with the Telset

Setup .................................... 6-1

Access .................................... 6-1

Commands .................................... 6-2

Telsetprogrammingsummary .............................. 6-3

Programmingflowchart.................................... 6-4

7 VoiceEditor .................................... 7-1

8 Specifications .................................... 8-1

9 Transceiver Codes .................................... 9-1

10 Warranty .................................... 10-1

B1272M001 BARNETT ENGINEERING LTD. ProTalk Cv2

Regulatory Notices

CAUTION

The ProTalk Cv2, model B1272D, has been certified by the Federal Communications

Commission (“FCC”) using the included articulating dual-band dipole antenna. Unauthorized

modifications or changes not expressly approved by Barnett Engineering Ltd. could void

compliance with regulatory rules, and thereby your authority to use this equipment.

ANTENNA CONSIDERATIONS

The included articulating dual-band dipole antenna installation must provide a separation

distance of 20 cm (8") or more between the antenna and all persons to satisfy Maximum

Permissible Exposure (MPE) compliance.

INTERFERENCE TO MEDICAL DEVICES

The ProTalk Cv2, model B1272D, contains an embedded cellular telephone module. Do not use

this device in health care facilities where cellular phone use is restricted.

Interference to pacemakers, hearing aids, and other medical or personal electronic devices may

occur. Consult the manufacturer of those devices to determine if they are adequately shielded

from external RF energy. Your physician may be able to assist you in obtaining this information.

POTENTIALLY UNSAFE AREAS

Do not use this device in any area or facility where posted notices restrict the use of cellular

phones.

FCC COMPLIANCE

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which the user will be required to correct the interference at his own expense.

INDUSTRY CANADA COMPLIANCE

This Class A digital device complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à norme NMB-003 du Canada.

IDENTIFICATION:

FCC ID: OVFKWC-M200

Industry Canada ID: IC:3572A-M200

Getting Started 1-1

B1272M001 BARNETT ENGINEERING LTD. ProTalk Cv2

1. Getting Started

The Cv2 is a very flexible device capable of monitoring discrete or analog inputs and reporting

alarm conditions at these inputs. It is also capable of controlling multiple outputs. Before the

Cv2 is placed into service it must be programmed for the type of operation you require.

The Cv2 contains an embedded CDMA transceiver. To activate the internal CDMA module,

you must do the following:

#If you do not already have a network service account you will need to contact a desired

network service representative and setup an account.

#For activation you will need to provide the ESN of the unit, the ‘home’ location where it

will be installed as well as a billing address and contact name.

#Your network service representative will provide a 10 digit telephone number that you will

program into the unit.

This can be done using the PC configuration software or a telephone set connected to the Cv2.

To use the programming application install the software according to the instructions in section

4-1, connect the powered Cv2 to the computer with the cable provided then activate the

transceiver programming function by selecting Program/Cellphone from the menu. Enter the 10

digit telephone number where shown and press the Store button to transfer the number into the

unit.

To program the mobile number with a telephone set, plug the set into the programming port of

the powered Cv2 and take the set off-hook. The Cv2 will respond with “Enter Program Code”

when you take the set off-hook. Follow this sequence:

You: enter the digit 9

Cv2: “ESN is 067 point 12345678" . . . . . . . . . . . . . . . . (unit speaks ESN)

You: enter the digits ** . . . . . . . . . . . . . . . . . . . . . . . . . . (advance to MIN)

Cv2: “Mobile Number is 800 555 1212 . . . . . . . . . . . . . (unit speaks MIN)

You: enter the digits 800 268 2646 ** . . . . . . . . . . . . . . (change the MIN)

Cv2: “Mobile Number is 800 268 2646" . . . . . . . . . . . . (unit speaks new MIN)

You: enter the digits ** . . . . . . . . . . . . . . . . . . . . . . . . . . (accept the new MIN)

or re-enter the MIN and repeat the process

Cv2 “Enter Program Code” (unit returns to the main program menu)

You: hangup - the number programming is completed

Read this manual carefully before proceeding with the installation and programming of the Cv2.

There are two modes of operation available: Advanced and Basic. In Basic mode multiple

Advanced functions are combined into a single Basic function for ease of programming. When

the unit is configured for Basic operation, all of the variables that can be set by the PC during a

programming session can also be modified remotely by calling the unit with a TouchTone

telephone. Advanced mode operation allows full use of all functions in the Cv2 but limits the

items that can be remotely modified.

Basic mode eliminates the need to configure the Hardware Inputs, Groups and Points by

combining them into a single function called Alarms. Similarly, the outputs are reduced to a

Getting Started 1-2

B1272M001 BARNETT ENGINEERING LTD. ProTalk Cv2

single function called Controls. The number of directories is reduced from 6 to 2 in Basic mode.

It is possible to retain the Advanced directory commands even if the overall programming is set

for Basic operation.

It is important to establish whether Basic or Advanced programming is suitable for your

application. The mode is set by the configuration uploaded from the PC and cannot be altered

using the programming phone. It is possible to switch programming modes during the PC

programming session. When changing from Basic to Advanced there is no loss of data so it is

possible to quickly setup a unit in Basic mode then switch to Advanced to add some extra

functions. Keep in mind that remote programming capabilities are very limited in Advanced

mode. Changing from Advanced to Basic mode will destroy all of the programming information

except the directories which have the option of remaining in Advanced mode.

All of the telephone numbers that are entered into a directory should be carefully checked to

ensure that they are valid numbers. After the Cv2 has been programmed, a test should be

performed to confirm that these numbers are called correctly. The Cv2 has built-in network

protection that will alter the operation of the Cv2 if invalid numbers are called.

To prevent excessive failed calls on the cellular network, the Cv2 has a built-in method for

counting unacknowledged calls. This process works by counting the number of unacknowledged

calls that have been made and then taking action to alert the user that a large number of failures

are taking place. If the problem is not corrected and the Cv2 continues to place failed calls it will

eventually stop calling.

Rules for this process are:

The number of unacknowledged calls is counted for each directory; receipt of an

acknowledgment resets the counter. A retry on the same number is not counted.

If the counter exceeds 50 a “directory alarm” is created. This alarm is not latched and will be

cleared when an acknowledgment is received.

This “directory alarm” appears as a new alarm in all groups causing each group to call out and

notify the user that the alarm is present. This alarm is announced before the Site ID by speaking

“Directory X Error” where X is the directory that has failed to be acknowledged for at least 50

call out cycles.

If an interrogate code is received, the “Directory X Error” message will be made before any

group alarms.

If the total number of unacknowledged calls in all directories exceeds 75, a call will be made to

Barnett Engineering with the MIN and ESN of the phone. This information will be used to

attempt to locate the owner of the equipment and notify them of the problem condition. At this

point the timer used to control the interval between the last call in the directory and when the

cycle is restarted at the first number will be set to 4 hours regardless of the program settings.

If the total number of unacknowledged calls exceeds 100, the Cv2 will cease to call out. The

Cv2 will still answer incoming calls and reset the counters if an acknowledge code is received.

Each chapter has separate sections for Basic and Advanced operations. Once the mode that you

want to operate in has been established, use the applicable section in each chapter.

A comparison or the functions available for each mode is shown in Table 1.

Getting Started 1-3

B1272M001 BARNETT ENGINEERING LTD. ProTalk Cv2

Table 1 Mode Comparison

Function Advanced Mode Basic Mode

Input debounce Independent for each input Part of Alarms - same setting for all

Input NO/NC Independent for each input Part of Alarms - same setting for all

Input type 8 inputs - 1 analog, 4 digital types 8 Alarms - 1 digital type only

Output type 8 outputs - On/Off or timed 8 Controls - 3 On/Off or timed

4 can be special function 5 always special function

Groups 6 groups each with separate Not used

Acknowledge code Part of Directories

Interrogate code Part of Directories

Short and long timer Part of Directories - Cycle timer

Shift control ---

Group enable ---

Ack request enable ---

Auto Ack enable ---

Points 30 points, can be any input/output Not used

Using group ---

Enable Part of Alarms - same setting for all

Latched Part of Alarms - same setting for all

DTMF tag ---

Alarms Not used 8 alarms

--- Using Directory A/B or disabled

--- NO/NC - same for all Alarms

--- Momentary or Latched - same for all

Directories 6 directories 2 directories

Dial Directories commands can be Basic

Voice or Advanced when programming in

DTMF the Basic mode. Only phone

Wait numbers can be programmed in

Alert Basic mode.

Signal Acknowledge code

Answer Interrogate code

--- Cycle Timer

General Rings before answer Rings before answer

Call progress enable Call progress enable

Access code Access code

Temporary Ack time Temporary Ack time

Enable Modem code Enable Modem code

Security levels —

Shift change code —

Operations Overview 2-1

B1272M001 BARNETT ENGINEERING LTD. ProTalk Cv2

2. Operations Overview

The purpose of this chapter is to provide an overview of the Cv2 capabilities. Chapter topics are

organized in the same order that you would follow in setting up the system.

For more details on configuring the operation through the programming software, refer to

Chapter 3, Configuration.

2.1 Cv2 Capabilities (Advanced mode)

When an alarm occurs, the Cv2 places a call using its built-in cellular phone and announces

the alarm condition using stored voice messages. Alarm messages consist of the site ID

phrase, the group phrase and the alarm message phrase that are stored at voice programming

time. The group phrase is used if the alarms have been grouped to provide different activities

for different alarm conditions. The unit can also be called up and interrogated to obtain

current alarm conditions and readings.

The Cv2 has eight hardware inputs that can be programmed to accept either digital or analog

signals and eight hardware outputs. Inputs can be independently configured to operate in

these modes:

digital monitoring contact closures or voltage levels

watchdog monitoring for the absence of a periodic event

totalizer counting events

interval measuring the time duration of events

analog measuring 0 to 5 volt signals

Outputs can be set to operate as either on/off controls or as timed controls.

2.1.2 What constitutes an alarm?

Alarm conditions can be defined for digital, watchdog and analog inputs. Totalizers and

interval inputs are used for measurement purposes and do not generate alarms. The signal at

the input is conditioned by a debounce timer that ensures the level is valid before accepting it.

A digital input has normal and alarm states that can be defined as either when the input is high

or low. After the input signal has been qualified by the debounce timer, it can be registered as

an alarm when the input is active, or it can be latched to detect a pulsed condition. The voice

message for a digital input is programmed to announce the alarm condition that it is

monitoring, e.g. “Intrusion Alarm”.

Watchdog inputs use a timer that is restarted by changes at the input. If this timer expires

because it has not been restarted within the programmed interval, an alarm will register. Like

the digital input, the watchdog can be set as either an active-only or latched alarm. The voice

message for a watchdog is similar to a digital, e.g. “Tower Strobe Failure”.

Analog inputs convert the voltage level to a digital value and perform a comparison against

the programmed low and high setpoints. An alarm is present when the measured value is

above or below the setpoint. Alarm messages are spoken using the stored phrase with either

Operations Overview 2-2

B1272M001 BARNETT ENGINEERING LTD. ProTalk Cv2

HARDWARE

INPUTS

INPUTS 8

OUTPUTS

POINTS

UP TO 30 INPUTS OR OUTPUTS

GROUP

CELL PHONE

HARDWARE

OUTPUTS

GROUP

DIRECTORY

ADIRECTORY

DIALOUT

COMMANDS CONTROL

COMMANDS

Figure 1

Cv2 Block Diagram - Advanced Mode

“High” or Low” appended depending on which setpoint has been exceeded. The actual

reading, including decimal place notation and engineering units, is spoken when the Cv2 is

interrogated.

The latching alarm function is also available for analog inputs.

2.1.3 How are alarms processed?

The way in which the Cv2 processes alarms is shown in Figure 1.

The hardware input and output ports are activated in the Points section to become part of the

monitoring and control process. There are 30 points which can be referenced to any of the I/O

ports. This allows an analog input to be used by more than one point and monitored for

multiple setpoints, as would be the case where minor and major alarms are required.

If you do not want all of the points to generate the same response when they detect alarms,

they can be placed into different groups. Six groups are available, each with independent

timers and control codes. When a group detects an alarm condition in one of its assigned

points, it executes the sequence of actions found in the current directory. A group can use any

of the six directories to perform the call out function, plus the directory selection can be

changed by using the shift control feature.

Operations Overview 2-3

B1272M001 BARNETT ENGINEERING LTD. ProTalk Cv2

2.1.4 What actions should occur when an alarm is detected?

All alarm conditions will be processed by placing a call on the cellular phone. The called

number and the activities that occur with different alarms are determined by entries in the

directories. A directory contains the sequence of actions that will occur when a group has an

active alarm. Instructions for dialing, speaking, inserting delays and signaling are placed in the

directory in the order in which they are to be performed. There are a total of six directories; each

can contain a unique sequence of activities that will be performed when alarm conditions exist.

To best describe how a directory controls alarm reporting activities, an example directory

programming session follows. For more information on the directory summary and dialog

box, refer to Chapter 3. The opening window for a directory displays a summary of the

activities that it will perform when an alarm is detected. The directory summary is arranged

as lines; each line represents the sequence of events that will take place during one call out. If

a Dial command is the first entry on the line, the Cv2 will call the programmed number and

then execute the remainder of the commands on that line. After the last command on the line

is competed, the call will be terminated. Commands such as Auto Ack and Wait, when used

as single line commands, do not initiate a call. For a basic sequence where the Cv2 is to call a

phone number and speak the alarm message, the directory line contains the Dial and Voice

commands appearing as:

1. [DIAL]2458829 [VOICE]

This line will cause the Cv2 to place a call to 245-8829 and then speak the Site ID, Group

Name and alarm message, or messages, for all active points. Unless programmed not to, the

Cv2 will append the phrase “Enter Acknowledge Code” at the end of the alarm announcement

and wait for the code to be returned. If the code is received, the alarm sequence will be

terminated until a new alarm occurs. Failure to receive an Acknowledge Code will advance

the sequence of operations to the next line in the directory. If the commands contained in the

last directory line have been completed without reception of an Acknowledge Code, the Cv2

waits for the time interval set in the timers before repeating the process by starting over at

directory line 1.

During execution of the Voice command, the Cv2 will try to announce the alarm messages

three times with a one minute limit for the total announcement duration.

For example, to call four telephone numbers, the directory would appear as:

1. [DIAL]2458829 [VOICE]

2. [DIAL]2336700 [VOICE]

3. [DIAL]9842121 [VOICE]

4. [DIAL]9843316 [VOICE]

If you want an alert tone to precede the voice message the directory line would look like this:

1. [DIAL]2458829 [ALERT] [VOICE]

The next example shows a sequence that is used to call a numeric paging terminal. After the

call is placed there is a four second delay for the paging terminal to respond before the Cv2

sends the number to be displayed on the pager. When calling a paging terminal, it is

sometimes useful to allow the called party time to call the Cv2 back and acknowledge the

Otros manuales para PRO TALK CV2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Alarma de coche de otras marcas

Clifford

Clifford 3606X Manual de usuario

Ultra Start

Ultra Start 2500M SERIES Manual de usuario

Ultra Start

Ultra Start 650 Series Manual de usuario

Audiovox

Audiovox Prestige Platinum+ APS-511C Manual de usuario

Sparkrite

Sparkrite SRA8 Manual de usuario

Viper

Viper 4708V Manual de usuario

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manual

Falcon

Falcon Predator XL3 Guía del usuario

Audiovox

Audiovox Auto Security XR91 Instrucciones de funcionamiento

Clifford

Clifford Sabre II Manual de usuario

CrimeStopper

CrimeStopper CS-8717 Guía de inicio rápido

Ultra Start

Ultra Start 450 SERIES Manual de usuario

Scytek electronic

Scytek electronic Vectra X3 Manual de usuario

Excalibur

Excalibur AL-1860-EDPB Manual de usuario

Clifford

Clifford CYBER 2 Manual de usuario

Gemini

Gemini 7057 Manual de usuario

FlashLogic

FlashLogic FLRSBA PRESTIGE Manual de usuario

Magicar

Magicar FAI-440 Manual de usuario