Bargeheights LED PAR Manual de usuario
User Manual
RGB Wash Luminaire
LED PAR
LED PAR User Manual rev. A
TABLEOFCONTENTS
1. The Beginning
Unpacking
Support
Introduction
DMX Quick Reference
2. Safety Information
3. Setup
DMX Cabling
DMX Termination
3-pin vs. 5-pin
Master/Slave Mode
4. Operation/Conguration
Menu Structure
DMX Control Mode
1 Channel Mode
2 Channel Mode
3, 4, 5 Channel Modes
6, 7 Channel Modes
Standalone Control Modes
Master/Slave Mode
RGB Balance Mode
LED Display
TechnicalSpecications
Photometric Data
5. Care/Maintenance
Returns
Shipping Damage
Contact Us
3
3
3
4
4
5
6
6
6
7
7
8
9
10
11
12
13
14
15
16
16
17
18
18
19
19
20
20
Page 3©2010 Bargeheights, Inc.
1. THEBEGINNING
Thanks!
Thank you for choosing the Bargeheights LED PAR! This versa-
tile PAR-style LED wash luminaire will provide reliable perfor-
mance day in and day out. To ensure long lasting performance,
please follow the guidelines in this manual. The instructions
here are important for your safety and the maintenance of this
xture.Enjoy!
Unpacking
All of our luminaires are thoroughly tested prior to being
shipped. While your LED PAR functioned perfectly when it left
us, it may have been bumped around during shipping. Please
inspect the carton and if you notice any damage, take a good
lookatthexture.Ifyouseeanydamage,itisimportantto
contactoursupportteamrightaway.And,ifyoundanypieces
necessary for operation are missing – let us know! We’ll make it
right as soon as possible.
Support
If something is not working properly, let us know! Grab a com-
puter or your favorite handheld device and head to
www.bargeheights.com/support for user manuals, DMX
channel lists and support information. You can also email us at
WARNING!
Toreducetheriskofreorelectricalshock,donotattemptto
usethisxturewithanycoversmissingorremoved.
The Bargeheights LED PAR carries a one-year (365 day) manu-
facturers’ limited warranty. Please contact Bargeheights for
warranty repair or returns. All returns require an SR (Service
Request)number.Ifyourxtureisstillunderwarranty,contact
us and we’ll walk you through the process.
Page 4 LED 36 User Manual rev. A
Introduction
•PAR-styleLEDWashLuminaire
•FullRGBcolormixingvia183LEDs
(60 Red, 63 Green, 60 Blue)
•Highoutput,lowpowerconsumption
•Variableelectronicstrobe
•Variableelectronicdimmer
•Master/Slavemodes
•Built-instandalonemodes-nocontrollerrequired!
•RGBcolormixingabilityinstandalonemode
•Upto7DMXcontrolchannels
•Ruggedaluminumchassis
•Passivecooling-nofan
DMX Quick Reference - 4 Channel Mode
Channel Function
1 Red Intensity
2 Green Intensity
3 Blue Intensity
4 Overall Intensity
Page 5©2010 Bargeheights, Inc.
2. SAFETYINFORMATION
•DONOTconnectthextureintoadimmer.Useconstantlinevoltageonlyto
avoid damage.
•Makesureyouareconnectingthexturetolinevoltagethatisnothigher
thanthevoltagestatedontherearofthexture.
•TheLEDPARisforindooruseonly.Donotexposethexturetorain,or
other moisture. The LED PAR cannot be used as a buoy.
•Donotoperatethexturewithammableitemsnearby.NEVERlayanything
onthexturewhileitison.
•Giveitspace!TheLEDPARneedsatleast6in(15cm)fromothersurfaces
andobjects.Makesurethatnoneoftheventilationorfanslotsareblocked.
•ALWAYSdisconnectthexturefromitspowersourcebeforeservicingor
cleaning.
•ALWAYSsecureyourLEDPARusingasafetycable.NEVERhangorcarryit
by its cord. It has a yoke for a reason!
•DONOToperatewhentheambienttemperaturesarehigherthan104°F
(40°C).Ifit’stoohotforyou,it’stoohotforyourLEDPAR!
•IfyourLEDPARstopsworkingproperly,stopusingitimmediately.NEVER
trytorepairityourself.Attemptingrepairsintheeldcanresultindamageor
injury.Pleasecontactusforrepairsorreplacement.
•Makesurethepowercordisnotfrayedordamaged.
•Neverdisconnectthepowercordbypullingonthecord.Usetheplug!
•Avoiddirecteyeexposuretothelightsourcewhileitison.It’scoollooking,
and fun to watch, but staring into the light can damage your eyes!
Therearenouserserviceablepartsinsidethisxture.Donot
openthehousingorattemptanyrepairsyourself.Notonlyisit
a bad idea, it will void your warranty – which is a bummer when
you need a working light! If you do need service, please contact
Bargeheights.Damagessustainedasaresultofmodications
tothexture,ordisregardinginformationinthismanualwill
not be covered by your warranty. If something is wrong, let us
take a look at it. We’ll help you out!
!Caution!
Page 6 LED 36 User Manual rev. A
3. SETUP
DMX Cabling
The LED PAR has standard 3-pin XLR connectors for DMX con-
trol and daisy-chaining. Up to 32 devices can be daisy-chained
together on a single run. Standard microphone cables will
probably work OK, but DMX is a serial data transmission with
impedancespecicationsthataredifferentthananalogaudio.
CablesspecicallydesignedtotransmitDMXsignalswillalways
workbest.Asanexample,Belden©9841meetsthespecica-
tions for DMX-512 applications. The longer the cable distance,
the more important proper cable selection is.
DMX Termination
Sometimes, errors will crop up in your DMX line – especially if it
isalongrun.Whenthisisthecase,orifyoujustwanttomake
sure your DMX runs have the best chance at accurate transmis-
sion, you can use a terminator. A terminator is a 120 ohm ¼
watt resistor which is connected between pins 2 and 3 of a male
XLR connector (DATA + and DATA -). This connector is inserted
inthefemaleXLRconnectorofthelastxtureinyourdaisy
chain to terminate the line. Using a cable terminator will de-
crease the possibility of erratic behavior. Terminators are avail-
able on the internet and from lighting retailers. If you’re handy
with a soldering iron, they are simple to build yourself!
1
120 Ohm resistor
¼ watt
DMX Terminator
3-pin XLR Male connector
1
2
3
1
2
3
Shield
Data +
Data -
2
3
Page 7©2010 Bargeheights, Inc.
3-pin vs. 5-pin
Some manufacturers use 5-pin XLR connectors for DMX trans-
mission. Don’t worry! The two are still compatible. Adapters are
available on the internet and from lighting retailers. If you want
to build your own, here are the proper connections:
Cable Conductor 3-pin Female
(output)
5-pin Male
(input)
Shield (Ground) Pin 1 Pin 1
DMX Data + Pin 2 Pin 2
DMX Data - Pin 3 Pin 3
not connected - not connected
not connected - not connected
Master/Slave Mode
The LED PAR also has a Master/Slave mode. In this mode you
cansetonextureinthelinetoactasthemastercontroller–
andupto32otherxturescanbeconnectedandwillmirrorthe
operationoftherst.Inthisconguration,youdonotneeda
DMX controller.
Connectthexturesjustas
you would for DMX control.
See the OPERATION sec-
tion of this manual for more
information on how to set up
Master/Slave mode.
DMXIN DMX OUT
DMXIN DMX OUT
Master Fixture
Slave Fixture
to next xture
Page 8 LED 36 User Manual rev. A
4. OPERATION/CONFIGURATION
We here at Bargeheights don’t really care for DIP switches.
They are hard to see in the dark, and since most of us don’t
quickly think in binary, they are tricky to set properly. The
LED PAR has an LED display with a simple menu system. There
are four control buttons below the display that allow you to
navigate the control menus.
<MENU>–Goupalevelinthemenusystem;holdtoconrm
<DOWN>–Scrolltothenextlowernumberormenuselection
<UP>–Scrolltothenexthighernumberormenuselection
<ENTER> – Select the current number / menu selection
To access the main menu press the <MENU> button. Use the
<UP> or <DOWN> buttons to navigate through the menu
options. Press the <ENTER> button to select the option dis-
played, and use the <UP> or <DOWN> buttons to change the
settings. Once your changes are made press <ENTER> to ac-
cept the change. Hold <MENU> for three seconds to con-
rm the settings change.
If the LED PAR menu remains static for more than eight sec-
ondsitwillautomaticallyreturntoitslastsetting.Toexitthe
menu without making any changes press the <MENU> button.
8888
MENU DOWN UP ENTER
Page 9©2010 Bargeheights, Inc.
Menu Structure
Addr
ShNd
Led
Idsp
ChNd
sLNd
baLa
1-512
Soun
on
off
Fade
Nast
red 0-255
0-255
0-255
coLo
off
on
auto
Noff
Gree
1Ch-7Ch
SL 2
SL 1
bLue
DMX Address Setting
Sound Control Mode
Color Selection Mode
ColorFadeMode
Auto Operation Mode
DMX Channel Mode (1Ch - 7Ch)
Master Mode
ControlOFF
Slave Mode 2
Slave Mode 1
Rear LED Display On
Rear LED Display Off
RearLEDDisplayNormal
RearLEDDisplayFlip
RGB Balance Mode -
Red Level
RGB Balance Mode -
Green Level
RGB Balance Mode -
Blue Level
Page 10 LED 36 User Manual rev. A
DMX Control Mode
To change the DMX starting address:
•Press<MENU> until Addr is displayed.
•Press<ENTER> to display the channel number, and press
<UP> or <DOWN> to select your starting address. (1-512)
•Press<ENTER> to assign your selection, then press and hold
<MENU>forthree(3)secondstoconrmthechange.
NOTE:IfavalidDMXsignalisnotpresent,thexturewillau-
tomatically go into the selected standalone mode. See Stand-
alone Control Modes for more information.
To change the DMX mode (1, 2, 3, 4, 5, 6, or 7 channels):
•Press<MENU> until ChNd is displayed.
•Press<ENTER> to display the mode, and press <UP> or
<DOWN> to select the DMX mode. (1CH - 7CH)
•Press<ENTER> to assign your selection, then press and hold
<MENU>forthree(3)secondstoconrmthechange.
Otros manuales para LED PAR
1
Tabla de contenidos
Otros manuales de Equipo de iluminación de Bargeheights
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
