Bardiani BBWP1 Hoja de especificaciones

Instruction, Use and Maintenance Manual

PNEUMATIC VALVE

WITH DIAPHRAGM

Bardiani Valvole S.p.A.

via G. di Vittorio, 50/52 - 43045 Fornovo di Taro (PR) - Italy

tel. +39 0525 - Fax 0525 3408

[email protected] - www.bardiani.com

EN-IST-BBWP1-0121

BBWP1 - BBWT1

(Translation of the Original Instructions in the italian Language)

EN-IST-BBWP1-0121

INDEX

INTRODUCTION 4

1 Safety,Warning and Mandatory Signs 5

1.1 Operator training 8

2 General safety warnings 9

2.1 General safety warnings 9

2.2 Safety Devices: 9

3 Technical data 10

4 Checking / Unpacking / Lifting 11

5 Installation 12

6 Operation 14

7 Troubleshooting 15

8 Cleaning 16

9 Disposal 17

10 Maintenance 18

10.1 General maintenance 18

10.2 Scheduled maintenance 19

10.3 Tools useful for Disassembly/Reassembly 20

10.4 Pneumatic valve BBWP1 21

10.5 Disassembly of the BBWP1 23

A Disassembly Of BBWP1 L 24

B Dsassembly Of The BBWP1 P7-LL 28

10.6 Assembly of the BBWP1 32

A Assembly Of The BBWP1-L 35

B Assembly Of The BBWP1 P7-LL 39

10.8 Pneumatic valve BBWP1 45

10.9 Disassembly of the BBWP1 Diverter 47

10.10 Assembly of the BBWP1 Diverter 51

10.10 Pneumatic Valves BBWT1 59

10.11 Disassembly of the BBWT1 61

10.12 Assembly of the BBWT1 65

11 Annexes 72

12 2D diagram BBWP1 73

13 2D diagram BBWP1 P7-LL 74

EN-IST-BBWP1-0121

MANUAL REVISION DATE

14 2D diagram BBWP1 Diverter 75

15 2D diagram BBWT1 76

16 Warranty 77

17 Recommendations 78

INTRODUCTION

EN-IST-BBWP1-0121

INTRODUCTION

This “Instruction, Use and Maintenance Manual” has been prepared to provide guidance and

recommendations to assist qualified skilled technicians in the understanding, running and

maintenance orf the Products supplied.

It forms an integral part of the Products supplied and must be read prior to any installation, operation

and/or maintenance of all types of valves provided.

This manual must be saved for future reference and be kept readily available at the unit.

With regards to the use of valves compliant with EU Directive 2014/34/UE (ATEX), consultation of a



The essential characteristics of all types of valves described herein being consistent, the

Manufacturer reserves the right to alter and or complement and or update at any time and with

no obligation to notify so in writing, the data and or information relevant to the use of the valves

described in this "Instruction, Use and Maintenance Manual".

A constantly updated version of this "Instruction, Use and Maintenance Manual" is available at

the Manufacturer's website www.bardianivalvole.it.

Under no circumstance shall the Manufacturer be held liable for consequences resulting from

failure and or improper use of the instructions contained in this Manual and relating to the

installation, operating, maintenance and storage of the products.

Full or part reproduction, transfer and or recording of any part of this "Instruction, Use and

Maintenance Manual" by all means, whether it be electronic, on hard copy, mechanical or any

other means or recording or reuse is strictly prohibited without the prior written consent of the

Manufacturer and for any use other than that of the Buyer.

1 Safety,Warning and Mandatory Signs

EN-IST-BBWP1-0121

1 Safety,Warning and Mandatory Signs

WARNING SIGNS

Pictogram Description Notes

WARNING

General

This tells the person in question that the operation

described involves (when not performed in accordance

with the relative safety regulations) the risk of personal

injury.

WARNING

Hand crushing

Exercise caution in executing the procedure

Hand crushing hazard

WARNING

Heavy loads

Exercise caution in executing the procedure

Heavy suspended loads.

WARNING

Severe burns

Heat emission hazard Very hot surface, risk of severe

burns

WARNING

Risk of explosions

Take Care, risk of explosions

MANDATORY SIGNS (FOR THE OPERATOR IN CHARGE OF ASSEMBLY/DISASSEMBLY)

Pictogram Description Notes

OBLIGATION

General

Special instructions must be followed to avoid injury to

persons.

PROTECTIVE GLOVES Safety gloves must be available for handling objects

which could cause hand injuries.

HARD HAT A hard hat must be worn during machine lifting

operations to protect against hazards generated by

suspended loads.

FOOTWEAR Use safety footwear to protect against the risks of

falling objects during operations to transport the

machine.

SUITABLE CLOTHING Suitable clothing such as overalls. It is strictly

prohibited to wear clothes with large flapping sleeves

and/or other loose items which could easily get caught

up in machine parts.

1 Safety,Warning and Mandatory Signs

EN-IST-BBWP1-0121

MANDATORY SIGNS (FOR THE OPERATOR IN CHARGE OF MECHANICAL MAINTENANCE)

Pictogram Description Notes

OBLIGATION

General

Special instructions must be followed to avoid injury to

persons.

PROTECTIVE GLOVES Protective gloves must be available for handling

objects which could cause hand injuries or when there

is the possibility of coming into contact with harmful

substances..

HARD HAT Hard hats must be available when lifting heavy parts.

FOOTWEAR Use safety footwear to protect against injuries caused

by falling objects during maintenance operations

(particularly when dismantling parts).

SUITABLE CLOTHING Suitable clothing such as overalls. It is strictly

prohibited to wear clothes with large flapping sleeves

and/or other loose items which could easily get caught

up in machine parts.

SAFETY GLASSES Protective glasses must be available when there is the

possibility of contact which harmful substances which

could cause eye injuries.

OPERATING SIGNS

Pictogram Description Notes

SKILLED

PERSONNEL

Dismantling/Assembling and maintenance operations must be

carried out by expert technicians only.

NOTE Follow the indicated note with care

ENVIRONMENTAL

NOTE

Follow the regulations in force in the country of used

governing waste disposal.

CLAMP Use of a clamp

CLAMP WITH SOFT

JAWS

Use of a clamp with jaws made from soft material

1 Safety,Warning and Mandatory Signs

EN-IST-BBWP1-0121

OPERATING SIGNS

Pictogram Description Notes

PRESS Use of a press

PRESS

(release)

Use of a press Gradual release of the pressure force

ELECTRICAL

CONNECTION

Electrical connection to the control unit (consult the relative

instruction manual).

ELECTRICAL

DISCONNECTION

Electrical disconnection from the control unit (consult the

relative instruction manual).

PNEUMATIC

CONNECTION

Connection of the air to the valve.

PNEUMATIC

DISCONNECTION

Disconnection of the air from the valve

1APPLICATION OF

FOODSAFE

GREASE

Use FOODLUBE HI-TEMP 2 grease or similar

2APPLICATION

OF FOODSAFE

GREASE

Use FOODLUBE Multi-paste grease or similar

APPLICATION OF

MULTIPURPOSE

GREASE

Use AGIP GREASE MU EP 2 SE or similar

THREADLOCK

APPLICATION

Use SPEED BOND M500 threadlock or similar

OPTIONAL

1 Safety,Warning and Mandatory Signs

EN-IST-BBWP1-0121

1.1 Operator training

All persons who have to work on the valve must be qualified to carry out the relative

maintenance tasks. They must be informed as to the possible hazards involved and must

observe all the safety instructions set out in this manual. Allow expert personnel only to

work on the electrical components.

2 General safety warnings

EN-IST-BBWP1-0121

2 General safety warnings

2.1 General safety warnings

Intended use

Bardiani valves have been designed exclusively for moving fluids.

Prohibited use

The valve must not be used:

• for any operations different to those described under the heading “Intended Use”,

• for handling fluids different to the type specified by the manufacturer and indicated in the valve's

technical data;

• for moving fluids at different pressures to those envisaged by the manufacturer and indicated in the

valve's technical data.

Limitations on valve use

It is forbidden to:

• use the valve in a construction configuration different to the one envisaged by the manufacturer.

• use the valve where there is a risk of explosion and/or fire, unless envisaged by the manufacturer (if

the valves are certified in accordance with Directive 2014/34/EU, please refer to the ATEX Manual)-;

• integrate other systems and/or equipment which were not considered by the manufacturer during the

executive design phase,

• use the valve for purposes other than those specifically envisaged by the manufacturer.

WARNING

The machine may not he used inside premises where there is a potentially explosive atmosphere or



with Directive 2014/34/EU please refer to the ATEX Manual).

BARDIANI VALVOLE S.p.A. declines all liability for installation,

use or maintenance which fails to comply with the indications

provided in this manual!

2.2 Safety Devices:

(see the control unit manual)

3 Technical data

EN-IST-BBWP1-0121

3 Technical data

VALVE DATA

Maximum pressure 10 bar

Maximum seal pressure See catalogue

Storage temperature from -10°C to +25°C

Material in contact with the product AISI 316L (1.4404). Check the resistance to corrosion in relation to

products and detergents

Gasket material in contact with the product EPDM, FKM, HNBR, P.T.F.E. and other gaskets on request. Check

compatibility with products and detergents

Surface finish in contact with the product Ra 0.8 µm. Other finishes available on request

PNEUMATIC ACTUATOR DATA

Connectors 1/8” BSP

Pipe dimensions 6 mm external diameter, 4 mm internal diameter

Air pressure from 6 bar (87 psi) to 8 bar (116 psi)

Air quality Class 2, 4, 3 ISO8573-1

External material AISI 304L (1.4307)

Seals NBR

Noise levels 76 dB

Electrical supply See Giotto Top

GASKET MATERIALS COMPATIBILITY

Product EPDM FKM HNBR MVQ

Temperature (applications with air) from -10 to 140°C from -10 to 200°C from -10 to 130°C from -70 to 230°C

Caustic soda 2% 60°C 30°C To be checked Unsuitable

Nitric Acid 2% 60°C 80°C To be checked Unsuitable

Saturated steam 125°C Suitable To be checked Suitable Unsuitable

Greases Unsuitable Suitable Suitable Unsuitable

Alcohols Suitable Unsuitable Suitable Suitable

The valve complies with PED 2014/68/EU directive, with special reference to

Annex III, Module A, concerning internal manufacturing checks as indicated in the

Conformity Assessment Procedures.

Valves with DN equal or smaller than DN25 are not included in compliance with Article 4, paragraph 3.

Valves designed for use with gases, liquefied gases, gases dissolved under pressure, vapours and also those liquids whose

vapour pressure at the maximum allowable temperature is greater than 0,5 bar above normal atmospheric pressure (1

013 mbar) are included within the following limits:

- valves with DN between DN32 and DN100 (included) with group 1 fluids;

- valves with DN125 or bigger with group 2 fluids.

The end user is asked to carry out the acoustic emission tests once the valve has been installed in the destination

plant.

In the event of any doubt, please contact Bardiani Valvole S.p.A.

Este manual sirve para los siguientes modelos

Otros manuales de Unidad de control de Bardiani

Bardiani

Bardiani BBZK Hoja de especificaciones

Bardiani

Bardiani BBZS1 Hoja de especificaciones

Bardiani

Bardiani Giotto-Top Instrucciones de operación

Bardiani

Bardiani BBYQ Hoja de especificaciones

Bardiani

Bardiani YPA Manual de usuario

Bardiani

Bardiani BBZK Manual de usuario

Bardiani

Bardiani BBZO Hoja de especificaciones

Bardiani

Bardiani BZAW3 Hoja de especificaciones

Bardiani

Bardiani BBZS5 Manual

Bardiani

Bardiani B935 Manual de usuario

Bardiani

Bardiani ZQ Manual de usuario

Bardiani

Bardiani BBYO Hoja de especificaciones

Bardiani

Bardiani VVF Hoja de especificaciones

Bardiani

Bardiani BBZS1 Hoja de especificaciones

Bardiani

Bardiani B925 Hoja de especificaciones

Bardiani

Bardiani GIOTTO TOP Hoja de especificaciones

Bardiani

Bardiani BZAW3PG Hoja de especificaciones

Bardiani

Bardiani B935 Hoja de especificaciones

Bardiani

Bardiani BBZS5 Manual

Bardiani

Bardiani J-GIOTTO TOP Hoja de especificaciones

Bardiani

Bardiani BBZP Hoja de especificaciones

Bardiani

Bardiani BYAW3 Hoja de especificaciones

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario