Banner Q4X Series Manual de usuario
Quick Start Guide
Class 1 laser CMOS sensor with dual outputs and IO-Link. Patent pending.
This guide is designed to help you set up and install the Q4X sensor with dual discrete outputs and IO-Link. For complete
information on programming, performance, troubleshooting, dimensions, and accessories, please refer to the Instruction
Manual at www.bannerengineering.com. Search for p/n 190074 to view the Instruction Manual. Use of this document
assumes familiarity with pertinent industry standards and practices.
For illustration purposes, the threaded barrel model Q4X images are used throughout this document.
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to
serious injury or death. This device does not include the self-checking redundant circuitry necessary
to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an
energized or de-energized sensor output condition.
Features
1
2
3
Figure 1. Sensor Features—Threaded Barrel
Models
1. Output Indicator (Amber)
2. Display
3. Buttons
1
2
3
Figure 2. Sensor Features—Flush Mount
Models
Display and Indicators
The display is a 4-digit, 7-segment LED. The main screen is the Run mode screen.
For 2-pt, BGS, FGS, and DYN TEACH modes, the display shows the current distance to the target in millimeters. For dual
TEACH mode, the display shows the percentage matched to the taught reference surface. A display value of
indicates the sensor has not been taught.
12
Figure 3. Display in Run Mode
1. Stability Indicator (STB—Green)
2. Active TEACH Indicators
• DYN—Dynamic (Amber)
• FGS—Foreground Suppression (Amber)
• BGS—Background Suppression (Amber)
Note: The indicators represent the currently selected channel. However, if Output 2 is set to something
other than LO, DO, or Complementary, then the indicators represent the Channel 1 status.
Q4X Stainless Steel Laser Sensor with Dual
Discrete Outputs and IO-Link
Original Document
190073 Rev. E 17 January 2017
190073
Output Indicator
•On—Output is on
• Off—Output is off
Active TEACH Indicators (DYN, FGS, and BGS)
• DYN, FGS, and BGS all off—Two-point TEACH mode
selected (default)
• DYN on—Dynamic TEACH mode selected
• FGS on—Foreground suppression TEACH mode
selected
• BGS on—Background suppression TEACH mode
selected
• DYN, FGS, and BGS all on—Dual TEACH mode
selected
Stability Indicator (STB)
•On—Stable signal within the specified sensing range
• Flashing—Marginal signal, the target is outside the
limits of the specified sensing range, or a multiple
peak condition exists
• Off—No target detected within the specified sensing
range
Buttons
Use the sensor buttons (SELECT)(TEACH), (+)(CH1/CH2), and (-)(MODE) to program the sensor.
(SELECT)(TEACH)
•Press to select menu items in Setup mode
• Press and hold for longer than 2 seconds to start
the currently selected TEACH mode (the default is
two-point TEACH)
(+)(CH1/CH2)
•Press to navigate the sensor menu in Setup mode
• Press to change setting values; press and hold to
increase numeric values
• Press and hold for longer than 2 seconds to switch
between Channel 1 and Channel 2
(-)(MODE)
•Press to navigate the sensor menu in Setup mode
• Press to change setting values; press and hold to
decrease numeric values
• Press and hold for longer than 2 seconds to enter
Setup mode
Note: When navigating the menu, the
menu items loop.
Laser Description and Safety Information
CAUTION: Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure. Do not attempt to disassemble this sensor for
repair. A defective unit must be returned to the manufacturer.
Class 1 Lasers
Class 1 lasers are lasers that are safe under reasonably foreseeable conditions of operation, including the use of optical
instruments for intrabeam viewing.
Laser wavelength: 655 nm Output: < 0.20 mW Pulse Duration: 7 µs to 2 ms
Q4X Stainless Steel Laser Sensor with Dual Discrete Outputs and IO-Link
2 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 190073 Rev. E
Otros manuales para Q4X Series
13
Este manual sirve para los siguientes modelos
1
Otros manuales de Accesorios de Banner
Banner
Banner DF-G1 Expert Manual de usuario
Banner
Banner Q4X Series Manual de usuario
Banner
Banner L-GAGE LE250 IO-Link Manual de usuario
Banner
Banner L-GAGE LH Series Manual de usuario
Banner
Banner D10 Expert Series Manual de usuario
Banner
Banner iVu PLUS TG Manual de usuario
Banner
Banner Q5X Manual de usuario
Banner
Banner iVu PLUS TG Manual de usuario
Banner
Banner Q4X Series Manual de usuario
Banner
Banner Q4X Series Manual de usuario
Banner
Banner Q4X Series Manual de usuario
Banner
Banner L-GAGE LTF Manual de usuario
Banner
Banner iVu Plus BCR Gen2 Series Manual de usuario
Banner
Banner Registration Mark Sensor R58 Expert Manual de usuario
Banner
Banner L-GAGE LE250 IO-Link Manual de usuario
Banner
Banner iVu Plus BCR Gen2 Series Manual de usuario
Banner
Banner Q5X Manual de usuario
Banner
Banner QM26 Series Manual de usuario
Banner
Banner World-Beam QS18 Series Manual de usuario
Banner
Banner Q3X Manual de usuario
